Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

旋转导向钻井偏心稳定器横向振动研究

旋转导向钻井偏心稳定器横向振动研究是国家863“可控(闭环)三维轨迹钻井技术”课题研究的部分内容。选取偏心稳定器的心轴作为研究对象,以偏心稳定器心轴连续梁系统的横向振动模型受力分析为基础,根据课题研究中所设计的心轴结构形式,建立了与实际情况较为接近的三铰支点的连续梁系统横向振动方程;并分析了偏心稳定器横向振动对钻井工具和钻具系统的影响,为合理进行心轴设计以及偏心稳定器样机在现场的正确使用和钻井参数的合理选择,提供了科学的理论依据和实用的计算方法。计算实例表明,当钻压范围选择在80~250kN时,215.9mm井眼钻进中的确存在19~20、61~63、162~163r/min前三阶横向共振转速区间,因此在选择钻井参数时应通过钻压与转速的配合,尽可能避开横向共振转速,以保证下部钻具组合系统及作业安全。     

潜油电机碟形弹簧的动力学分析

为了降低潜油电泵机组的振动对止推轴承性能的影响,在潜油电机中节和下节的止推轴承静块底部安装了蝶形弹簧。用有限元方法进行模态分析,确定了蝶形弹簧的主振型和固有频率,然后进行瞬态动力学分析,求解蝶形弹簧在一定载荷下的应力和位移。依此设计的蝶形弹簧将进一步延长止推轴承的使用寿命。     

Total simulation model of the thermo-mechanical process in shape rolling of steel rods

The production of steel reinforcing bars for civil engineering is investigated by means of FEM-simulation. An integrated system for computing appropriate thermo-mechanical parameters of the rolling process is proposed. Generalized plane strain approach and coupled thermal-mechanical solution are applied. The microstructural model combines both the effect of the recrystallization mechanisms (static, dynamic and metadynamic) upon the austenite grain forming in hot rolling and that of phase transformation upon the final microstructure. The phases are created during interrupted below the temperature of martensite transition cooling. Thus a typical industrial process for thermo-mechanical strengthening of reinforcing bars, known as Tempcor-process is considered. Computational results are validated to experimental measured mechanical properties of the steel. By means of computer simulation the system can perform different solutions, giving the possibility to obtain a reasonable choice of different thermo-mechanical rolling conditions.     

空调器中多翼离心风机的噪声研究及结构优化

采用逐步回归法对大量的多翼离心风机实验数据进行拟合,针对家用空调行业中以噪声为其最重要 的考核标准,得出了噪声与叶轮结构参数及风机性能参数间的近似关系式,并以噪声为目标函数进行了优化计算。     

轧制力测量装置的使用与维护

简要论述了轧制力测量的基本原理，并从实际经验出发深入探讨了测压头的维护与管理要点。     

Preparation of clean coal by flotation following ultra fine liberation

This paper reports the results of current fundamental research at the Department of Process Engineering, University of Miskolc on the processing of clean coal from Mecsek bituminous coal, Southern Hungary. The theoretical possibility of the separation of different petrographic components was proven experimentally and their liberation degree was determined based on the petrographic composition, flotation kinetic study of isolated components (groups of components), scanning electron microscopy and microprobe analyses. The mill with stirred ball media was chosen for the ultra-fine liberation of the coal components. It was revealed that along with the liberation of coal components, their surface oxidation and spontaneous agglomeration, entrapping the mineral impurities take place in ultra-fine grinding. This paper discusses the interfacial phenomena occurring in the ultra-fine grinding process and their influence on the flotation. The concept for the advanced preparation of clean coal was developed, tested and proved. The main steps of this concept are the ultra-fine liberation in the stirred-media mill, the de-agglomeration of flocs spontaneously formed during the ultra-fine grinding and the induced (hydrophobic) flocculation with the following two-step flotation in a flotation column.     

A Theoretical Framework for Core Material Properties Identification in Cellular Solids using Novelty Detection

Abstract:  This paper presents a novelty detection-based technique to identify core material properties of honeycombs and cellular structures. A numerical model (finite element) representing full scale and/or reduced size of the cellular solid is used to generate transmissibilities between topological homologous points at cells in different locations. In order to make the procedure robust against noise, these transmissibilities are artificially corrupted. This step is representative of a series of experimentally obtained measurements which automatically return information relating to the size and shape of data noise along with the mean measurement. The next stage, both in this paper and in the proposal for the experimental approach, is to generate several further sets of transmissibilities from the finite element model; the only difference being that the core material properties are altered from the original values. A novelty detection framework is then adopted to find a similarity measure between each of these 'test' transmissibilities and the original set thereby identifying the material properties. Although this work is concerned with identifying only one material property, the methodology extends to identifying several properties.     

KMLS型立式砂泵的振动噪声产生原因及解决措施

针对KMLS型立式砂泵振动、噪声产生原因及其表现特征,提出了解决措施。通过对这些原因的分析研究,可以提供泵设计者和生产者在减少砂泵振动方面采取相应的措施,使KMLS型立式砂泵能更好的服务于用户。     

乳化型轧制液的质量标准研究

对国内目前所使用的冷轧薄钢板(汽车钢板)轧制液母液和乳化液的质量指标及常用试验评定方法进行了考察，并对产品的性能要求进行了研究与分析，制订出一套标准以供参考，包括乳化液稳定性、润滑性、防锈性、抗泡性、使用周期及粘度、闪点等性能。