碎软煤层条带瓦斯地面高效抽采技术研究

为了提高碎软煤层条带瓦斯抽采效率和效果,基于目前地面瓦斯抽采主要采用垂直井或从式井的方式抽采效果差、效率低的现状,通过理论和实验分析论证了穿岩层压裂改造煤储层的可行性,提出了在目标煤层顶板岩层中钻水平井,并通过垂直向下射孔以及采用泵送桥塞分段进行压裂的方式进行地面瓦斯抽采。试验结果表明:顶板分段压裂水平井单井产量高、高稳产期更长、产量衰减更慢;有效水平井段控制区域内瓦斯下降均匀,更有利于进行条带瓦斯抽采;相同投资条件下,采用水平井的方式瓦斯抽采效率和投入产出比更高。     

Influence of the ZrB2 content on the anti-oxidation ability of ZrB2-SiC coatings in aerobic environments with broad temperature range

ZrB₂-SiC coatings with different ZrB₂ contents were prepared by liquid phase sintering. The oxidation processes of coatings were explained according to TG results of ZrB₂-SiC coatings and powders tested from 298 K to 1773 K. Results show that, increasing ZrB₂ content made the weight of the samples changed from weight-loss of 10.04% to weight-gain of 0.14%, while the fastest weight-loss regions were narrowed, whose inflection points reduced from 1310℃ to 1050℃. Increasing ZrB₂ content made the relative oxygen permeability of the ZrB₂-SiC/SiC coatings reduced from 40%–60% to -10%-5%. Increasing ZrB₂ content enhanced high-temperature stability of coatings, making final weight of samples changed from weight-loss of 0.16% to weight-gain of 0.11% after oxidation at 1773 K for 200 h. The peeling and dispersion of Zr-oxides formed Zr-B-Si-O compound glass layer, presenting enhanced stability, dispersion strengthening and pinning effect of Zr-oxides, which were responsible for the excellent anti-oxidation protective effect of coatings in a broad temperature region.     

覆岩结构类型与开采覆岩损害特征分析

煤层开采打破了上覆岩层原有的平衡,必然引起岩层的移动、破断,导致应力场和裂隙场的改变,工作面出现矿压显现。上覆岩层的岩性和组合结构对工作面开采覆岩损害特征分布影响显著,一般岩性越坚硬,上覆岩层应力集中程度越高,采动裂隙越发育,矿压显现也越明显;坚硬岩层尤其是关键层对覆岩的破断运动起控制作用,覆岩破断发展到一定层位后软弱岩层往往是抑制覆岩破断进一步向上发展的关键。当工作面上覆岩层同时存在远近场关键层时,近场关键层的周期性破断引起裂隙带范围内岩层的运动和工作面周期来压;而远场关键层的周期性破断导致地表裂缝或台阶下沉,工作面压力急剧上升,有时甚至导致煤矿动压灾害,尤其是远近场关键层同步破断时动力现象更明显。通过地面钻孔使远场关键层提前破断是防止此类动力灾害的关键。     

脱硫活性焦水洗再生过程实验研究

对5种活性焦水洗再生前后的脱硫性能进行实验研究，通过比表面积（BET）、X射线光电子能谱（XPS）方法表征水洗再生工艺对活性焦孔隙结构和表面化学性质的影响，揭示影响活性焦水洗再生性能的关键因素。结果表明:活性焦脱硫硫容的大小和水洗再生率的高低没有直接关系；微孔比表面积较大的活性焦脱硫性能较好，中大孔孔容较大的活性焦水洗再生率较高，同时具备较大的微孔比表面积和中大孔孔容结构的活性焦适宜水洗再生工艺；活性焦表面极性含氧官能团含量越高水洗再生效果越好；活性焦AC5经过6次水洗再生循环，微孔中的硫酸经过多次累积后可以被水洗出，稳定再生率保持在45%~50%，最适用于活性焦水洗再生工艺。     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

贺兰山西麓中生代构造反转及意义

通过对小松山断裂特征的再分析和对顺层断层特征的观察研究发现,发育于贺兰山北段西麓的小松山“推覆”构造实际上是一个滑覆构造。该区于晚侏罗世之后发生大规模构造反转,贺兰山沉积特征及玄武岩环境指示该区是一大陆裂谷斜坡,在中生代早中期并不存在大规模的东西向挤压应力环境。滑覆面之下的三叠系—中上侏罗统的褶皱变形及顺层剪切是这种滑覆引起的局部构造变形,与鄂尔多斯地块西部发育的典型的东西向逆冲形成明显对比,值得重视。      

国外MCM及其主要制造技术的发展现状

MCM具有胜过PCB、LSI和一般HIC的诸多优点,正在逢勃发展,可望成为九十年代的代表性技术。本文从市场和技术两个方面评述MCM的发展潜力,重点介绍近年来国外MCM主要制造技术的现状及发展态势,试图引起人们对它的关注。     

复合乳化沥青的粘附性试验方法研究

鉴于目前使用的阳离子乳化沥青粘附性试验方法难以有效评价复合乳化沥青粘附性，通过试验研究并综合考虑乳化沥青施工和路用实际情况，提出了乳化沥青水煮法试验方法和采用该方法检验复合乳化沥青粘附性时的评定标准。     

An updated correlation for crack-arrest fracture toughness for nuclear reactor pressure vessel steels

An updated and statistically-rigorous correlation is provided for crack-arrest toughness values versus normalized temperature for light-water nuclear reactor pressure vessel (RPV) steels. The database used in this effort is larger than applied heretofore and includes results from tests of laboratory-size specimens and from tests of large-scale specimens, which contain features prototypical of operating RPVs. The mathematical methodology used is based on a lognormal distribution, with its parameters calculated by orthogonal distance regression. This correlation was developed as one of several items updated for use in the US Nuclear Regulatory Commission's extensive program to evaluate and potentially revise its rule for ensuring structural integrity of operating RPVs when subjected to pressurized thermal-shock transients.     

玻璃两面重叠手印拍摄机理

根据斯涅尔定律和菲涅尔公式阐述清水衬底法消除玻璃下界面手印或玻纹的影像，以及用偏振光，紫外线拍摄玻面痕迹的方法和机理。