最新水冷式全固态数字调幅600kW中波发射机

数字调幅制式是当前国际上较先进的调制技术，ＤＸ系列全固态数字调幅中波发射机的电声指标和工业效率都是很先进的，过去的ＤＸ大功率机采用风冷方式，本文介绍了最新水冷ＤＸ－６００发射机的设备情况和技术特点。     

A fuzzy diagnosis approach using dynamic fault trees

By incorporating digraph models, fault trees and fuzzy inference mechanisms in a unified framework, a novel approach for fault diagnosis is developed in this work. To relieve the on-line computation load, the fault origins considered in diagnosis are limited to the basic events in the cut sets of a given fault tree. The symptom occurrence order associated with each root cause is derived from system digraph with the qualitative simulation techniques. The implied candidate patterns are enumerated according to two proposed theorems and then encoded in the inference system with IF-THEN rules. The simulation results show that the proposed approach is not only feasible but also capable of identifying the most likely cause(s) of a hazardous event at the earliest possible time.     

Selective partial oxidation of light paraffins with hydrogen peroxide on thin-layer supported Nafion-H catalysts

Thin-layer carbon supported Nafion-H catalysts were found to be active and highly selective (S>98%) for the partial oxidation of C₁-C₃ alkanes, in a three phase catalytic membrane reactor (3PCMR), under mild conditions and in the presence of H₂O₂. The influences of the catalyst teflon loading and H₂O₂ concentration on the reaction rate have been evaluated. A reaction pathway, based on the electrophilic hydroxylation of the C-H bond of alkanes with protonated hydrogen peroxide (H₃O ₂ ⁺ ), is discussed.     

Estimation of Thermodynamic Properties from Binary Phase Diagram

The general relationship between binary phase diagrams and the thermodynamic properties was system-atically derived without any assumption.A procedure was presented to estimate the thermodynamic proper-ties from the binary phase diagrams.     

多模光纤出射的光通过透镜后的场分布

用部分相干光理论,研究了单模激光入射的多模光纤出射的光经透镜后,在菲涅尔衍射区内场的分布。     

Mg-Li-Al合金近液相线制浆及部分重熔

采用近液相线铸造方法制备了Mg—5％Li—3％A1合金的半固态浆料。通过对该合金近液相线铸造与常规铸造组织进行比较，以及在不同静置时间、不同冷却速率下对其铸造组织的影响，较详细地分析了近液相线铸造组织的变化过程。试验结果表明，在Mg—Li合金熔炼中，添加2％Ca可实现阻燃，但效果不如对一般镁合金；与常规铸造相比，近液相线铸造可获得均匀、细小枝晶的组织结构；适当静置或提高冷却速率有利于组织的细化和均匀化；在适当的部分重熔工艺条件下，坯料组织可获得较理想的触变组织。     

Forced convection subcooled boiling of binary mixtures

A mode based on an additive mechanism of heat transfer is proposed for forced convection subcooled boiling of binary mixtures. The contributing modes of heat transfer are: (i) the heat transferred as latent heat by the rising bubbles, (ii) the heat transferred as the heat contained in the superheated thermal layer that is removed from the surface in the wake of the rising bubbles and (iii) the single phase forced convection heat transfer from the heating surface not influenced by the bubbles. Experimental data from the literature on binary systems show good agreement with the model, validating the postulated mechanism.     

Diffusion Coefficient of a Binary Liquid System

A generalized diffusion coefficient correlation for a binary system of liquids has been developed to represent the data for a wide range of temperatures. Detailed analysis shows that the proposed correlation fits the experimental measurements of diffusivity with the corresponding calculated values with an acceptable percentage error.     

铸件浸渗系统脱液机故障树的建立和分析

利用FTA方法对脱液机的各种故障进行系统分析,建立了脱液机的故障树,并对故障树进行定性分析.找出了影响脱液机可靠性的主要因素,提出了提高脱液机可靠性的相应措施.     

充分灌与调亏灌溉条件下桃树滴灌的耗水量研究

本文研究了充分灌与调亏灌溉条件下桃树滴灌的耗水量。在田间设置有两个处理，其一是在整个生育期以蒸发量的80%进行充分灌溉；其二是在果实生长缓慢期以蒸发量的20%进行亏缺灌溉，而在其它季节以蒸发量的80%进行充分灌溉。利用石膏块土壤水分传感器和中子仪分别测量了根区土壤水势和土壤含水量的变化，并实测了果实生长量、枝条生长量和产量。利用水量平衡法得出了在上述两种滴灌条件下桃树不同生育期的日均耗水量与蒸发皿系数。与充分灌比较，调亏灌溉对产量没有影响，灌水量减少了32%，并有效抑制了枝条生长。