第三代蜂窝网络核心网的QoS技术分析

介绍了3G核心网的服务质量保证问题。按照网络实体和3G演进的版本分别对核心网的QoS保证技术进行了重点分析,并与有线网络的QoS保证方案的特点进行对比,分析了3G网络R5版本在QoS方面遇到的问题。     

3G网络规划中TD-SCDMA与WCDMA的互干扰

3G网络在中国市场商用的决定性时刻已离我们越来越近,但是,主流的三大协议标准由于其技术标准与营运氛围各不相同,势必会带来频率间相互干扰的问题,甚至与现行的CDMA、GSM和PCS网络都会有互干扰问题的出现.文章从数学角度分析了TD-SCDMA与WCDMA在网络规划时的互干扰问题和解决构思.     

基于互信息域的L2S接口方法研究

分析了基于互信息域的有效信噪比映射的L2S(link level to system level)接口方法,研究了信道相关带宽对接口复杂度的影响,在不明显降低预测准确度的前提下,验证了利用信道相关带宽来简化接口计算复杂度的可能性。     

Al2O3对唐钢高炉炉渣性能的影响

针对唐钢近2年提高进口矿配比后，Al2O3含量升高对炉渣流动性带来的不利影响，对唐钢高炉的炉渣性能进行了试验研究。并结合国内同行业的生产实践经验，从理论上分析了炉渣中Al2O3及MgO的适宜含量范围，着重论述了唐钢所处冀东矿区条件下降低Al2O3的主要途径及适应高Al2O3炉渣的具体措施。     

聚合物凝胶用Cr3+交联剂检测方法探讨

胜利油田交联聚合物驱、封堵大孔道中使用Cr3+交联的HPAM凝胶。探讨了Cr3+交联剂的检测方法。将4种商品HPAM和6种商品Cr3+交联剂在矿化度5727mg/L、钙镁含量108mg/L的胜利盐水中配制成24个HPAM/Cr3+成胶溶液,根据70℃下反应72h后在70℃测定的凝胶相对强度(要求在代码C以上),确定使用分子量1.11×107、水解度28.8%的一种HPAM,配液浓度为1300mg/L。推荐采用在70℃、振荡频率f=0.422s-1测定的复数粘度η 和储能模量G′表示凝胶的强度,给出了HPAM浓度不同、各Cr3+交联剂浓度为最低需要量的6种凝胶的η 和G′值;推荐取G′值达到0.1Pa的时间为成胶时间,由上述6种体系的G′ t曲线求出成胶时间在98～300min范围。提出其他应测定的性能包括:成胶溶液抗剪切性,凝胶热稳定性(抗热老化性),凝胶抗温性,凝胶抗盐性及岩心堵水率,对测定方法作了详略不等的讨论。特别指出,用于热老化实验的成胶溶液必须彻底除氧,否则粘时曲线的变化将无规律(给出了实例)。图7表7参3。     

Development of intelligent multisensor surveillance systems with agents

Intelligent multisensor surveillance systems consist of several types of sensors, which are installed on fixed and mobile devices. These components provide a huge quantity of information that has to be contrasted, correlated and integrated in order to recognize and react on special situations. These systems work in highly dynamic environments, with severe security and robustness requirements. All these characteristics imply the need for distributed solutions. In these solutions, scattered components can decide and act with some degree of autonomy (for instance, if they become isolated), or cooperate and coordinate for a complete tracking of special situations. In order to cope with these requirements and to better structure the solution, we have decided to design surveillance system control as a multiagent system. This is done by applying an agent-orientated methodology, which is assessed with concrete scenarios.     

地层测试对油层改造选井选层的重要性及改造措施有效性评价

经对胜利油田近三年来典型井例测试资料分析评价及其增产措施效果分析认为，有三类地层压裂增油效果很好：地层物性相对较好的常压系统且存在严重堵塞的储层；物性较好的常压地层；高压低渗透储层。有两类地层酸化效果很好：灰岩、白云岩裂缝、低产低渗透储层；物性较好且存在严重污染堵塞的储层。其它地层压裂、酸化一般是无效的。     

一种精密温度控制仪

采用精密温度补偿及在传统PID调节基础上运用模糊控制运算 ,实现以单片机为基础开发研制的精密温度控制仪 ,并输出时间开关量信号和 4～ 2 0mA标准电流信号 ,为闭环控制及温度值远传提供依据。     

Determination of the content of wax esters in some sea foods and their molecular composition. A comparison with ω-3 enriched wax esters

Wax esters enriched in ω-3 fatty acids have been recently shown to be readily absorbed by rats after dietary supplementation. Wax esters are less prone to oxidation and can be better formulated than liquid ω-3 derivatives. All these characteristics suggest a possible use of wax esters enriched in ω-3 as food supplements. However, some naturally occurring wax esters are defined as scarcely digestible (jojoba oil, spermaceti). On the other hand, wax esters have been found in several sources of marine origin, which can enter normal foodstuff. In order to better understand the digestibility of wax esters, we have analysed some foods from marine sources. The content of triglycerides and wax esters of the foods has been determined. Moreover, wax esters have been analysed for their composition in alcohols and fatty acids. Wax esters have been shown to be a part of the neutral lipid extract of the foods analysed. Their content, if compared with the content in triglycerides, shows striking differences. In the case of two botargo preparations, it has been shown that wax esters are more than 90% of the total neutral lipid extract. The content of fatty acids and alcohols found in the foods analysed is consistent with published data.     

Effect of 3D lip deformations on elastohydrodynamic lip seals behaviour

The numerical simulation of comparative elastohydrodynamic lubrication between axisymmetrical and 3D elastic approaches on the radial lip seals is presented in order to determine the 3D effect of the elastic aspect of the seal lip. Indeed, the consideration of 3D model in other words the circumferential variation of the lip elastic deformation indicated a difference in the deformation distribution of the lip compared to the axisymmetrical approach. Consequently, the results show that the presence of the circumferential variation of the seal lip deformation has a significant effect on the pumping rate values.