超声波流量计计量系统性能的主要影响因素

随着我国天然气工业的发展，已有大量超声波流量计用于高压、大流量的天然气计量。尽管我国已于2001年颁布并实施了气体超声波流量计使用方面的国家标准GB/T18604-2001，但是随着超声波流量计越来越广泛的使用，国内外对超声波流量计计量性能的影响因素已有了进一步的研究；而且，目前我国超声波流量计在天然气计量中的应用效果也还需要进一步改善。因此，根据目前国、内外最新研究成果，对噪声、脏污、压力及温度测量对超声波流量计计量系统性能的主要影响因素以及控制对策进行了分析探讨，以期改变虽经实验室检定合格、但用于现场却不能达到预期计量性能效果的情况，使超声波流量计在现场能够得到更好的应用。     

Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.     

如何控制液压系统的噪声

本文对液压系统噪声产生的原因进行了分析，并相应地介绍了控制液压系统噪声的几项具体措施，指出了在实施噪声控制过程中应注意的事项。     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

应用SPC技术对机械零件加工过程的管理和控制

介绍了SPC(统计过程控制)技术原理，以某传动轴外径φ45 0.50^0.90 mm为控制对象，提出应用SPC技术，对机械零件加工过程进行管理和控制，从而达到过程失控预警、过程不断改进、过程能力不断提高的目的，继而保证产品质量的稳定和不断提高。     

行波管放大器相位噪声的分析及其抑制

主要分析规则调相信号对行波管放大器频谱纯度的影响,并且根据行波管放大器相位噪声产生的过程和原因,提出两种抑制相位噪声的方法.     

空调器中多翼离心风机的噪声研究及结构优化

采用逐步回归法对大量的多翼离心风机实验数据进行拟合,针对家用空调行业中以噪声为其最重要 的考核标准,得出了噪声与叶轮结构参数及风机性能参数间的近似关系式,并以噪声为目标函数进行了优化计算。     

320×240 Pixels CMOS Digital Image Sensor with Wide Dynamic Range

A 320×240 CMOS image sensor is demonstrated,which is implemented by a standard 0.6 μm 2P2M CMOS process.For reducing the chip area,each 2×2-pixel block shares a sample/hold circuit,analog-to-digital converter and 1-b memory.The 2×2 pixel pitch has an area of 40 μm×40 μm and the fill factor is about 16%.While operating at a low frame rate,the sensor dissipates a very low power by power-management circuit making pixel-level comparators in an idle state.A digital correlated double sampling,which eliminates fixed pattern noise,improves SNR of the sensor, and multiple sampling operations make the sensor have a wide dynamic range.     

接收机整机最小噪声系数的实现

前级LNA的性能指标的好坏对接收机整体性能起主要作用。较流行的设计方法是用ADS等仿真软件在Smith圆图上作出LNA的等增益圆和等噪声圆，以确定LNA是否同时满足所要求的增益和噪声系数指标。这种方法虽然满足了设计要求，但往往不能获得整机噪声的最佳点。本文在符合设计指标后进一步对噪声和增益的关系进行分析，建立适用于常用接收机的简单模型，在此基础上获得基于整机噪声的最佳点。这种设计方法可以广泛应用于各种微波接收系统中,降低整机哭声系数.     

KMLS型立式砂泵的振动噪声产生原因及解决措施

针对KMLS型立式砂泵振动、噪声产生原因及其表现特征,提出了解决措施。通过对这些原因的分析研究,可以提供泵设计者和生产者在减少砂泵振动方面采取相应的措施,使KMLS型立式砂泵能更好的服务于用户。