不同金属硫化物从钨酸盐溶液中除钼的效果

针对钨冶炼过程中钨钼分离这一关键问题,研究了利用CuS,CoS,NiS,PbS,FeS,ZnS和HgS等金属硫化物从钨酸盐溶液中除钼的效果.对含钼的Na2WO4或(NH4)2WO4溶液用Na2S或(NH4)2S 进行硫化处理,使其中的MoO2-4转化为MoS2-4,然后加入上述金属硫化物进行除钼.结果表明,CuS,CoS和NiS在Na2WO4或(NH4)2WO4溶液中均具有良好的除钼效果,综合考虑经济、环保等因素,认为CuS是最经济合理的钨钼分离新试剂.考察了试剂用量、反应温度和溶液pH值对除钼效果的影响,并获得了最佳除钼工艺条件,即在CuS试剂用量为理论量的3～4倍、室温下搅拌反应1h的条件下,可使溶液中的Mo从0.6～0.77g/L降至0.007～0.02g/L,除钼率达96.0%～98.5%,整个除钼过程中钨的回收率达99.75%以上.     

不锈钢板冷轧机的现状和发展

简要叙述不锈钢板冷轧机（20辊森吉米尔轧机、四柱式2O辊轧机、12辊CR轧机等）的结构特点、发展概况及各自采用的先进控制系统。     

时效对Au－39．8Cu－21．0Zn－3．2Al形状记忆合金的影响

用电阻法研究了不同时效条件对标题合金的马氏体转变温度和形状记忆效应的影响。结果表明：经分级淬火处理的合金，有较高的热稳定性和良好的形状记忆效应。但在高于１２０℃的温度时效一定时间后，将严重影响合金的马氏体相变，从而使合金丧失形状记忆效应。     

装饰用梅花形黄铜管拉伸成型工艺研究

通过对梅花形黄铜管一次拉伸成型的实验 ,研究了管坯的规格、管坯的状态、延伸系数、拉伸方式、工艺润滑及拉伸速度等工艺因素对梅花黄铜管凸筋高度充填的影响规律 ,这些结论对实际生产有一定的指导意义。     

Analysis of the thermal expansion characteristics of Ni53.6Mn27.1Ga19.3 alloy

Dilatation characteristics of Ni_53.6Mn_27.1Ga_19.3 alloy were measured in the temperature range of 20–360 °C. The coefficient of thermal expansion (CTE) decreased with increasing temperature in the temperature range of the existence of martensite. Three variants of martensite transformed gradually into austenite. Analysis of the dilatation characteristics showed that compression deformation of the alloy at room temperature produces two kinds of strain.     

模锻件切边凹模刃口形状探讨

通过对模锻件切边过程与定位要求的描述，对切边凹模刃口形状与模锻件飞边桥部关系的分析，并基于实践经验，指出对于非平面分模锻件和水平投影轮廓形状复杂的锻件，切边凹模刃口形状不宜完全按(热)锻件分模面轮廓制造，而应针对锻件具体结构作一些调整。     

铁基形状记忆合金（待续）

简介形状记忆效应(SME)的基本概念和形状记忆合金的发展。评述了Fe-Mn-Si,Fe-Mn-Si-Cr-Ni,Fe-Ni-Co-Ti和Fe-Ni-C等系铁基形状记忆合金的生长背景,特性及其SME的机制。     

急弯段闸孔出流的弯道水流特性研究

在河弯处修建水工建筑物时,研究弯道水流特性对水工建筑物布置的影响十分重要。采用RNCκ-ε紊流模型对急弯段闸孔出流的弯道水流进行了三维数值模拟。通过模拟计算,比较分析了急弯段不同闸位、不同流量条件下闸孔过流时的流速分布、紊流动能、压强分布和环流等相关水流特性与变化规律。分析研究结果表明,闸坝位于弯道上游时,弯道对闸坝过流的影响最小,但需对闸坝下流弯道凸岸岸坡附近区域采取一定的防护措施;闸坝布置在弯道中游时,过闸水流受弯道的影响最小,闸室水流的稳定性、闸门的工作安全以及闸墩的空蚀破坏都是实际工程中需要注意的重点。数值模拟验证与物理模型试验结果吻合较好,计算精度较高,能够满足相关计算研究要求。     

Single-view-based 3D facial reconstruction method robust against pose variations

The 3D Morphable Model (3DMM) and the Structure from Motion (SfM) methods are widely used for 3D facial reconstruction from 2D single-view or multiple-view images. However, model-based methods suffer from disadvantages such as high computational costs and vulnerability to local minima and head pose variations. The SfM-based methods require multiple facial images in various poses. To overcome these disadvantages, we propose a single-view-based 3D facial reconstruction method that is person-specific and robust to pose variations. Our proposed method combines the simplified 3DMM and the SfM methods. First, 2D initial frontal Facial Feature Points (FFPs) are estimated from a preliminary 3D facial image that is reconstructed by the simplified 3DMM. Second, a bilateral symmetric facial image and its corresponding FFPs are obtained from the original side-view image and corresponding FFPs by using the mirroring technique. Finally, a more accurate the 3D facial shape is reconstructed by the SfM using the frontal, original, and bilateral symmetric FFPs. We evaluated the proposed method using facial images in 35 different poses. The reconstructed facial images and the ground-truth 3D facial shapes obtained from the scanner were compared. The proposed method proved more robust to pose variations than 3DMM. The average 3D Root Mean Square Error (RMSE) between the reconstructed and ground-truth 3D faces was less than 2.6 mm when 2D FFPs were manually annotated, and less than 3.5 mm when automatically annotated.