铝电解槽料箱排气管结构的优化改造

简要介绍了铝电解槽料箱排气管在原设计上存在的缺陷和不足，针对缺陷产生的原因进行了结构优化改造。     

Corrosion Control by water‐soluble extracts from leaves of economic plants

Water extracts from leaves of date palm, phoenix dactylifera, henna, Lawsonia inermis, and corn, Zea mays, were tested as corrosion inhibitors for steel, aluminum, copper and brass in acid chloride and sodium hydroxide solutions using weight loss, solution analysis and potential measurements. The inhibition action was found to critically depend on metal type and solution composition. Only, date palm and henna extracts were found highly effective in reducing corrosion rate of steel in acid chloride solutions and aluminum in sodium hydroxide solutions. The inhibition efficiency increased with increasing the concentration of the extract. The inhibition was interpreted in terms of chemisorption of some active ingredients in the leaves according to Temkin isotherm.     

Quantitative assessment of preferential fatigue initiation sites in a multi‐phase aluminium alloy

Complex multi‐phase Al–Sn–Si alloys are commonly employed in the manufacture of small automotive plain bearings. The fundamental fatigue initiation behaviour of this class of alloys is currently not well understood. A range of analytical techniques were applied to investigate preferential initiation site location and to attempt to identify critical microstructural features. It was apparent from experimental studies that points of fatigue crack initiation are associated with the Si secondary phase. Using tessellation approaches and subsequently both adaptive numerical modelling and micro‐scale finite element modelling allowed the identification of features affecting the probability that a given Si phase would initiate a fatigue crack.     

固体推进剂中有关粒度分布的数学处理

介绍了固体推进剂中有关颗粒度分布的数学处理方法，用几种数据统计分析的理论分布函数－正态分布，对数－正态分布，Ｋ分布，并以铝粉和含铝推进剂燃烧残渣的颗粒分布为例进行了分析，根据Ｃｕｌｉｃｋ微粒阻尼的理论计算模型，讨论了粒度分析在阻尼效应计算中的应用。     

铝液夹杂物检测DMIRT－Ⅲ法的试验研究

提出了一种新的铝液夹杂物快速检测方法。导出了该法的检测原理方程。分析并试验研究了影响检测重复性和分辨率的因素。试验选择了较好的检测参数，并获得了较好的检测结果。     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

DV—5光谱测定钢中微量酸溶铝

本文应用贝尔德DV—5光谱仪对钢中微量酸溶铝的测定进行了研究,通过优化仪器参数和控制分析条件等手段,用二次预燃和二次曝光测定酸溶铝,检出限可达0.0015％,该法简便、快速、结果准确。     

再生铝的熔炼设备

介绍了目前我国及世界再生铝的利用及废铝熔炼企业的情况,重点讲述了各种废铝、铝渣(灰)的熔炼工艺流程及国内外先进的熔炼设备.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.