自聚焦透镜用于端泵浦DPL的耦合光学系统

本文用自聚焦透镜耦合ＬＤ输出，解决了需要短焦距、大数值孔径透镜的设计和制方面的困难。提出了计算自聚焦透镜耦合效率的简化模型。用自聚焦透镜和一对正交柱面透镜设计了一个耦合系统，并用该耦合系统端泵浦Ｎｄ：ＹＡＧ棒做了实验。     

Σ-Δ过抽样转换器使用中的注意事项

为了充分发挥Σ Δ过抽样转换器的能力以获得最佳的系统性能 ,文章在分析直流电压、时钟抖动及电源的杂波等诸多因素对其影响的基础上 ,提出了适于Σ Δ过抽样转换器工作的最佳条件 ,对Σ Δ过抽样转换器系统的设计制作与调试有一定的指导意义     

甲烷和乙烷共同转化制乙烯的研究

甲烷和乙烷可以同时在Ｗ－Ｍｎ／ＳｉＯ２催化剂上得到活化生成乙烯。原料乙烷和甲烷体积比在０．１１～０．２５的范围内，当甲烷转化率为２０％左右时，共进料反应产物中乙烯体积浓度为８％～１２％，达到炼油厂催化裂化干气中乙烯的浓度。     

1.30μmDFB激光器组件的设计和制做及其工作原理

本文自行设计和制作了１．３０μｍＤＦＢ激光器组件的讨论了光隔离和光耦合原理。由于采用的激光器－光隔离器－光纤的一体化结构，大大增加了该组件的可用性。在实验中得到高达５５％的耦合效率。     

A FETI-like domain decomposition method for coupling finite elements and boundary elements in large-size problems of acoustic scattering

Numerical simulations of acoustic scattering in the frequency domain based on hybrid methods coupling finite elements and boundary elements are the most suited for dealing with problems involving wave propagation in inhomogeneous media. Furthermore, it is necessary to resort to high performance computing to effectively solve the large size problems. However, the direct coupling yields a linear system with a matrix which is partly dense and partly sparse and thus not adapted to high performance computing. To avoid this difficulty, we present a new iterative method constructed from a non overlapping domain decomposition technique.     

Miniaturization and bandwidth enhancement of a cavity backed circular microstrip patch antenna

The resonant frequency of a circular patch antenna with and without circular cavity is measured. The patch miniaturization in the presence of the cavity is proved. Different methods of reducing resonant frequencies and broadening bandwidth without significantly reducing antenna gain are presented. Capacitively loaded patch and slits on the patch stimulate the patch at lower frequencies and multiple resonances, thus help miniaturization. Finally ferrite loading on the feed probe further increases the bandwidth without significantly reducing the antenna gain. The method is much more improved than that for a resistive loaded patch and a deformed patch. © 2007 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2007.     

万安水利枢纽底孔坝段中隔墙流激振动响应分析

 研究了万安水利枢纽底孔坝段中隔墙在水流脉动壁压作用下的结构随机振动问题，进行了一种泄流工况下的隔墙结构流激振动响应统计量的理论计算，模拟计算了隔墙－水流－基础耦合系统固有频率对流激振动响应的影响，并对水流脉动壁压随机荷载作用下的结构动力可靠度进行了理论分析。     

偶联剂对玻璃纤维/环氧基复合材料界面介电性能的影响研究

本文研究了五种偶联剂对玻璃纤维浸润性能和玻璃纤维/环氧基复合材料界面介电性能的影响。结果表明,玻璃纤维经偶联剂处理后,其浸润活化能降低,与环氧树脂基体间的相容性及化学反应活性得到改善;因此赋予了玻璃纤维与环氧基体间以良好的界面粘结性能,从而提高了玻璃纤维/环氧基复合材料界面的介电性能。其提高的幅度大小与偶联剂的极性及化学结构有关。     

The result of a wall failure in-pile experiment under the EAGLE project

The WF (wall failure) test of the EAGLE program, in which 2 kg of uranium dioxide fuel-pins were melted by nuclear heating, was successfully conducted in the IGR (Impulse Graphite Reactor) of NNC/Kazakhstan. In this test, a 3 mm-thick stainless steel (SS) wall structure was placed between fuel pins and a 10 mm-thick sodium-filled channel (sodium gap). During the transient, fuel pins were heated, which led to the formation of a fuel-steel mixture pool. Under the transient nuclear heating condition, the SS wall was strongly heated by the molten pool, leading to wall failure. The time needed for fuel penetration into the sodium-filled gap was very short (less than 1 s after the pool formation). The result suggests that molten core materials formed in hypothetical LMFBR core disruptive accidents have a certain potential to destroy SS-wall boundaries early in the accident phase, thereby providing fuel escape paths from the core region. The early establishment of such fuel escape paths is regarded as a favorable characteristic in eliminating the possibility of severe re-criticality events. A preliminary interpretation on the WF test results is presented in this paper.     

塑料合金高弹性联轴器试验台的开发研究

对塑料合金高弹性联轴器的综合性能试验台进行了设计，阐述试验台的设计要求、设计思想和结构特点，并介绍试验台的总体布局和组成部分；液压系统是试验台的核心部分，重点对液压系统进行设计及说明。