转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

分流液压转向牵引计算的展开图及其应用

本文论及分流液压转向牵引计算的概念,方法及其展开图,并且提供了计算机绘制的展开图和应用实例。     

An analytical expression for the power coefficient of an ideal horizontal-axis wind turbine

The paper shows that an analytical evaluation of the power coefficient C_p for an ideal horizontal-axis wind turbine can be made via an expression giving the direct relationship of C_p and the axial induction factor a. The results obtained agree closely with those obtained numerically from the usual integral expression involving several variables.     

Lifetime control in silicon power P-i-N diode by ion irradiation: Suppression of undesired leakage

The irradiation with high-energy (7.35 MeV) protons through a set of energy degraders was used to suppress leakage of the silicon power diodes subjected to local lifetime control. The aim was to modify the profile of recombination centers and to reduce production of vacancy complexes. The high-energy proton irradiation was compared with standard local lifetime killing by high-energy alphas. Recombination centers arising from irradiation were characterized after irradiation and subsequent annealing at 220 and 350 °C by deep level transient spectroscopy and I-V profiling. Static and dynamic parameters of irradiated diodes were also measured and compared. Results show that the applied irradiation with protons provides 3-10 times lower leakage compared to standard alphas for equivalent reduction of the reverse recovery current maximum. On the other hand, the excessive formation of hydrogen donors at high proton fluences and their diffusion during annealing at 350° decreases diode blocking capability.     

A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

Design and evaluation of an active electromechanical wheel suspension system

This paper presents an electromechanical wheel suspension, where the upper arm of the suspension has been provided with an electric levelling and a damper actuator, both are allowed to work in a fully active mode. A control structure for the proposed suspension is described. The complex design task involving the control of the electric damper and its machine parameters is tackled by genetic optimisation. During this process, these parameters are optimised to keep the power dissipation of the electric damper as low as possible, while maintaining acceptable comfort and road-holding capabilities. The results of the evaluations carried out demonstrate that the proposed suspension can easily adopt its control parameters to obtain a better compromise of performance than that offered by passive suspensions. If the vehicle is to maintain acceptable performance during severe driving conditions, the damper has to be unrealistically large. However, if the electric damper is combined with a hydraulic damper, the size of the electric damper is significantly reduced. In addition, the design of the electric damper with the suggested control structure, including how it regenerates energy, is discussed.     

回转窑供电装置改造

本阐述了回转窑供电装置存在的缺陷，亦即改造过程和改造后的效果。     

Laboratory simulated slipstream testing of novel sulfur removal processes for gasification application

The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project is investigating an Early Entrance Coproduction Plant (EECP) concept to evaluate integrated electrical power generation and methanol production from coal and other carbonaceous feedstocks. Research, development and testing (RD&T) that is currently being conducted under the project is evaluating cost effective process systems for removing contaminants, particularly sulfur species, from the generated gas which contains mainly synthesis gas (syngas), CO₂ and steam at concentrations acceptable for the methanol synthesis catalyst. The RD&T includes laboratory testing followed by bench-scale and field testing at the SG Solutions Gasification Plant located in West Terre Haute, Indiana. Actual synthesis gas produced by the plant was utilized at system pressure and temperature for bench-scale field testing.