芽孢杆菌Bacillus sp.dwc-2对模拟地下水中U(Ⅵ)的还原行为研究

在厌氧条件下研究了西南地区一种典型土壤微生物芽孢杆菌Bacillus sp.dwc-2对模拟地下水中U(Ⅵ)的还原行为，重点考察了时间、无机阴离子、腐殖酸（HA）及富里酸（FA）对还原的影响，并利用TEM、EDS、SAED和XPS对还原后的样品进行了表征。结果表明：在pH=7.0、c_NaHCO3=5 mmol/L和T=303 K条件下，Bacillus sp.dwc-2对U(Ⅵ)的还原率随时间的增加而增加，24 h内最大还原率为12.2%，此后则随时间的增加逐渐降低；HA和FA对U(Ⅵ)的微生物还原行为有一定影响，其中HA和FA浓度为25 mg/L时，U(Ⅵ)的还原在24 h最明显，其还原率分别为14.2%和16.2%，但随着HA和FA浓度的继续增加，因在U(Ⅵ)离子与HA、FA形成的配合物表面形成致密的腐殖层，抑制了电子的转移，阻止了U(Ⅵ)的还原。此外，研究表明HCO₃^-也会抑制U(Ⅵ)的还原。TEM-SAED和XPS分析证实了还原过程中U(Ⅳ)的存在。上述结果可为真实环境中微生物还原U(Ⅵ)提供基础数据和参考。     

Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

Stochastic free vibration analyses of composite shallow doubly curved shells – A Kriging model approach

This paper presents the Kriging model approach for stochastic free vibration analysis of composite shallow doubly curved shells. The finite element formulation is carried out considering rotary inertia and transverse shear deformation based on Mindlin’s theory. The stochastic natural frequencies are expressed in terms of Kriging surrogate models. The influence of random variation of different input parameters on the output natural frequencies is addressed. The sampling size and computational cost is reduced by employing the present method compared to direct Monte Carlo simulation. The convergence studies and error analysis are carried out to ensure the accuracy of present approach. The stochastic mode shapes and frequency response function are also depicted for a typical laminate configuration. Statistical analysis is presented to illustrate the results using Kriging model and its performance.     

云杉八齿小蠹Ips typographus L.虚拟模型构建方法研究

本文以云杉八齿小蠹Ips typographus Linnaeus为例,经标本选取,观察虫体整体形态,绘制整体结构草图,电子显微镜观察局部、得到局部数字图像,分别建立虫体每一部分的高精度细节。把模型每部分拼装在一起组成整体模型,构建出了云杉八齿小蠹三维虚拟昆虫数字化模型。     

A model- and simulation-based approach for tolerancing and verifying the functional capability of micro/nano-structured workpieces

The evaluation of functional features of manufactured workpieces is based on GO- and NO-GO-test results, which are obtained by comparing measured geometric characteristics with nominal dimensions and tolerances specified by the designer. These geometrical specifications are based on a tolerancing system, which was originally defined for the function mating capability. Against the background of upcoming lots of other new functions (like reduction of flow resistance, light absorption, reduction of friction, diffraction of light, self-cleaning or mass transmission) are to be realized with our products – particularly by micro- and nano scaled features. If the verification process will deliver the prediction of the achievable degree of functionality, the usability of a part can be assessed more accurately and in consequence quality and economics can be improved. So, a new principle for tolerancing and verifying turns out to be necessary. In this paper the fundamental deficit of the actual tolerancing and specification systems GPS and ASME Y14.5 is derived and the path for enlarging the system by preposing a functional model is shown. To verify the functional capability of the workpieces an approach based on simulations done with the parameterized mathematical–physical model of the function is suggested. Advantages of this approach will be discussed and demonstrated by examples with microstructured inking rolls, crankshafts and injection valves.     

Piezoresistive in-situ strain sensing of composite laminate structures

Various methods have been developed to monitor the health and strain state of carbon fiber reinforced polymers, each with a unique set of pros and cons. This research assesses the use of piezoresistive sensors for in situ strain measurement of carbon fiber and other composite structures in multidirectional laminates. The piezoresistive sensor material and the embedded circuitry are both evaluated. For the piezoresistive sensor, a conductive nickel nanocomposite sensor is compared with the piezoresistivity of the carbon fiber itself. For the circuit, the use of carbon fibers already present in the structure is compared with the use of nickel coated carbon fiber. Successful localized strain sensing is demonstrated for several sensor and circuitry configurations. Numerous engineering applications are possible in the ever-growing field of carbon-composites.     

Microwave assisted-in situ synthesis of porous titanium/calcium phosphate composites and their in vitro apatite-forming capability

Microwave irradiation has been proven to be an effective heating source in synthetic chemistry, and can accelerate the reaction rate, provide more uniform heating and help in developing better synthetic routes for the fabrication of bone-grafting implant materials. In this study, a new technique, which comprises microwave heating and powder metallurgy for in situ synthesis of Ti/CaP composites by using Ti powders, calcium carbonate (CaCO₃) powders and dicalcium phosphate dihydrate (CaHPO₄·2H₂O) powders, has been developed. Three different compositions of Ti:CaCO₃:CaHPO₄·2H₂O powdered mixture were employed to investigate the effect of the starting atomic ratio of the CaCO₃ to CaHPO₄·2H₂O on the phase, microstructural formation and compressive properties of the microwave synthesized composites. When the starting atomic ratio reaches 1.67, composites containing mainly alpha-titanium (α-Ti), hydroxyapatite (HA), beta-tricalcium phosphate (β-TCP) and calcium titanate (CaTiO₃) with porosity of 26%, pore size up to 152 μm, compressive strength of 212 MPa and compressive modulus of 12 GPa were formed. The in vitro apatite-forming capability of the composite was evaluated by immersing the composite into a simulated body fluid (SBF) for up to 14 days. The results showed that biodissolution occurred, followed by apatite precipitation after immersion in the SBF, suggesting that the composites are suitable for bone implant applications as apatite is an essential intermediate layer for bone cells attachment. The quantity and size of the apatite globules increased over the immersion time. After 14 days of immersion, the composite surface was fully covered by an apatite layer with a Ca/P atomic ratio approximately of 1.68, which is similar to the bone-like apatite appearing in human hard tissue. The results suggested that the microwave assisted-in situ synthesis technique can be used as an alternative to traditional powder metallurgy for the fabrication of Ti/CaP biocomposites.     

A novel fast distance relay for series compensated transmission lines

This paper presents a fast distance relay for series compensated transmission lines based on the R–L differential-equation algorithm using the theory of equal transfer process of transmission lines. The measuring distances based on the proposed algorithm can fast approach the actual value of fault distance when a fault occurs in front of the series capacitor. When a fault occurs behind of the series capacitor, the fault loop, including the series capacitor, does not match the R–L transmission line model, so the measuring distances fluctuate severely. Based on this, the relative position of the fault with respect to the series capacitor can be judged effectively according to the fluctuation range of the measuring distances, and the accurate fault location can be obtained fast. A variety of PSCAD/EMTDC simulation tests show that the new relay has fast operating speed and high accuracy when applied to the long series compensated transmission lines.     

以有机化学课程内容为引导，加强课程思政的探索与实践

有机化学是化学化工、材料、制药、食品等多个专业的基础课程,在其教学过程中,教师可以根据课程的内容及特点,分别以有机化学发展中的重大历史事件、有机化物的性质及有机反应为引导,开展学生的思想品德教育,加强课程思政建设。