Impedance matching optimization of SiCf/Si3N4–SiOC composites for excellent microwave absorption properties

SiC fiber reinforced ceramic matrix composites (SiC_f-CMCs) are considered to be one of the most promising materials in the electromagnetic (EM) stealth of aero-engines, which is expected to achieve strong absorption and broad-band performance. Multiscale structural design was applied to SiC_f/Si₃N₄–SiOC composites by construction of micro/nanoscale heterogeneous interfaces and macro double-layer impedance matching structure. SiC_f/Si₃N₄–SiOC composites were fabricated by using SiC fibers with different conductivities and SiOC–Si₃N₄ matrices with gradient impedance structures to improve impedance matching effectively. Owing to its unique structure, SiC_f/Si₃N₄–SiOC composites (A3-composites) achieved excellent EM wave absorption performance with a minimum reflection coefficient (RC_min) of ?25.1 dB at 2.45 mm and an effective absorption bandwidth (EAB) of 4.0 GHz at 2.85 mm in X-band. Moreover, double-layer SiC_f/Si₃N₄–SiOC with an improved impedance matching structure obtained an RC_min of ?56.9 dB and an EAB of 4.2 GHz at 3.00 mm, which means it can absorb more than 90% of the EM waves in the whole X-band. The RC is less than ?8 dB at 2.6–2.8 mm from RT to 600 °C in the whole X-band, displaying excellent high-temperature absorption performance. The results provide a new design opinion for broad-band EM absorbing SiC_f-CMCs at high temperatures.     

Polarity Effect and Electromagnetic Radiation of Partial Discharge Accompanying Growth of Electrical Tree

We have investigated the characteristics of radiated electromagnetic (EM) waves from positive and negative partial discharges (PD) in epoxy resin and cross‐linked polyethylene. We found that there is a correlation among the EM level from PD, the positive PD current, and electrical trees. Therefore, the growth of an electrical tree produces a lot of positive PD. We have also investigated the characteristics of the frequency region of EM waves from PD in air, insulating oil, and liquid epoxy in addition to the above insulators. EM waves were detected in the frequency region of 40 MHz to 300 MHz from positive and negative PD in epoxy resin and cross‐linked polyethylene. EM waves were also detected in the frequency region of 40 MHz to 150 MHz from positive and negative PD in air. In the case of insulating oil and liquid epoxy, EM waves were detected in the frequency regions of 40 MHz to 150 MHz from positive PD, and 40 MHz to 250 MHz from negative PD. The frequency region differed depending on the material and the discharge polarity. Our investigation indicates that the cause is differences in electric field strength at the time of PD occurrence.     

Impact sensitivities of energetic materials: Exploring the limitations of a model based only on structural formulas

Using a comprehensive set of drop weight impact test data (h₅₀) newly compiled from literature for 308 materials, a recent approach to predict impact sensitivities of nitro compounds is generalized to most explosive substances of interest. Compared to previous ones, this procedure is more thoroughly validated and exhibits a good predictive value. Furthermore, it yields new insight into the physical mechanisms involved, explaining for instance the unexpected desensitization of some oxygen-deficient triazoles upon nitration.     

A Reduced Reachability Tree for a Class of Unbounded Petri Nets

As a powerful analysis tool of Petri nets, reachability trees are fundamental for systematically investigating many characteristics such as boundedness, liveness and reversibility. This work proposes a method to generate a reachability tree, called ωRT for short, for a class of unbounded generalized nets called ω-independent nets based on new modified reachability trees (NMRTs). ωRT can effectively decrease the number of nodes by removing duplicate and ω-duplicate nodes in the tree, and verify properties such as reachability, liveness and deadlocks. Two examples are provided to show its superiority over NMRTs in terms of tree size.      

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

The influence of processing conditions on the mechanical properties of poly(aryl-ether-ketone)/polybenzimidazole blends

Interest in developing high-performance blends for niche applications has grown significantly in efforts to meet ever-increasing harsh environment demands. In this work, four model poly(aryl-ether-ketone)/polybenzimidazole (PAEK/PBI) blends were chosen to study the influence of premixing methods, processing, and matrix polymers, on their mechanical properties. Among the model poly(ether ether ketone) (PEEK) and PBI blends, mechanical properties are greatly enhanced by melt premixing. The molding process mainly affects the matrix crystallinity, which in turn greatly influences fracture toughness of the blend. Poly(ether ketone ketone) (PEKK) and PBI blend exhibits a slightly lower tensile strength and fracture toughness than PEEK/PBI due to the differences in inherent properties of PEEK and PEKK matrices and their interfacial interaction with PBI. The processing−structure–property relationship of PAEK/PBI blends is established to help guide optimal design of high-performance polymer blends for structural applications. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48966.     

PMU based voltage security assessment of power systems exploiting principal component analysis and decision trees

The need for feature selection and dimension reduction is felt as a fundamental step in security assessment of large power systems in which the number of features representing the state of power grids dramatically increases. These large amounts of attributes are not proper to be used for computational intelligence (CI) techniques as inputs, because it may lead to a time consuming procedure with insufficient results and they are not suitable for on-line purposes and updates.This paper proposes a combined method for an online voltage security assessment in which the dimension of the token data from phasor measurement units (PMUs) is reduced by principal component analysis (PCA). Then, the features with different stability indices are put into several categories and feature selection is done by correlation analysis in each category. These selected features are then given to decision trees (DTs) for classification and security assessment of power systems.The method is applied to 39-bus test system and a part of Iran power grid. It is seen from the results that the DTs with reduced data have simpler splitting rules, better performance in saving time, reasonable DT error and they are more suitable for constant updates.     

汽车雨挡导流片浮顶式侧抽芯机构注射模设计

介绍了一款汽车雨挡导流片异型塑件两板注射模的结构设计,该模具基于采用常规的滑块抽芯机构及斜顶机构难以实现塑件完全脱模的机构设计困难问题,突破常规设计思路,设计了一种型芯浮顶式侧抽芯机构来实现塑件的自动化注射生产。机构中,在模具开模打开后,通过顶出板及顶杆将塑件和部分成型一同顶出,而后再通过侧边二次顶出机构将塑件从局部型芯上顶出而实现塑件的完全脱模,有效地简化了模具结构设计,降低了模具的加工制造难度,降低了模具的制造成本,模具结构复杂新颖,工作稳定可靠,为异型类塑件的模具结构及机构设计创新设计提供了一个较好的案例借鉴。