PREPARATION OF SILVER POWDER FOR CONDUCTIVE PASTE

ＰＲＥＰＡＲＡＴＩＯＮＯＦＳＩＬＶＥＲＰＯＷＤＥＲＦＯＲＣＯＮＤＵＣＴＩＶＥＰＡＳＴＥＣｈａｉ，Ｌｉｙｕａｎ；Ｚｈｏｎｇ，Ｈａｉｙｕｎ；Ｗｕ，Ｈｕｉｙｕｎ（ＤｅｐａｒｔｍｅｎｔｏｆＮｏｎｆｅｒｒｏｕｓＭｅｔａｌｌｕｒｇｙ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎ...     

NdFeB铸块HD工艺中温度和压力对吸氢行为的影响

对NdFeB铸块在HD工艺中温度和压力对吸氢行为的影响进行了研究。研究发现，NdFeB铸块在氢爆过程中明显存在孕育期，其吸氢过程分为四个阶段：孕育期阶段、慢速吸氢阶段、快速吸氢阶段和缓慢吸氢阶段；随着氢气压力(1～4atm)的升高，孕育时间缩短，吸氢越快；随着温度的升高，NdFeB铸块吸氢越迅速，当温度升至一定程度时，孕育期消失。扫描电镜观察发现，NdFeB合金氢爆破碎中的断裂方式包括沿晶和穿晶断裂，氢爆粉末尺寸小于50μm，取得了较好的氢爆效果。     

球铁铝锭模材料热疲劳性能的研究

模拟铝锭模的使用条件,研究了不同基体组织球墨铸铁的热疲劳性能.结果表明,退火铁素体铝铸锭模使用寿命最长.该铝锭模安装在包头铝业公司的2台铝锭连续铸造机上使用,平均每天铸锭48t/台,连续使用410天.而普通材质的球铁铝锭模使用寿命仅为120到150天左右.     

AgNO3浓度对SPE电极镀覆纳米Ag的影响

采用浸渍还原法(I-R法)在Nafion离子膜上镀覆纳米Ag,并就AgNO3浓度对SPE电极镀覆纳米银的影响作了研究.研究表明采用I-R法可制得细致Ag镀层,有效增加Ag的分散度及电极的真实面积.在还原剂浓度为0.1mol·L-1,浸渍还原温度均为50℃及浸渍还原时间分别为40 min,60 min的条件下,调节浸渍液AgNO3浓度至3.5 mmol·L-1时,可获得致密、均匀的纳米级Ag/SPE电极.同时验证砂纸糙化的预处理有利于增加Ag的负载和附着力,有利于提高Ag催化层的有效面积.     

改善银首饰铸造质量的措施

斯特林银首饰铸造时经常会出现气孔、缩孔、砂眼、氧化物夹杂等,其原因主要来自2个方面,一是在铸造过程中各工序的操作不当,尤其是水线的设置、开粉操作、焙烧制度等关键工序,必须加强操作过程的控制;二是与银本身的性质有关,银在凝固时氧的溶解度骤减,气体容易析出导致气孔;斯特林银主要以铜作为合金化元素,容易氧化形成夹杂。在熔炼或铸造过程中要尽量避免金属液接触大气,采用真空、或使用惰性气体、还原性火焰、硼酸等进行保护,可以减少铸造缺陷的发生。     

轴承保持架筒形坯件挤压铸造成形工艺及组织性能研究

采用直接挤压铸造成形工艺来生产Al-Cu系合金高速机床主轴轴承保持架筒形坯件，试验研究了其工艺参数对该铸件组织及力学性能的影响，从而确定出挤压铸造简形件合适的工艺参数。     

低温烧结SrBi4Ti4O15／Ag复合材料的制备及其介电特性

摘要：采用固相烧结工艺制备了SrBi4Ti4O15(SBTi)／Ag铁电复合材料，通过X射线衍射、光学金相显微镜和扫描电子显微镜对材料的组成和微观结构进行了研究，并测量样品的介电温度谱。结果表明：复合材料是由SBTi和Ag两相组成。微量金属Ag的加入使SBTi铁电陶瓷的烧结温度从1120℃降低到950℃以下：可以适当提高铁电陶瓷从室温到200℃的介电常数，但对材料的介电损耗影响很小。同时Ag的加入压抑了介电温度曲线上的介电常数的Curie峰。     

Ageing characteristics and microstructure of Al-4Mg-1.5Cu alloys containing silver and lithium

1　INTRODUCTIONTheroleoftraceelementsonageingofAlalloyshasbeenextensivelystudiedandhasbeenrecentlyre viewedbyPolmear ,RingerandPrabhuetal[14 ] .Itwasfoundthatthesmalladditionofsilvercanstimu lateenhancedagehardeningincertainAl Cu Mgal loys,andthiseffectisevidentforawiderangeofcompositionsselectedinthe (α +θ) ,(α +S)and (α+S +T ) phasefieldsoftheternary phasedia gram[57] .TheadditionofAgtoAl Cu MgalloyswithhighCutoMgratiosstimulatestheformationofanhexagonal shaped precipitate pha…     

Effect of ultrasonic stirring on temperature distribution and grain refinement in Al- 1.65%Si alloy melt

A series of experiments were conducted for Al-1.65%Si （mass fraction） alloy melt to study the formation of grain refining structure with ultrasonic stirring. The cooling curves of ingots with ultrasonic were measured and compared with those without ultrasonic. At the same time, the effect of the time of ultrasonic stirring on solidification structure of ingots was investigated. The influence of ultrasonic on the grain-refining efficiency of ingots was analyzed. In order to well understand the melts behavior under ultrasonic, by using ammonium chloride solution, the simulation experiment was carried out and the temperature distribution in ingot with or without ultrasonic was compared. The results indicate that the ultrasonic reduces the temperature inhomogeneity of melt, i.e. the ultrasonic helps to homogenize the melt temperature. The effect of stirring and heat generation in ingot start to occur with increasing the time of ultrasonic stirring.     

A novel electroless silver depositing method for magnesium alloys

Depositing silver on magnesium alloy by both electroless plating and organic coatings was studied. The organic coating was made by immersing samples in organosilicon heat-resisting varnish. In this method the organic coating acts as interlayer between the substrate and silver film. When the reaction starts, silver deposits directly on the interlayer. X-ray diffraction and SEM analysis were used to determine the composition and morphology of the interlayer and silver film. The potentiodynamic polarization curves for corrosion studies of coated magnesium alloys were performed in a corrosive environment of 3.5% NaCl（mass fraction） at neutral pH （6.9）. The results indicate that compared with the substrate, the corrosion resistance of coated magnesium alloys increases greatly. Moreover, the method proposed in this work is environmentally friendly, non-toxic chemicals were used. In addition, it provides a new concept for the corrosion inhibition of magnesium alloys.