Study on the difference of dispersion behavior between hydrogen and methane in utility tunnel

Compared to liquid/gas hydrogen tank, the pipeline is an economical way for hydrogen transportation. With the quick development of utility tunnel in China, hydrogen pipeline enters the gas compartment can be expected soon. However, all the safety requirements of the gas compartment in the current standards are designed for natural gas, and the applicability for hydrogen is unknown. Therefore, a series of studies were started to investigate the safety of hydrogen in utility tunnel. In this work, a real utility tunnel locates at Shanghai was selected as the physical object. A 3D numerical model was built and successfully validated by a scaled tunnel test. The model has the maximum deviation of +9.5%. After that, a comparatively study of the dispersion behavior of CH₄ and H₂ was conducted. The assumed scenario was a 20 mm small-hole leaks with gauge pressure of 1.0 MPa in the middle of the tunnel. Numerical results shown that, H₂ has a larger dispersion velocity and higher concentration, and is more dangerous compared to CH₄. The current emergency ventilation strategy of air change rate of 12 times/h is not effective enough to dilute the H₂ flammable cloud. The alarm time of the testing points shown strong linear law. There was a sharp variation in the range of 20%–100% LFL (Lower Flammable Limit), so the alarm strategy in the tunnel standards is too ideal for both CH₄ and H₂. The numerical results in the present study could provide a guidance for the design and safety management of the hydrogen tunnel.     

水压爆破拆除超大容积水池

简要介绍了组合式超大容积（８５０ｍ３）水池在水压爆破拆除过程中爆破方案选择、参数选取等方面的经验，并对爆破效果进行了分析，为同类工程施工提供了可借鉴的经验。     

Investigation of liquid water heterogeneities in large area proton exchange membrane fuel cells using a Darcy two-phase flow model in a multiphysics code

Proper management of the liquid water and heat produced in proton exchange membrane (PEM) fuel cells remains crucial to increase both its performance and durability. In this study, a two-phase flow and multicomponent model, called two-fluid model, is developed in the commercial COMSOL Multiphysics® software to investigate the liquid water heterogeneities in large area PEM fuel cells, considering the real flow fields in the bipolar plate. A macroscopic pseudo-3D multi-layers approach has been chosen and generalized Darcy's relation is used both in the membrane-electrode assembly (MEA) and in the channel. The model considers two-phase flow and gas convection and diffusion coupled with electrochemistry and water transport through the membrane. The numerical results are compared to one-fluid model results and liquid water measurements obtained by neutron imaging for several operating conditions. Finally, according to the good agreement between the two-fluid and experimentation results, the numerical water distribution is examined in each component of the cell, exhibiting very heterogeneous water thickness over the cell surface.     

Polysorbate identity and quantity dictate the extensional flow properties of protein-excipient solutions

While protein medications are promising for treatment of cancer and autoimmune diseases, challenges persist in terms of development and injection stability of high-concentration formulations. Here, the extensional flow properties of protein-excipient solutions are examined via dripping-onto-substrate extensional rheology, using a model ovalbumin (OVA) protein and biocompatible excipients polysorbate 20 (PS20) and 80 (PS80). Despite similar PS structures, differences in extensional flow are observed based on PS identity in two regimes: at moderate total concentrations where surface tension differences drive changes in extensional flow behavior, and at small PS:OVA ratios, which impact the onset of weakly elastic flow behavior. Undesirable elasticity is observed in ultra-concentrated formulations, independent of PS identity; higher PS contents are required to observe these effects than in analogous polymeric excipient solutions. These studies reveal novel extensional flow behaviors in protein-excipient solutions, and provide a straightforward methodology for assessing the extensional flow stability of new protein-excipient formulations.     

基于滚动摩擦作用下玉米颗粒在模拟筒仓卸料中的力链分析（网络首发、推荐阅读）

针对颗粒滚动摩擦作用对筒仓中玉米颗粒的力链空间分布进行研究，通过EDEM离散元软件建立筒仓模型与仿真玉米颗粒模型进行卸粮仿真模拟，并与筒仓卸料实验作流态对比，验证模型与仿真结果的准确性。通过对模拟仓进行切片观察和数据处理，对比分析了不同摩擦情况下力链的细观参数随时间演化规律。模拟结果表明：颗粒间摩擦系数越大，卸粮完成的最终时间越长；颗粒间滚动摩擦系数越小，颗粒由整体流转变为管状流的时间越早。对于有漏斗的筒仓来说，减小颗粒间摩擦会改变整体流和管状流之间的极限，从而增加产生管状流的面积。标准滚动摩擦系数下玉米颗粒在卸料过程中会出现起拱-塌陷效应；减小滚动摩擦，玉米颗粒卸料较稳定，未出现起拱的应力突增、以及拱塌陷的应力衰减；增大颗粒间滚动摩擦不但会增加拱效应，且出现成拱高度距离漏斗口更高。     

煤基高能量密度燃料的合成及表征

高能量密度燃料是为新型高性能飞行器提供动力保障的关键,其合成及应用研究具有重要的前瞻性和重大战略意义。煤炭是我国的主体能源和重要原料,通过煤直接转化获取的煤基油,充分保留了煤中特有的环状分子化学结构,具有良好的热安定性和较高的能量密度,被认为是高超音速飞行器的优选燃料。以煤直接液化工艺生产的煤液化石脑油馏分为起始原料,通过富集轻质芳烃、化学合成、催化加氢稳定和产物分离提纯等方法制备煤基高能量密度燃料,并对其产物进行分子结构表征和性能评价。结果表明,煤直接液化生产的石脑油馏分是一种优异的催化重整原料,经催化重整富集轻质芳烃后,其轻质芳烃质量分数高达71.05%。Diels-Alder化学合成主产物是由多个封闭环平面组成且具有空间立体构型的二环或三环烃类物质,质量分数为46.18%,因分子内存在较大的张力能,结构紧凑,其拥有更大的密度和体积热值。煤基高能量密度燃料的密度和体积热值分别为0.8990 g/cm3与38.06 MJ/L,均大大超过现行的国内石油基喷气燃料(RP-3和RP-6)、煤基大比重喷气燃料、美国和俄罗斯军用标准。与单一纯物质合成高能量密度燃料(JP-10和T-10)比较,其密度与体积热值偏小。究其原因主要是轻质芳烃的富集度仅为71.05%,需进一步提高其轻质芳烃质量分数。另外,制备的煤基高能量密度燃料种类复杂,其主产物质量分数仅46.18%,下一步可重点调控合成产物的分子构型和纯化分离。     

菌酶协同改善花生粕的饲用品质

花生粕是重要的蛋白饲料原料，但由于其氨基酸不平衡，特别是精氨酸与赖氨酸比例严重失衡（精氨酸与赖氨酸含量比值在3~4，理想的精氨酸与赖氨酸含量比值为1.0），限制了其在动物养殖中的应用。研究了复合酶预处理结合乳酸菌发酵花生粕对其品质的改善。结果表明：经菌酶协同处理后，花生粕粗蛋白质含量由46.4%提高至506%，大分子蛋白明显降解为小分子蛋白，酸溶蛋白质含量由2.3%提高至17.8%，多肽含量由1.6%提高至15.7%，蛋氨酸和赖氨酸含量分别提高了77.1%和42.0%，精氨酸降解率为18.7%，精氨酸与赖氨酸含量比值从3.7降低至2.1，总酸含量由06%提高到4.7%，其中乳酸含量由0.64 mg/g提高至14.63 mg/g。菌酶协同处理后的花生粕抗氧化性明显增强，其中每克菌酶协同处理后的花生粕对羟自由基的清除能力与171.6 mg VC相当，比花生粕（与47.6 mg VC相当）提高了2.6倍。     

Non-keyhole Friction Stir Welding for 6061-T6 Aluminum Alloy

A novel non-keyhole friction stir welding technique was proposed to weld the butt joint of 6061-T6 aluminum alloy with the thickness of 6 mm. A sound joint was obtained by this technique, simultaneously eliminating the flash, shoulder mark and keyhole defects. The sleeve directly affected zone (SDAZ) and the sleeve indirectly affected zone (SIAZ) were divided into the joint according to the plunging position of the hollow sleeve. The lack of root penetration defect was avoided when the plunging depth of the hollow sleeve was only 4.2 mm, because the hollow part inside the sleeve improved the material flow below the sleeve. An S-shaped line was left at the SIAZ, and the height of it had the minimum value of 1.47 mm at 20 mm/min. Whether the failure location of the joint was in SIAZ/SDAZ or the heat-affected zone (HAZ) depended on the height and bonding strength of the S-shaped line. The joint fracture location changed from the SIAZ/SDAZ at 35 mm/min to the HAZ at 20 and 30 mm/min. The maximum tensile strength of 224.3 MPa was obtained at 30 mm/min which was 73.7% of that of the base material. The fracture surface morphology exhibited the typical ductile fracture.     

汽车密封件双料一体旋转模具设计

针对PP+TPE汽车密封件设计了大型双料一体旋转注射模,介绍了二次合模的精确定位、可控注射系统、顶出平衡设计。该模具技术能够使两种性能完全不同的材料按照指定区域分布,并且达到塑件尺寸的精度需求,实现同时与钣金、玻璃、塑件等不同材质的零件进行复合配套。本项目实施后,在模具精度、寿命等方面接近或部分达到国外同类产品先进水平,而价格仅为国外产品的40%,性价比优势明显。