Synthesis and electronic property of platinum nanowire and nanoparticle in mesoporous silica template

Platinum nanowires and nanoparticles were selectively synthesized in mesoporous silicas FSM-16 and HMM-1. The nanowires are 3 nm in diameter and several hundred nm to μm in length with high crystallinity. Pt nanowires and nanoparticles can be isolated by dissolving silica matrix with HF. The Pt wires extracted from organosilica HMM-1 have a nanonecklace structure, while the wires from siliceous FSM-16 have a nanorod structure. The extracted Pt nanoparticles (3 nm in size) on HOPG show the Coulomb staircase phenomena in STM/STS analysis. The mechanism for formation of the Pt nanowires is based on the migration of Pt ions in the mesoporous channels.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

Delay time compensation based on coefficient of restitution for collision hybrid motion simulator

A hybrid motion simulator embeds a hardware experiment in a numerical simulation loop. However, it is often subjected to the inherent problem of an energy increase in the collision of two pieces of hardware in a loop because of the delay time. This paper proposes a delay time compensation method based on contact dynamics model for a collision hybrid motion simulator under delay time and establishes a compensation method for coupled translational and rotational motion. The model developed in this paper describes linear uniform motion of a floating object during the period of the delay time until the force and torque are observed and non-linear motion according to environmental stiffness after the initial delay time period in contact. By using the above model, compensation parameters are designed based on desired coefficient of restitution with iterative calculation. The proposed method achieves accurate delay time compensation and simultaneously realizes a variable desired coefficient of restitution over a wide range of frequencies. Furthermore, the compensation method for multi-dimensional motion is established under the assumption that the friction effect is very small. The efficiency of the proposed method is verified through collision experiments for the coupled motion in two dimensions.     

Grafting of poly(ethylene-block-ethylene oxide) onto a vapor grown carbon fiber surface by γ-ray radiation grafting

To modify the surface of vapor grown carbon fiber (VGCF), poly(ethylene-block-ethylene oxide) (PE-b-PEO, M_n=1400, PEO content=50 wt%) was successfully grafted onto the surface by using γ-ray irradiation of the PE-b-PEO-adsorbed VGCF in solvent-free system. It is found that the percentage of polymer grafting reached 15.0% when the PE-b-PEO-adsorbed VGCF was irradiated by γ-ray over 40 kGy dose at 110 °C, but at the lower irradiation temperature of 75 °C, the grafting reaction scarcely proceeded. This indicates that polymer radicals formed by γ-ray irradiation were successfully trapped by VGCF surface above melting point of PE-b-PEO. On the other hand, when the dispersion of VGCF in THF solution of PE-b-PEO was irradiated, the percentage of PE-b-PEO grafting was less than 4.0%. It was confirmed by a field-emission scanning electron microscope (FE-SEM) that the surface of the VGCF was uniformly covered by grafted PE-b-PEO. In addition, the surface free energy of ungrafted and PE-b-PEO-grafted VGCF was determined.     

Effective Coke Removal in Methane to Benzene (MTB) Reaction on Mo/HZSM-5 Catalyst by H2 and H2O Co-addition to Methane

The catalytic dehydro-aromatization reaction over Mo/HZSM-5 catalyst was drastically stabilized by the co-addition of 5.4% H₂ and 1.8% H₂O to methane feed at 750 °C, 0.3 MPa and methane space velocity of 3000 mL g⁻¹ h⁻¹, suppressing the coke formation effectively, compared with single hydrogen or steam addition.     

Performance of solvothermally prepared Ga2O3-Al2O3 catalysts for SCR of NO with methane

The solvothermal reaction of mixtures of aluminum isopropoxide (AIP) and gallium acetylacetonate (Ga(acac)₃) directly yielded the mixed oxides of γ-Ga₂O₃-Al₂O₃. In the solvothermal synthesis, the crystal structure of mixed oxides was controlled by the initial formation of γ-Ga₂O₃ nuclei. The mixed oxides prepared in diethylenetriamine have extremely high activities for selective catalytic reduction (SCR) of NO with methane as a reducing agent. With increasing crystallite size of the spinel structure, the catalytic activity increased. The ratio of the amount of methane consumed by combustion to total methane conversion was proportional to the density of acid sites on the surface of the mixed oxides. The mixed oxide catalysts prepared in diethylenetriamine had lower densities of acid sites and showed a higher methane-efficiency for CH₄-SCR than those prepared in other solvents. These catalysts maintained their high activity even when the reaction was carried out under the severe conditions (i.e., high space velocity and low NO concentration).     

Stabilization of β-Bi2O3 by Sb2O3 Doping

The metastable β form of bismuth sesquioxide was obtained by doping antimony oxide. The solubility of antimony was 4 to 10 at. %in β specimens, where more than 75% of the antimony atoms were valenced at 5+.     

On-chip fabrication of magnetic alginate hydrogel microfibers by multilayered pneumatic microvalves

Alginate hydrogel has widespread applications in tissue engineering, cancer therapy, wound management and drug/cell/growth factor delivery due to its biocompatibility, hydrated environment and desirable viscoelastic properties. However, the lack of controllability is still an obstacle for utilizing it in the fabrication of 3D tissue constructs and accurate targeting in mass delivery. Here, we proposed a new method for achieving magnetic alginate hydrogel microfibers by dispersing magnetic nanoparticles in alginate solution and solidifying the magnetic alginate into hydrogel fiber inside microfluidic devices. The microfluidic devices have multilayered pneumatic microvalves with hemicylindrical channels to fully stop the fluids. In the experiments, the magnetic nanoparticles and the alginate solution were mixed and formed a uniform suspension. No aggregation of magnetic nanoparticles was found, which is crucial for flow control inside microfluidic devices. By regulating the flow rates of different solutions with the microvalves inside the microfluidic device, magnetic hydrogel fibers and nonmagnetic hydrogel fibers were fabricated with controlled sizes. The proposed method for fabricating magnetic hydrogel fiber holds great potential for engineering 3D tissue constructs with complex architectures and active drug release.     

Comparative study on the preparation and properties of radiation‐grafted polymer electrolyte membranes based on fluoropolymer films

In this study the fluoropolymers, poly(ethylene‐co‐tetrafluoroethylene) (ETFE) and poly(vinylidene fluoride) (PVDF) films, together with the radiation‐induced crosslinked polytetrafluoroethylene (cPTFE) film were compared on the basis of their preparation and properties of radiation‐grafted polymer electrolyte membranes. The polymer electrolyte membranes were prepared by radiation grafting of styrene into the base films and subsequent sulfonation. The proton conductivity and chemical stability of the three types of membranes with a similar ion exchange capacity (IEC) near 1.0 mmol/g were investigated and are discussed in detail. Although the ETFE‐based polymer electrolyte membrane was relatively more stable, its proton conductivity was lower than those of the PVDF‐ and cPTFE‐based membranes. On the other hand, the cPTFE‐based membrane showed a significantly higher proton conductivity, but its chemical stability was shorter than that of the ETFE‐based membrane. It is considered that the difference in the preparation and properties of the polymer electrolyte membranes was due to the difference in the degree of crystallinity as well as in the chemical structure of the fluoropolymer base films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1966–1972, 2007     

Synthesis of γ-Ga2O3–Al2O3 Solid Solutions by the Glycothermal Method

The reaction of mixtures of aluminum isopropoxide and gallium acetylacetonate in 1,4-butanediol or 1,5-pentanediol at high temperatures (glycothermal reaction) directly gave the γ-Ga₂O₃–Al₂O₃ solid solutions, which had high catalytic activities for selective reduction of NO using methane as the reducing agent. However, the reaction with a higher Al/(Ga+Al) charged ratio yielded the glycol derivative of boehmite as a by-product and the catalytic activity of the solid solution decreased. Therefore, synthesis of the solid solution using various glycols was examined and it was found that solid solutions with high Al contents without contamination of the glycol derivative of boehmite were obtained by using 1,6-hexanediol as a reaction medium. The solid solution exhibited a higher NO conversion than that synthesized in other glycols.