Mitochondrial Bioenergetic,Photobiomodulation and Trigeminal Branches Nerve Damage,What’s the Connection? A Review

Background: Injury of the trigeminal nerve in oral and maxillofacial surgery can occur. Schwann cell mitochondria are regulators in the development, maintenance and regeneration of peripheral nerve axons. Evidence shows that after the nerve injury, mitochondrial bioenergetic dysfunction occurs and is associated with pain, neuropathy and nerve regeneration deficit. A challenge for research is to individuate new therapies able to normalise mitochondrial and energetic metabolism to aid nerve recovery after damage. Photobiomodulation therapy can be an interesting candidate, because it is a technique involving cell manipulation through the photonic energy of a non-ionising light source (visible and NIR light), which produces a nonthermal therapeutic effect on the stressed tissue. Methods: The review was based on the following questions: (1) Can photo-biomodulation by red and NIR light affect mitochondrial bioenergetics? (2) Can photobiomodulation support damage to the trigeminal nerve branches? (preclinical and clinical studies), and, if yes, (3) What is the best photobiomodulatory therapy for the recovery of the trigeminal nerve branches? The papers were searched using the PubMed, Scopus and Cochrane databases. This review followed the ARRIVE-2.0, PRISMA and Cochrane RoB-2 guidelines. Results and conclusions: The reliability of photobiomodulatory event strongly bases on biological and physical-chemical evidence. Its principal player is the mitochondrion, whether its cytochromes are directly involved as a photoacceptor or indirectly through a vibrational and energetic variation of bound water: water as the photoacceptor. The 808-nm and 100 J/cm² (0.07 W; 2.5 W/cm²; pulsed 50 Hz; 27 J per point; 80 s) on rats and 800-nm and 0.2 W/cm² (0.2 W; 12 J/cm²; 12 J per point; 60 s, CW) on humans resulted as trustworthy therapies, which could be supported by extensive studies.     

Effects of short carbon fiber on the macro-properties,mechanical performance and microstructure of SiSiC composite fabricated by selective laser sintering

Selective laser sintering was combined with reactive melt infiltration to fabricate SiSiC part, and the effects of carbon fiber (C_f) on the properties of the SLS green body, the carbonized and final SiSiC sample were investigated. Results show that the addition of an appropriate amount of C_f (1.59 wt%~2.97 wt%) can increase the bulk density and geometric precision of the sample at all stages, and improve the mechanical properties of green and carbonized samples. The main phases composed of the SiSiC composite were free Si, a-SiC, β-SiC, plus a very small amount of Al–Si alloy. With 1.59 wt% C_f addition, a relatively comprehensive favorable macro-properties of both the green sample and carbonized sample was achieved, and the homogeneous microstructure of the latter favored the decreased free Si content and increased β-SiC content of the final composite. The evolution mechanism of C_f added to the raw material is inferred to be the mutual diffusion of [C] and [Si] that occurred at the C_f/Si melt boundary leading to the formation of the siliconized C_f with relatively large diameter size (24.3 μm) and high aspect ratio (>30). Amorphous C, which derived from the pyrolysis of epoxy resin E12, undergone a dissolution-precipitation mechanism with the formation of fine-grain β-SiC.     

用于远程激光测距机的板条激光器

研制了用于远程激光脉冲测距机的板条激光器。使用半导体泵浦的MOPA激光结构实现了大于250 mJ的脉冲激光输出,输出脉冲宽度为12.83 ns,最终输出激光光束束散角为0.18 mrad。该激光测照器可应用于远程激光测距。对激光测距机的测距与照射能力进行了理论计算与分析。理论分析表明,应用于机载平台时,该激光测照器能够实现50 km距离的激光测距。该型激光测距机具有测距距离远,重量轻,结构紧凑等特点,具有广泛的应用前景。     

卫星激光通信粗跟踪系统复合控制策略

针对卫星激光通信粗跟踪系统的跟踪稳定精度指标要求高的特点,建立了基于永磁同步电机直接驱动的粗跟踪系统模型并进行了跟踪稳定误差分析。在采用传统PID控制策略存在跟踪误差较大、动态性能较差等不足的基础上,提出了一种基于粗跟踪系统的改进型前馈复合控制策略。从理论上分析了前馈复合控制策略提高了粗跟踪系统的动态性能,为降低跟踪稳定误差提供了改善方案。地面实验验证结果表明,与传统控制策略相比,改进型复合控制策略极大地降低了系统的动态跟踪误差,动态跟踪误差由606μrad降低至13μrad(1δ)。进一步的在轨实验也验证了改进型复合控制策略的合理性和先进性,总体指标满足了卫星激光通信终端的极高精度要求。本文所提出的控制策略对其他高性能跟踪伺服系统设计也具有较大的借鉴意义。     

掺铒单模光纤飞秒脉冲激光器和放大器

为了获得一种被动锁模掺铒光纤振荡器及功率放大器，数值模拟出超短脉冲在光纤中的传输和演化过程，并基于此搭建了一种被动锁模掺铒光纤飞秒振荡器及功率放大器。实验获得了中心波长1560 nm、重复频率100 MHz、输出功率30 mW、脉冲宽度85 fs超短脉冲。通过采用PPLN晶体进行倍频，进一步获得了输出功率5 mW，中心波长780 nm的飞秒脉冲。该光纤激光器为全保偏光纤结构，具有体积小巧、可靠性高、稳定性好的特点。     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.