Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

水泥窑余热发电系统用耐磨材料的研制与应用

本研究针对水泥窑余热发电系统的工作条件,根据耐磨材料的损毁机理,采用高铝矾土、煅烧氧化铝粉、黏土、硅微粉等为原料,以磷酸二氢铝为结合剂,以铝酸钙水泥为促硬剂,通过添加掩蔽剂和优化配料工艺,制备了水泥窑余热发电系统用耐磨材料,并对不同处理温度对耐磨材料的性能影响进行了分析。结果表明增强骨料与基质的结合能力有利于耐磨性的提高,磷酸及磷酸盐与氧化铝之间会随着温度的升高生成不同的磷酸铝相,都能够起到结合作用,比采用水泥结合更有利于提高材料在不同温度下的强度和耐磨性。使用结果表明,制备的耐磨材料施工性能优良,凝结硬化时间适当,强度高,抗冲刷性能好,在水泥窑余热发电系统中取得了良好的使用效果。     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Characteristics of tiger nut milk: effects of milling

A standard method for the extraction of tiger nut milk has been introduced. It has been shown that, although milling duration improves the yield of tiger nut milk solids and its nutrient composition, there is a quantifiable loss of nutrient in the pressing residue during milk extraction. Milling duration improved the colloidal stability of the milk against creaming during 16 h of storage. A higher milling intensity resulted in the aggregation of biological polymers which resulted in colloidal destabilisation. Milling improved the lightness and stability and reduced browning rate of the tiger nut milk during storage. This report is important for the production of tiger nut milk of consistent and comparable characteristics. Milling has been introduced as a processing method for the qualitative and quantitative modulation of the properties of tiger nut milk. It is recommended to develop further strategies to improve the colloidal stability of tiger nut milk as a beverage.     

基于WiMAX通信网络的电源监控系统的构建

分析了全球微波接入互存(WiMAX)的技术特点和算法复杂度,探讨了其在电源监控系统中的应用,提出了基于Inter WiMAX Connection 2250技术的远程电源监控系统。在讨论WiMAX物理层算法的基础上,确定了以正交频分多址(OFDMA)模式为主体的物理层通信协议,提高了信道的利用率,抑制了码间干扰,为构建电源监控系统打下了良好的基础。     

Iterative equalization combining algorithm in intersymbol interference channel

To realize joint optimization of spatial diversity and equalization combining in the intersymbol interference (ISI) channel, an iterative equalization combining algorithm is proposed. The proposed algorithm uses the coefficients of Turbo equalization to calculate the combination weights without estimating the signal to noise ratio in each diversity branch. The equalized symbols from different diversity branches are combined, and the extrinsic information output from the decoder is fed back to the equalizers, so as to exchange soft information between the equalizers and the decoder. The performance of the proposed algorithm is analyzed using the extrinsic information transfer (EXIT) chart and verified by simulations. Results show that our approach fully exploits time domain information from the multipath channel and spatial domain information from multi receiving antennas, which efficiently improve the performance of the receiver in the severe ISI channel.     

不同折流板结构螺旋折流板换热器传热性能的比较(英文)

Numerical simulations were performed on flow and heat transfer performances of heat exchangers having six helical baffles of different baffle shapes and assembly configurations, i.e., two trisection baffle schemes, two quadrant baffle schemes, and two continuous helical baffle schemes. The temperature contour or the pressure contour and velocity contour plots with superimposed velocity vectors on meridian, transverse and unfolded concentric hexagonal slices are presented to obtain a full angular view. For the six helix baffled heat exchangers, the different patterns of the single vortex secondary flow and the shortcut leakage flow were depicted as wel as the heat transfer properties were compared. The results show that the optimum scheme among the six configurations is a circumferential overlap trisection helix baffled heat exchanger with a baffle incline angle of 20° (20°TCO) scheme with an anti-shortcut baffle structure, which exhibits the second highest pressure dropΔpo, the highest overal heat transfer coefficient K, shel-side heat transfer coefficient ho and shel-side average comprehensive index ho/Δpo.     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.     

泛在电力物联网在北京经济技术开发区的应用探索

泛在电力物联网是物联网在电力领域的具体体现，建设泛在电力物联网是推进"三型两网"建设的关键环节，也是实现能源转型的必要手段。阐述了泛在电力物联网的定义，从供电公司角度出发，根据北京经济技术开发区实际情况，讨论了依托地区特点的泛在电力物联网实施策略和实际应用场景，分析了可能遇到的问题。得出结论：随着泛在电力物联网的深入建设，供电公司能够为电力客户提供多元化服务，提高客户满意度；地市供电公司能够依托泛在电力物联网开展更多电力相关业务；泛在电力物联网的安全性、实用性、有效性是发展面临的首要问题。