Ag/CeO2-ZnO催化剂上甲醇部分氧化制氢气研究

研究了用于甲醇部分氧化制氢气反应的Ag/CeO2-ZnO催化剂的制备条件以及反应条件对催化剂性能的影响.Ag/CeO2-ZnO催化剂中银含量、焙烧温度、反应温度以及反应气的比例等对催化剂性能具有很大的影响.Ag/CeO2-ZnO催化剂的制备条件以及反应条件控制在一定范围内时,Ag/CeO2-ZnO催化剂对甲醇部分氧化制氢气具有很高的催化活性与选择性.     

(Ag)_核·(Au)_壳复合纳米粒子的制备

以银原子团簇作晶种,采用微波高压液相合成法制备了分散性好、规则球形的(Ag)核·(Au)壳复合纳米粒子。研究了(Ag)核·(Au)壳复合纳米粒子的紫外可见吸收光谱和共振散射光谱特性。结果表明,液相(Ag)核·(Au)壳复合纳米粒子和高压微波合成的液相金纳米粒子的最强共振散射峰均在580nm处,它们的吸收光谱图相似,最大吸收分别在518.5nm和524.8nm。     

Synthesis of the Silver Nanofluid by ASNSS Process

Arc Spray Nanoparticle Synthesis System (ASNSS) has been used to prepare the silver nanofluids in this study. The metal electrodes under the electrical discharge will melt and evaporate rapidly and condense to form the nanoparticles in the dielectric fluid at lower temperature and produce the suspended nanoparticle fluid. Thus, the mechanism of the ASNSS process is superheating the electrodes by plasma to form metallic nuclei and supercooling these nuclei by dielectric liquid to produce nanofluid. This study considers the different controlling parameters such as discharge current,discharge voltage, pulse-duration time, electrode diameter, and the temperature of dielectric liquid. The optimally operated parameters can be obtained to produce the finer particle size in nanofluid. The results indicate the silver electrodes in alcohol fluid will produce the spherical nanosilver particles. The mean particle size of silver in different dielectric liquid temperatures of-40, -20, 0, and 10℃ is about13.4, 15.8, 17.5, and 21.6 nm, respectively. This indicates that the well suspended fluid can be obtained by controlling the lower dielectric fluid temperature.     

银掺杂对二氧化钛晶型转变的影响

采用溶胶-凝胶法制备了银掺杂的TiO2粉末,用XRD分析了掺银TiO2胶体经不同温度热处理后的晶型转变。结果表明:与未掺银的TiO2粉末相比,掺银TiO2从锐钛矿相向金红石相转变的起始温度较高,而且锐钛矿-金红石相变的温区范围变窄,晶型转变过程较快。     

沉积Ag的TiO_2纳米管的制备及其光催化性能的研究

采用电化学阳极氧化法制备了管长约为1.48μm,管径约为87 nm的Ti O2纳米管,然后采用光还原沉积法在不同浓度的AgNO3溶液中制备了沉积单质Ag的Ti O2纳米管.利用SEM,XRD和XPS对Ag-Ti O2纳米管进行了表征,并以罗丹明B溶液为目标降解物评价了其光催化活性.结果表明:Ag微粒是以稳定的单质形式存在,Ag-Ti O2纳米管的光催化活性随着AgNO3溶液浓度的增大而呈增大的趋势,当AgNO3浓度达到0.08 mol/L时其活性达到最大值,而后随着浓度的增大活性反而下降.     

Influence of surface finish and annealing treatment on oxidation behavior of Ti-48Al-8Cr-2Ag alloy

The effect of surface finish and annealing treatment on the oxidation behavior of Ti-48Al-8Cr-2Ag (molar fraction, %) alloy was investigated at 900 and 1 000 °C, respectively in air. Thermal gravimetric analysis (TGA) was conducted for the characterization of oxidation kinetics. The microstructures of oxide scales were studied by scanning electron microscopy (SEM) and transmission election microscopy (TEM) techniques. Unfavorable effect of the annealing treatment on the oxidation behavior of the coating was also investigated. The results indicate that the oxidation behavior of the alloy is influenced by surface finish and annealing treatment. The oxidation rate of ground sample is lower than that of the polished alloy at 1 000 °C in air. The former forms a scale of merely Al₂O₃, and the latter forms a scale of the mixture of Al₂O₃ and TiO₂. Annealing can improve the formation of TiO₂. Foundation item: Project(2007430028) supported by the Science and Technique Foundation of Henan Educational Committee, China     

Evaluation on wear behavior of Cr-Ag-N and Cr-W-N PVD nanocomposite coatings using two different types of tribometer

Practice has proven that CrN performs better than TiN under some specific tribological applications. Nevertheless, the relatively soft nature of CrN still remains a problem. This paper reports experimental results on increases in hardness of sputtered PVD CrN coatings by means of additions of varying content of Ag or W. The resulting Cr-Ag-N and Cr-W-N coatings, grown on JIS SKH51 steel substrates, were characterized using SEM, EDS, WDS, XRD, micro-indentation hardness testing and scratch adhesion tests. Moreover, wear behavior was studied on two types of tribometer, employing different contact regimes — a ‘cylinder-on-disk’ line-contact reciprocating-sliding regime and a ‘ball-on-disk’ point-contact rotating-sliding regime.The experimental results can be summarized as follows: The hardness of Cr-W-N coatings increased with increasing W content; reversely, that of Cr-Ag-N coatings decreased with increasing Ag content. The additions of Ag and W resulted in a formation of secondary phases, elemental Ag and WN, respectively, uniformly embedded in the CrN coatings. With the two different types of tribometer, the observed trends for wear behavior, wear and friction coefficient, were nearly identical, indicating that both Ag and W additions to CrN coatings were beneficial. However, the Cr-W-N coatings were significantly more wear resistant than the Cr-Ag-N coatings. With the addition of W at 6.8 at.%, the largest wear improvement of 73%-85% was achieved.     

ZnO／Ag纳米复合材料光催化性能研究

通过XRD、TEM测试研究了自制ZnO／Ag纳米复合材料的结构和形貌，通过UV检测确定了以该纳米复合材料为光催化剂，在不同条件下对甲基橙的光催化降解率。结果表明：与空气煅烧相比，真空煅烧所得纳米复合材料的光催化降解效果更好，且光催化降解率随纳米复合材料用量增加而增大：甲基橙溶液的pH在5左右时，光催化降解率最高：H2O2浓度为0．9g／L时，光催化降解率可达100％。     

Effects of Ag addition on mechanical properties and microstructures of Al-SCu-0.5Mg alloy

The mechanical properties and microstructures of Al-8Cu-0.5Mg alloy with and without Ag addition were studied at both room- and elevated-temperatures. The results show that the alloy with Ag is strengthened by a homogeneous distribution of coexistent θ＇ and Ω precipitates on the matrix （001） and （111） planes, respectively, whereas the alloy without Ag by θ＇ precipitates only. The small size and high volume fraction of θ＇ and Ω precipitates in the Ag-containing alloy improve the tensile strength and yield strength, especially those at the elevated temperatures. However, it is also responsible for the decrease in elongation, compared with the alloy without Ag, which is due to the microcracks initiated from the inherent incompatibility between the particles and the AI matrix during deformation.     

用硫代硫酸钠从分银渣中提取银

本文对采用硫代硫酸钠浸出银，连二亚硫酸钠还原银的工艺从分银渣中提取银进行了研究，结果表明：当分银渣中含银量为0．38％，硫代硫酸钠的用量为160kg/t，氨水用量为50L/t，浸出温度60℃，浸出温度为3h，采用二段浸出，其浸出率＞86％，采用连二亚硫酸钠还原银，还原率＞95％，同时，还原后液可再生用于浸出。