一种液压摩擦焊机电液系统研究与试验

针对海上石油平台、海底输送管线维修的需要,提供了一种液压摩擦焊机液压和电器系统设计思路,通过参数计算、电液控制系统设计,研发了一种液压摩擦焊机,通过对DH38钢摩擦叠焊单元成型工艺试验,发现焊接接头拉伸强度达到了母材强度的76%以上,验证了液压摩擦焊机的可靠性能,通过该研究的应用,可对海上石油平台、海底输送管线的维修起到积极作用。     

类富勒烯碳薄膜的结构演变及摩擦学性能研究

通过等离子体增强化学气相沉积技术,以不同沉积时间在硅表面上制备类富勒烯碳薄膜,探究类富勒烯碳薄膜结构演变和摩擦学性能随沉积时间变化规律。利用拉曼光谱和透射电子显微镜,考察类富勒烯碳薄膜微结构和表面形貌随沉积时间的变化。结果表明:碳薄膜内类富勒烯结构含量随沉积时间先增加后保持不变;采用沉积时间为3 h的类富勒烯碳薄膜组成摩擦配伍对,当载荷从8 N增加到14 N时,摩擦因数从0.013降至0.006,即随载荷的增加实现了由低摩擦向超滑的转变。这是因为摩擦诱使类富勒烯碳薄膜发生结构转变,并形成有利于减少摩擦的类球状或外部石墨壳层闭合的纳米颗粒。     

考虑结构动态变形的缸套-活塞环润滑建模分析

缸套在燃烧冲击和活塞敲击激励下会产生接近表面粗糙度的动态变形,极有可能影响缸套-活塞环组件间的摩擦润滑过程。为了研究缸套动态变形潜在的影响,将动力学仿真获取的缸套内表面的动态变形经过处理后导入到润滑模型中,同时采用数值积分计算的方式对油液压力应力因子和剪切应力因子进行实时计算求解,使仿真计算更加符合实际情况。通过搭建同时考虑缸套变形与油液剪切特性影响的改进润滑模型,计算得到整个工作循环内活塞环上的最小油膜厚度和摩擦力曲线。结果表明:考虑缸套动态变形后的最小油膜厚度和摩擦力曲线出现了明显的波动,而且考虑缸套动态变形后的摩擦力比未考虑之前出现了明显下降。     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.     

粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

Advanced Friction–Wear Behavior of Organic Brake Pads Using a Newly Developed System

The objective of this study was to investigate the influence of an advanced performance system on the tribological behavior of brake pad material using a specially designed brake pad tester system following standard SAE J-661. The tribological behavior and friction and wear characteristics of the organic brake pad samples were evaluated. During braking tests, the samples, in contact with a cast iron disk, were studied at different disc speeds, temperatures, and braking cycles under a constant pressure. In order to understand the friction and wear behavior, the unworn surfaces, worn surfaces, and wear debris were characterized by means of scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX). Furthermore, the surface characteristics and differences in the wear modes of the brake pad samples were examined. Wear debris was permitted to deform the brake pad surfaces, leading to friction layers and enabling the estimation of the friction behavior of the brake pads. The results showed that the best friction–wear behavior was obtained with lower braking cycles at low speeds and temperature. Thus, the newly developed brake pad tester system proved very effective in evaluating the performance of the brake pad samples.     

Friction Behavior of Human Skin Rubbing against Different Textured Polymeric Materials Obtained by a 3D Printing Microfabrication Technique

Understanding friction behavior of human skin is indispensable in order to optimize surfaces and materials in contact with the skin. The coefficient of friction (COF) for different materials contacting against the skin is mainly influenced by the nature of the materials, mechanical contact parameters, and physiological skin conditions. The aim of the present research work was to study the grip effect of two different polymeric materials by producing different textured patterns using a 3D printing microfabrication technique and a replication technique. It was found that under the same contact conditions, a difference in the friction amplitude exists between the two different polymeric materials and that positive texturing, which consists of high relief or protrusions, showed higher COFs than negative texturing, consisting of low relief, holes, or dimples, which showed a decrease in friction as the textured pattern area density increased.     

Enhancing the Tribological Behavior of Lubricating Oil by Adding TiO2, Graphene,and TiO2/Graphene Nanoparticles

This article investigates the tribological behavior of nanoparticles (NPs) of titanium dioxide anatase TiO₂ (A), graphene, and TiO₂ (A) + graphene added to the pure base oil group ΙΙ (PBO-GΙΙ). The morphology of these two nanostructures of TiO₂ (A) and graphene was characterized by transmission electron microscopy (TEM). Oleic acid (OA) was blended as a surfactant into the formulation to help stabilize the NPs in the lubricant oil. A four-ball test rig was used to determine the tribological performance of six different samples, and an image acquisition system was used to examine and measure the wear scar diameter of the stationary balls. Field emission–scanning electron microscopy (FE-SEM) was used to examine the wear morphology. Energy-dispersive X-ray spectroscopy (EDX), element mapping, and Raman spectroscopy were employed to confirm the presence of (TiO₂ (A) + graphene) and the formation of a tribolayer/film on the mating surfaces. Moreover, a 3D optical surface texture analyzer was utilized to investigate the scar topography and tribological performance. The experiments proved that adding (0.4?wt% TiO₂ (A) + 0.2?wt% graphene) to the PBO-GΙΙ optimized its tribological behavior. These excellent results can be attributed to the dual additive effect and the formation of a tribofilm of NPs during sliding motion. Furthermore, the average reductions in the coefficient of friction (COF), wear scar diameter (WSD), and specific wear rate (SWR) were 38.83, 36.78, and 15.78%, respectively, for (0.4?wt% TiO₂ (A) + 0.2?wt% graphene) nanolubricant compared to plain PBO-GΙΙ lubricant.     

Microstructural and Tribological Behavior of Pulse Electroplated Nickel Barrier on Copper Conductors

The microstructural, mechanical, and tribological behaviors of electroplated Ni on Cu conducting substrates have been investigated in this study. The microstructural studies were performed by X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). The results showed that initially (111) with (220), (200) Ni texture components were predominant in the coating, and increasing the current density from 0.1 to 0.5 A/cm² led to the development of a strong (111) texture. The presence of ultrafine grains coupled with a (111) Ni texture improved the coating microhardness and wear properties significantly. It was shown that with an increase in current density, wear resistance of the coatings improved significantly and the electrical resistivity increased due to the highly populated grain boundaries.