关于正整数的k次根的整部

对于给定的自然数m，令口α（m)为m的是的次根的整部。即：α(m)=[m^1/k]。研究了α(m)的渐近性质，并给出了一个有趣的渐近公式。     

Multi-User MIMO Mobile CDMA Uplink System Employing Turbo Coding and Joint Detection Through a Multipath Rayleigh Fading Channel

In this paper, a generalized multiple-input multiple-output (MIMO) antenna system that can be fitted to the uplink of a wireless communication system is considered for the general case of multi-user. At the transmitter, the information bits are Turbo coded, then interleaved and passed through a serial-to-parallel converter. The channel is assumed bad urban suffering from multipath Rayleigh fading resulting in inter-symbol and multiple access interferences (ISI and MAI). At the front-end of the receiver, a number of receiving antennas are used followed by a joint multi-user estimator based on the Minimum Mean Square Error Block Linear Equalizer (MMSE-BLE).Computer simulations demonstrate a significant performance improvement in both single user and multi-user cases.This paper depends in parts on that presented at the 11th European Wireless Conference, Cyprus, Nicosia, pp. 187–192, April 2005. Yasmine A. Fahmy was born in Guiza, Egypt, on June 4, 1976. She received the B.Sc., M.Sc. and Ph.D. degrees in Communication and Electronics engineering from Cairo University, Egypt on 1999, 2001 and 2005 respectively. She is presently an assistant professor at Cairo University, Egypt. Her current field of interest is wireless communication and channel estimation. Hebat-Allah M. Mourad received her B.Sc., M. Sc. and Ph.D. degrees in electrical communication engineering from Cairo University, Egypt, in 1983, 1987 and 1994 respectively. Since 1983, she has been with the Department of Electronics and Communications, Faculty of Engineering, Cairo University, and is currently associate professor there. Her research interests include optical fiber communications, mobile and satellite communications. Emad K. Al-Hussaini received his B.Sc degree in Electrical Communication Engineering from Ain-Shams University, Cairo, Egypt, in 1964 and his M.Sc and Ph.D. degrees from Cairo University, Giza, Egypt, in 1974 and 1977, respectively. From 1964 to 1970, he was with the General Egyptian Aeroorganization. Since 1970, he has been with the Department of Electronics and Communications, Faculty of Engineering, Cairo University, and is currently professor there. He was a research fellow at Imperial College, London, UK, and at the Moore School of Electrical Engineering, University of Pennsylvania, Philadelphia, PA, USA, in the academic years 1976/1977 and 1981/1982, respectively. In 1990, he received the Egyptian national encouragement award for outstanding engineering research. He has written several papers for technical international journals and conferences. His research interests include signal processing, fading channel communication, modulation, and cellular mobile radio systems. Dr Al-Hussaini is a senior member of IEEE. He is listed in Marquis Whos Who in the World and in the IBC (International Biographical Center, Cambridge) for outstanding people of the 20th century.     

Fatigue crack growth analysis of welded aluminium RHS T-joints with manipulated residual stress level

The fatigue life of a welded aluminium T‐joint made from beams with rectangular hollow section (RHS) has been predicted using a crack propagation analysis and compared with experimental results from joints with different residual stress levels. To include the effect of the residual stresses, the stress ratio was calculated at the weld toe and, via Walker's equation, introduced into the analysis. How to obtain the Walker exponent has been discussed in detail. The introduction of a stress ratio at the weld toe provides good agreement between the experimentally and analytically found S–N curves. The effect of the residual stress was successfully included in the analysis.     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Homology modelling of annexin I: implicit solvation improves side-chain prediction and combination of evaluation criteria allows recognition of different types of conformational error

Annexin I homology models were built from the annexin V crystalstructure. Three methods for side-chain prediction were testedbased on molecular mechanics conformational search, the useof a rotamer database, or a combination of these two methods.We showed that rotamer-based methods were more efficient andthat molecular mechanics energy minimizations, prior to rotamerselection, did not afford clearly improved predictions. Modelsbuilt in vacuo and with an implicit solvation term were comparedwith the annexin I crystal structure which became availableduring the course of this study. The analysis of solvation energies,root mean square deviations, Xi angles and hydrogen bonds showedthat models built with implicit solvation were of better quality.In annexin V, repeat III displays A-B and D-E loop conformationsquite different from other repeats. Since the sequence differencessuggest that repeat III in annexin I might present a conformationsimilar to other repeats, two annexin I models with differentrepeat III conformations were built and compared to determinewhether the correct conformation could have been predicted.We show that using a combination of evaluation criteria, itis possible to discriminate unequivocally between the nativeand the incorrect fold, stressing that only one criterion shouldnot be used to evaluate protein structures.     

Discrete quadratic curvature energies

We present a family of discrete isometric bending models (IBMs) for triangulated surfaces in 3-space. These models are derived from an axiomatic treatment of discrete Laplace operators, using these operators to obtain linear models for discrete mean curvature from which bending energies are assembled. Under the assumption of isometric surface deformations we show that these energies are quadratic in surface positions. The corresponding linear energy gradients and constant energy Hessians constitute an efficient model for computing bending forces and their derivatives, enabling fast time-integration of cloth dynamics with a two- to three-fold net speedup over existing nonlinear methods, and near-interactive rates for Willmore smoothing of large meshes.     

On methods of defuzzification of parametrically represented fuzzy numbers

A comparative analysis of such methods of defuzzification of fuzzy numbers as WABL (Weighted Averaging Based on Levels), centroid, and mean of maxima (MOM) is presented in the study. Analytic formulas are presented for calculating the defuzzification values for parametrically represented fuzzy numbers of triangular and trapezoidal form.     

橡胶挤出机平均温差分析与计算

从理论上推导挤出机平均温差的计算公式，并指出与一般换热器平均温差计算的异同。     

高精度合成地震记录制作技术研究

制作高精度的合成地震记录是精细储层描述的基础，本文在分析合成地震记录原理的基础上，从地震剖面的极性判断、平均速度的选取，反射系数的准确提取，子波的精确估算等方面对制作合成记录的要点进行了分析，通过提高以上四方面的精度，提高了制作合成地震记录的精度，并提出了一套可行的合成地震记录的检查方法。     

加权算术平均与几何平均关系式的新证法

利用函数极小点的性质,得到了若干个正数的加权算术平均与几何平均关系式的新证法