Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.     

Effects of structural characteristics on microwave dielectric properties of low-loss (Zn1-xNix)ZrNbTaO8 ceramics

Low-loss (Zn_1-xNi_x)ZrNbTaO₈ (0.02?≤?x?≤?0.10) ceramics possessing single wolframite structure are initiatively synthesized by solid-state route. Based on the results of Rietveld refinement, complex chemical bond theory is used to establish the correlation between structural characteristics and microwave performance in this ceramic system. A small amount of Ni²⁺ (x?=?0.06) in A-site with the fixed substitution of Ta⁵⁺ in B-site can effectually raise the Q?×?f value of ZnZrNb₂O₈ ceramic, embodying a dense microstructure and high lattice energy. The dielectric constant and τ_f are mainly affected by bond ionicity and the average octahedral distortion. The (Zn_0.94Ni_0.06)ZrNbTaO₈ ceramic sample sintered at 1150?°C for 3?h exhibits an outstanding combination of microwave dielectric properties: ε_r =?27.88, Q?×?f?=?128,951?GHz, τ_f =?–39.9?ppm/°C. Thus, it is considered to be a candidate material for the communication device applications at high frequency.     

Identification of digital technologies and digitalisation trends in the mining industry

Digitalisation in mining refers to the use of computerised or digital devices or systems and digitised data that are to reduce costs, improve business productivity, and transform mining practices. However, it remains increasingly difficult for mining companies to decide which digital technologies are most relevant to their needs and individual mines. This paper provides an overview of digital technologies currently relevant to mining companies as presented and discussed by mining journals, the media and insight reports of leading consultancy agencies. Relevant technologies were systematically identified using text-mining techniques, and network analyses established the relations between significant technologies. Results demonstrated that currently 107 different digital technologies are pursued in the mining sector. Also, an analysis of the actual implementation of digital technologies in 158 active surface and underground mines reveals a limited uptake of digital technologies in general and that the uptake increases with the run-of-mine production. Large-scale mining operations appear to select and apply digital technologies suitable to their needs, whereas operations with lower production rates do not implement the currently available digital technologies to the same extent. These minor producers may require other digital transformation solutions tailored to their capabilities and needs and applicable to their scale of operations.     

Evaluation of expanded gamut software solutions for spot color reproduction

Expanded gamut printing is an approach in color reproduction that expands the color gamut of conventional CMYK printing processes via the use of additional colorants, such as Orange, Green, and Violet inks. This study evaluates the ability of commercial color management software to create an accurate solution for an expanded gamut printing system. In this study, two printing processes were used, an Epson SureColor P9000 inkjet printer/proofer and an HP Indigo 7900 digital production press, both with 7-color expanded gamut ink sets. Software solutions from Alwan, CGS ORIS, ColorLogic, GMG Color, Heidelberg, and Kodak were evaluated. The systems were tested to see how well they could reproduce the colors in the entire PANTONE+ Solid Coated spot color library. It is shown that the solutions are able to reproduce 89% to 94% of the spot colors on the Epson P9000 inkjet printer and 77% to 87% of the library on the Indigo 7900, both to less than two CIEDE2000 (a typical tolerance in label and packaging work). The number of color patches in expanded gamut characterization test charts was noted, as this is still an area of proprietary, nonstandardized working practice. There are many different colorant combinations that can make the same color in expanded gamut printing. The ink build created by the different software solutions was studied, as it relates to press stability through appropriate choice of colorants. Pantone and Adobe provide everyday commercial tools for expanded color workflows. The study identified some issues with products from these companies that could confuse a less-skilled user in a busy production environment. The conclusion of the study is that expanded gamut solutions for spot color printing produce totally acceptable results for digital printing processes; expanded gamut printing is ready, here and now. The findings show that expanded gamut printing can replace cumbersome conventional spot color workflows creating considerable savings and advantages, especially for label and packaging printers.     

Design structure matrix (DSM) method application to issue of modeling and analyzing the fault tree of a wind energy asset

The perpetual energy production of a wind farm could be accomplished (under proper weather conditions) if no failures occurred. But even the best possible design, manufacturing, and maintenance of a system cannot eliminate the failure possibility. In order to understand and minimize the system failures, the most crucial components of the wind turbines, which are prone to failures, should be identified. Moreover, it is essential to determine and classify the criticality of the system failures according to the impact of these failure events on wind turbine safety. The present study is processing the failure data from a wind farm and uses the Fault Tree Analysis as a baseline for applying the Design Structure Matrix technique to reveal the failure and risk interactions between wind turbine subsystems. Based on the analysis performed and by introducing new importance measures, the “readiness to fail” of a subsystem in conjunction with the “failure riskiness” can determine the “failure criticality.” The value of the failure criticality can define the frame within which interventions could be done. The arising interventions could be applied either to the whole system or could be focused in specified pairs of wind turbine subsystems. In conclusion, the method analyzed in the present research can be effectively applied by the wind turbine manufacturers and the wind farm operators as an operation framework, which can lead to a limited (as possible) design‐out maintenance cost, failures' minimization, and safety maximization for the whole wind turbine system.     

Application of the novel Droplet digital PCR technology for identification of meat species

The authenticity and traceability of meat products are issues of primary importance to ensure food safety. Unfortunately, food adulteration (e.g. the addition of inexpensive cuts to minced meat products) and mislabelling (e.g. the inclusion of meat from species other than those declared) happens frequently worldwide. The aim of this study was to apply a droplet digital PCR assay for the detection and quantification (copies μL⁻¹) of the beef, pork, horse, sheep, chicken and turkey in meat products. The analysis conducted on commercial meat showed the presence of traces of DNA from other animal species than those declared. We show that the method is highly sensitive, specific and accurate (accuracy = 100%). This method could be adopted by competent food safety authorities to verify compliance with the labelling of meat products and to ensure quality and safety throughout the meat supply chain, from primary production to consumption.     

Application of Vis–NIR hyperspectral imaging in classification between fresh and frozen-thawed pork Longissimus Dorsi muscles

Fresh and frozen-thawed (F-T) pork meats were classified by Vis–NIR hyperspectral imaging. Eight optimal wavelengths (624, 673, 460, 588, 583, 448, 552 and 609 nm) were selected by successive projections algorithm (SPA). The first three principal components (PCs) obtained by principal component analysis (PCA) accounted for over 99.98% of variance. Gray-level-gradient co-occurrence matrix (GLGCM) was applied to extract 45 textural features from the PC images. The correct classification rate (CCR) was employed to evaluate the performance of the partial least squares-discriminate analysis (PLS-DA) models, by using (A) the reflected spectra at full wavelengths and (B) those at the optimal wavelengths, (C) the extracted textures based on the PC images, and (D) the fused variables combining spectra at the optimal wavelengths and textures. The results showed that the best CCR of 97.73% was achieved by applying (D), confirming the high potential of textures for fresh and F-T meat discrimination.     

Static stress analysis of carbon nano-tube reinforced composite (CNTRC) cylinder under non-axisymmetric thermo-mechanical loads and uniform electro-magnetic fields

Static stresses analysis of carbon nano-tube reinforced composite (CNTRC) cylinder made of poly-vinylidene fluoride (PVDF) is investigated in this study. Non-axisymmetric thermo-mechanical loads are applied on cylinder in presence of uniform longitudinal magnetic field and radial electric field. The surrounded elastic medium is modeled by Pasternak foundation because of its advantages to the Winkler type. Distribution of radial, circumferential and effective stresses, temperature field and electric displacements in CNTRC cylinder are determined based on Mori–Tanaka theory. The detailed parametric study is conducted, focusing on the remarkable effects of magnetic field intensity, elastic medium, angle orientation and volume fraction of carbon nano-tubes (CNTs) on distribution of effective stress. Results demonstrated that fatigue life of CNTRC cylinder will be significantly dependent on magnetic intensity, angle orientation and volume fraction of CNTs. Results of this research can be used for optimum design of thick-walled cylinders under multi-physical fields.     

数字储频及其性能分析

文章介绍了3种宽带数字储频的基本结构，分析了宽带数字储频的一个重要指标——量化噪声，根据输出信号频谱的杂散电平比较了三种结构的优劣。     

数字化蓄热式钢包烘烤器及自动控制系统

蓄热式燃烧技术和脉冲燃烧技术是新型的节能环保燃烧技术。数字化蓄热式钢包烘烤器控制系统利用数字化脉冲控制把这两项技术结合在一起。这大大降低了能耗，减少环境污染。本文针对数字化蓄热式钢包烘烤器，提出升温阶段采用自寻优算法，不断调整换向时间，并能记忆最优参数，保证经过几次烘烤后系统整体最优；保温阶段即采用脉冲控制的方法。