IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

热镀锌工艺对Ti-IF钢光整热镀锌板组织和性能的影响

在连续热镀锌线上研究了RTH带钢温度和光整延伸率对Ti—IF钢光整热镀锌板组织和性能的影响。试验表明，当RTH带钢温度在830℃以下时，成品铁素体晶粒度为10．0级，织构类型以{332}、{114}为主，随着带钢温度的进一步提高，热镀锌板的晶粒逐渐粗化，织构成为典型的{111}织构，且取向密度增加，r值随之提高，但当带钢温度在900℃以上时，织构又趋于无规则分布，r值显著降低；光整延伸率对Ti—IF钢光整热镀锌板力学性能的影响很大，随着光整延伸率的提高，屈服强度明显提高，n值明显降低，延伸率降低，抗拉强度变化较小，且光整延伸率对性能的影响与成品铁素体晶粒尺寸有关，成品晶粒越粗，光整延伸率的影响越大。因此对于Ti—IF钢光整热镀锌板而言，n、r值是一对矛盾体，在制订热镀锌工艺时，需根据使用条件的不同，对其n、r值进行综合考虑。     

Constitutive modelling and numerical simulation of multivariant phase transformation in superelastic shape‐memory alloys

This work concerns the micromechanical constitutive modelling, algorithmic implementation and numerical simulation of polycrystalline superelastic alloys under multiaxial loading. The model is formulated in finite deformations and incorporates the effect of texture. The numerical implementation is based on the constrained minimization of the Helmholtz free energy with dissipation. Simulations are conducted for thin tubes of Nitinol under tension–torsion, as well as for a simplified model of a biomedical stent. Copyright © 2004 John Wiley & Sons, Ltd.     

Instron texture profile of buffalo milk cheddar cheese as influenced by composition and ripening changes

Buffalo milk Cheddar cheese samples of different ages were analysed for compositional attributes (CA), ripening indices (RI) and Instron Textural Profile (ITP). All samples were compositionally alike, except for pH and salt-in-moisture (SM) contents. RI showed significant variations. CA and RI showed highly significant correlations within themselves and with each other, except for moisture with pH, SM with moisture, MNFS, Fat and FDM and Fat with MNFS. The ITPs of cheeses showed significant variations and had highly significant intercorrelations indicating their interdependence. CA (except moisture and MNFS) and RI showed a highly significant correlationship with ITPs. Moisture content showed a highly significant correlationship with all ITPs, except cohesiveness and springiness, where it was significant. MNFS content showed significant correlations only with hardness and brittleness. Stepwise regression analysis revealed that MI was the most predominant factor influencing cheese texture, followed by pH, SM, FDM and TVFA. Knowing Ca and RI, the textural properties of cheeses can be forecast through mathematical equations. Similarly the age of cheese can also be predicted if RI and/or textural properties are known.     

Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

定量确定纤维织构轴密度分布的矢量法

本文将大幅度减少衍射极图测试数目的织构分析矢量法应用于定量确定纤维织构材料的晶粒取向分布;采用蒙特卡罗方法计算系数矩阵σ_(pn)(hkl)。对立方晶系的研究结果表明,由一张极图甚至一张不完整极图即可准确地构建纤维轴密度分布图。     

织构对铟凸点剪切强度的影响

制作了2种形式的铟凸点：即直接蒸发沉积的铟柱和将铟柱回流得到的铟球。同时对比了铟柱和铟球2种凸点的剪切强度，测试结果表明铟球剪切强度为5.6MPa，铟柱的剪切强度为1.9MPa，前者约为后者的2.9倍。对铟凸点微观结构的X光衍射分析发现：铟柱剪切强度低是织构弱化所致；铟球剪切强度高是由于回流破坏了铟柱的理想（101）丝织构模式，从而提高了铟球的剪切强度。     

平湖油气田古近系花港组低阻油层成因与识别分析

低阻油气层是一种非常规储层 ,其油气层电阻率与邻近水层电阻率接近 ,或有时低于水层的电阻率。通过对花港组H5砂层组的岩石类型、颗粒大小、粘土矿物的成分及其分布、孔隙结构、润湿性、地层水矿化度进行研究 ,表明该砂层组低阻的原因主要是由于高束缚水饱和度及高地层水矿化度引起的。