The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

An Investigation of Milk Powders Produced by a Laboratory-Scale Spray Dryer

A mini spray dryer has been used to investigate morphological changes that occur to milk particles during the spray drying process. We have found that the mini spray dryer is ideal for such investigations, because phenomena such as skin and vacuole formation in particles can be analyzed without the added complication of particle agglomeration, which only occurs in much larger spray dryers where particle number concentrations are higher. We have confirmed observations made by various researchers that the bulk density of spray-dried milk powder is greatly affected by the drying temperature, due to the strong influence of the latter on the porosity of the particles. In addition, we have attempted to explain observations made by various workers that fat accumulates preferentially at the surface of a particle during drying by postulating that fluid fat is transported towards the surface, via a network of cracks and pores, by the development of a vacuole overpressure which is also responsible for the inflation of the particle. Finally, we have shown that milk powders can be spray dried a second time, by reconstitution with water, with no change to the thermodynamic characteristics of the resultant powder. Thus, milk concentrates for spray drying research can be prepared from already-spray-dried milk powders rather than using the more arduous evaporation method to concentrate unprocessed milk.     

硫铁矿沸腾炉内蒸发管组防磨技术的探讨

为减少磨损,沸腾炉内蒸发管采用加焊半圆形钢板防磨.探讨了沸腾炉内蒸发管加焊半圆形钢板的防磨机理.实际使用情况表明,加焊半圆形钢板防磨大大降低了维修费用,显著提高了防磨效果.     

The appropriateness of the systematic framework to develop diagnosis procedures of nuclear power plants—an experimental verification

It has been well recognized that a diagnosis procedure that allows operators to successfully identify the nature of an on-going event is inevitable for an effective and appropriate recovery. Unfortunately, studies for a framework that can suggest a unified and consistent process in constructing a serviceable diagnosis procedure seem to be scant. Thus, Park et al. have suggested a systematic framework that can be used to construct a useful diagnosis procedure. In addition, the diagnosis procedure that is currently in use at the reference nuclear power plant (NPP) is reformed in order to demonstrate the appropriateness of the suggested framework. However, the necessity of a well-designed experiment is proposed to confirm the appropriateness of the suggested framework.In this regard, in this study, an experiment is conducted using a full-scope simulator of the reference NPP. From the experiment, two sets of operators' diagnosis performance data are collected, and then they are compared to investigate the change of an operator's diagnosis performance with respect to two types of diagnosis procedures.As a result, it is shown that an operator's diagnosis performance is improved when the revised diagnosis procedure is used. Therefore, it is reasonable to conclude that the suggested framework is useful in constructing an effective diagnosis procedure.     

Mechanical and microstructure studies on the modification of CA film by blending with PS

DriedMusa paradiciaca (banana) stem and veins of the leaves, which were hitherto discarded as a waste, were collected and used as starting material for the preparation of cellulose and cellulose acetate. This cellulose acetate was mixed with polystyrene to form blend of cellulose acetate-polystyrene in order to provide enhanced stability and extended utility to the end products. The films of these composites or their individual partners were made separately and studied for their mechanical properties, chemical modification and morphological changes. We report here that banana stem is good source of cellulose and that cellulose completely undergoes modification upon esterification.     

Optimal size,hydraulic retention time and volatile solids loading rate of biogas unit using water hyacinth

With a view to evaluate the effects of hydraulic retention time and volatile solids loading rate on methane production using water hyacinth, experiments were conducted in a 160 dm³ capacity, well-mixed continuous digestion unit at ambient temperature. The optimal design of biogas plant using water hyacinth was elucidated, to provide a unit giving a maximum methane yield of 0.16 nm³ kg^?1 volatile solids added, which was 60% greater than the conventional plant using cowdung. The calculations of optimal design factors were based on reactor size, hydraulic retention time and volatile solids loading rate; considerations were made of capital cost, running costs and operational revenue.     

H9000 V4.0计算机监控系统技术特点概要

为了满足三峡右岸电站的应用需要,在H9000 V3.0计算机监控系统的基础上研制开发了H9000 V4.0系统,改进和完善了原系统已有功能,开发了新功能,进一步提高了系统的性能指标和可靠性指标。文中主要介绍H9000 V4.0系统的设计原则,以及数据采集、人机联系、报表定制、Web信息发布、历史数据管理等主要新功能。     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

进口VPSA制氧装置的流程特点及配置

详细介绍了进口的VPSA制氧装置的流程特点、工艺参数及主要设备的配置。实际运转证明 ,该制氧装置具有运行可靠、启动时间短、部分负荷性能优越、负荷转换速度快等优点 ,能满足金隆铜业有限公司的实际生产要求。     

40000m~3/h空分设备主换热器的设计及制造

通过对进口 4 0 0 0 0m3 /h空分设备主换热器进行结构分析及对比模拟计算 ,用国产传热翅片进行设计、采用真空钎焊工艺制造的主换热器 ,经并网运行 ,设计指标优于原空分设备 ,为今后成套大型空分设备板翅式换热器国产化设计、制造创造了条件。