Experimental study on the propagation characteristics of hydrogen/methane/air premixed flames in a narrow channel

This work is focused on the explosion characteristics of premixed gas containing different volume fractions of hydrogen in a narrow channel (1000 mm × 50 mm × 10 mm) under the circumstance of stoichiometric ratio. The ignition positions were set in the closed end and the middle of the pipeline respectively. The results showed that when the gas was ignited at the pipeline closed end, the propagating flame was tulip structure for different premixed gas. When the hydrogen volume fraction was less than 40%, the flame propagation speed increased significantly with the rise of hydrogen volume fraction, and the overpressure peak also appeared obviously in advance. However, when the volume fraction of hydrogen was more than 40%, the increase of flame propagation speed and the overpressure peak occurrence time varied slightly. Furthermore, when the ignition position was placed in the middle of the pipeline, the flame propagation speed propagating to the opening end was much faster than that propagating to the closing end, and there was no tulip shape when the flame propagates to the opening end. The flame propagating to the closed end appeared tulip shape under the influence of airflow, and high-frequency flame oscillation occurred during the propagation. This work shows that the hydrogen volume fraction and ignition position significantly affected the flame structure, flame front speed, and explosion overpressure.     

Effect of wind condition on unintended hydrogen release in a hydrogen refueling station

Ambient condition, especially the wind condition, is an important factor to determine the behavior of hydrogen diffusion during hydrogen release. However, only few studies aim at the quantitative study of the hydrogen diffusion in a wind-exist condition. And very little researches aiming at the variable wind condition have been done. In this paper, the hydrogen diffusion in different wind condition which including the constant wind velocity and the variable wind velocity is investigated numerically. When considering the variable wind velocity, the UDF (user defined function) is compiled. Characteristics of the FGC (flammable gas cloud) and the HMF (hydrogen mass fraction) are analyzed in different wind condition and comparisons are made with the no-wind condition. Results indicate that the constant wind velocity and the variable wind velocity have totally different effect for the determination of hydrogen diffusion. Comparisons between the constant wind velocity and the variable wind velocity indicate that the variable wind velocity may cause a more dangerous situation since there has a larger FGC volume. More importantly, the wind condition has a non-negligible effect when considering the HMF along the radial direction. As the wind velocity increases, the distribution of the HMF along the radial direction is not Gaussian anymore when the distance between the release hole and the observation line exceeds to a critical value. This work can be a supplement of the research on the hydrogen release and diffusion and a valuable reference for the researchers.     

Influence of α′‐/α‐crystal polymorphism on properties of poly(l‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a biodegradable and biocompatible thermoplastic polyester produced from renewable sources, widely used for biomedical devices, in food packaging and in agriculture. It is a semicrystalline polymer, and as such its properties are strongly affected by the developed semicrystalline morphology. As a function of the crystallization temperature, PLLA can form different crystal modifications, namely α′‐crystals below about 120 °C and α‐crystals at higher temperatures. The α′ modification is therefore of special importance as it may be the preferred polymorph developing at processing‐relevant conditions. It is a metastable modification which typically transforms into the more stable α‐crystals on annealing at elevated temperature. The structure, kinetics of formation and thermodynamics of α′‐ and α‐crystals of PLLA are reviewed in this contribution, together with the effect of α′‐/α‐crystal polymorphism on the properties of PLLA. © 2018 Society of Chemical Industry     

2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

中低温煤焦油基炭微球的制备

通过馏分切割、温和加氢相结合对中低温煤焦油进行精制处理，精制后的原料采用分级热聚制备中间相炭微球。考察了精制处理条件对原料性质、中间相炭微球宏观外貌及微晶结构的影响。采用FTIR、GC-MS、族组成、元素分析对原料进行表征，采用SEM、XRD对中间相炭微球进行表征。结果表明：中低温煤焦油中300～430℃馏分油是制备中间相炭微球的较佳馏分。300～430℃馏分油中正庚烷可溶物（HS）质量分数高达84.76%，吡啶不溶物（PI）质量分数低至0.23%，杂原子含量低，芳烃化合物的环数为2～4环。300～430℃馏分油在T_H=350℃、p=8MPa、t=1.5h、剂油比1∶40（质量比）的条件下温和加氢得到的精制原料，经420℃热聚6h得制备的中间相炭微球宏观外貌、微晶结构较好。中低温煤焦油基炭微球的粒径范围为5～15μm，小球表面光滑，微观结构为地球仪型，经1450℃高温煅烧后，石墨化度达到12.33%。     

基于材料力学性能的最低设计金属温度曲线分析

铁素体钢在低温条件下存在明显的韧脆转变现象。为防止脆断事故的发生,需要确定铁素体钢制压力容器的最低使用温度。针对ASME中的A^D四条冲击豁免曲线,对应地选取了4种材料,基于材料实际的屈服强度和参考温度,按照ASME中豁免曲线的计算方法,计算得到4种材料的最低设计金属温度曲线,并与对应的A^D曲线对比,定量地分析ASME中豁免曲线的保守性。结果表明,ASME中的豁免曲线相对于材料自身的最低设计金属温度曲线保守性较大;韧性相近的材料被划分到不同的豁免曲线,使得韧性富裕量差异较大,对于某些材料,其断裂韧性被低估。     

基于压缩机-支架系统的异常噪声研究

针对某乘用车发动机转速在1 573 r/min，压缩机开启时车内噪声异常的问题，对样车进行试验分析与诊断，对压缩机-支架系统进行仿真分析，提出改进方案并验证改进效果。利用LMS声振信号采集系统采集振动噪声数据，采用频谱分析、阶次追踪等方法，并结合压缩机-支架系统模态仿真结果，确定车内异常噪声是压缩机轴频21阶与压缩机-支架系统3阶模态频率接近发生共振造成的。通过优化支架结构来提高压缩机-支架系统3阶模态频率以此来避免共振，并换装橡胶驱动盘缓和压缩机输入扭矩波动。将改进结构进行整车试验，结果表明：匀速工况空调开启时问题转速下，车内噪声降低了2.5 dB(A)；匀加速工况空调开启时发动机转速1 500~1 650 r/min区间，车内噪声无峰值，其余转速空调开启时改进前/后车内噪声基本不变，噪声波动趋势平缓。     

Supporting primary students' learning of fraction conceptual knowledge through digital games

With the advent of mobile technologies, well-designed fraction apps can be used to help children gain fraction knowledge, a challenging topic for both teachers and students. The present pilot study adopted a quasi-experimental design to investigate whether children can learn fraction concepts equally well if half of the lesson time (20 min) is replaced with game-based learning. Keeping the total lesson time (40 min) identical, the control group (N = 33) received traditional instruction, and the experimental group (N = 32) was presented with a blended learning approach spending half of the class time (20 min) playing tablet-based fraction games, where each of the learners had their own tablet. The results suggested that in the posttest, the experimental group achieved similar learning gains to the control group and appear to have achieved better performance in the transfer test than the control group. This paper also discusses the efficiency of game-based learning, the mechanism of how fraction games might enhance learning, and the potential of integrating game-based learning in educational settings.     

Impact of shape representation schemes used in discrete element modelling of particle packing

In different computer models, shape is represented using different methodologies, to varying degrees of precision. This paper examines two approaches to shape representation, and their effects on accuracy in the context of cylindrical particle packing. Two discrete element method (DEM) based software packages are used. A X-ray CT scan of a packed bed provides the experimental measurements for comparison. Eight sphere-composite representations of the same cylindrical pellet were tested. Two of these gave results that quantitatively follow experimental measurements. A range of factors that in theory could affect accuracy of the simulation results are examined, including edge roundedness, surface roughness and restitutional behaviour as a function of sphere-composite representations. The conclusion is that, for packing at least, matching the object's overall shape and dimensions is not enough. Only when a high enough resolution is applied to corners and edges, could the sphere-composite approach possibly match the experimental data quantitatively.     

马尔可夫跳变线性系统最优控制的研究现状与进展

马尔可夫跳变线性系统（MJLS）是一种具有多个模态的随机系统，系统在各个模态之间的跳变转移由一组马尔可夫链来决定。MJLS模型因其在表示过程中可以产生突变而更能精确的描述实际工程应用中的系统。近年来，MJLS的最优控制问题成为了研究的热点，动态规划、极大值原理以及线性矩阵不等式等成为了解决此类问题的主流方法。本文对MJLS最优控制领域的研究现状进行了综述。分别对一般情况下、带有噪声的情况下、带有时滞的情况下以及某些特定情况下的MLJS最优控制问题的国内外研究现状进行论述。最后进行了总结并提出MJLS最优控制领域未来值得关注的研究方向。