Deploy Efficiency Driven k-Barrier Construction Scheme Based on Target Circle in Directional Sensor Network

Journal of Computer Science and Technology - With the increasing demand for security, building strong barrier coverage in directional sensor networks is important for effectively detecting...     

复合酶法提取黄秋葵可溶性膳食纤维的工艺优化及其理化特性、结构表征

以黄秋葵果荚为原料,采用复合酶法提取可溶性膳食纤维(soluble dietary fiber,SDF),通过单因素实验,探究不同因素对黄秋葵SDF得率的影响。在单因素实验的基础上进行响应面分析,得到复合酶法制备黄秋葵SDF的最优条件;并测定所得黄秋葵SDF的理化特性,并对其进行结构表征。结果表明:在料液比1:24 g/mL、复合酶添加量1.8%、酶解时间54 min、酶解温度62℃的提取条件下,黄秋葵SDF得率达到最大值,为10.94%,与预测值之间的相对误差为1.48%。黄秋葵SDF的持水力、膨胀力和持油力分别为5.61 g/g、3.35 mL/g和4.88 g/g,良好的理化特性使其具有成为通便保健食品原料的潜力。黄秋葵SDF的微观结构显示,经过酶的作用,黄秋葵SDF表面的淀粉类物质被充分除去;黄秋葵SDF的晶体结构符合纤维素I晶型的特征,其红外光谱图线符合膳食纤维类物质的典型特征。     

Microwave dielectric properties of SrLa[Ga1−x(Mg0.5Ti0.5)x]O4 and SrLa[Ga1−x(Zn0.5Ti0.5)x]O4 (x = 0.2-0.8) ceramics

SrLa[Ga_1−x(R_0.5Ti_0.5)_x]O₄ (R = Mg, Zn) ceramics were prepared by a standard solid state sintering method. The single-phase ceramics with K₂NiF₄-type layered perovskite structure and I4/mmm space group were obtained, indicating that SrLa(R_0.5Ti_0.5) and SrLaGaO₄ can form the unlimited solid solutions. With increasing x for R = Mg and Zn, ε_r increases monotonously, the Qf value first increases and then decreases, while τ_f increases from a negative to a positive value. The optimized microwave dielectric properties were obtained as following: ε_r = 23.3, Qf = 89 400 GHz, τ_f = −0.8 ppm/°C for SrLa[Ga_0.6(Mg_0.5Ti_0.5)_0.4]O₄ and ε_r = 23.3, Qf = 76 200 GHz, τ_f = 0.2 ppm/°C for SrLa[Ga_0.7(Zn_0.5Ti_0.5)_0.3]O₄, indicating that the present solid solution ceramics are the promising candidates as microwave resonator materials for the telecommunication applications.     

Effect of nano-vanadium nitride on microstructure and properties of sintered Fe-Cu-based diamond composites

With FeCu₃₀ pre-alloy powder as the main component of the bond, a new type of nano‑vanadium nitride (VN) additive with different concentrations was introduced into Fe-Cu-based diamond composites to investigate the effect of nano-VN on the microstructure and properties of Fe-Cu-based diamond composites. The hardness, relative density, bending strength and wear loss weight of the fabricated specimens were tested, and then the fracture surfaces and worn surfaces of those specimens were analyzed using scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). The results show that the Fe-Cu-based diamond composites with nano-VN addition exhibited an improvement in the mechanical properties, plasticity and wear resistance, which can be attributed to the dispersion strengthening and grain refinement caused by nano-VN. And the nano-VN can also activate sintering, which can significantly improve the wettability of the binder to diamonds, resulting in more binder elements wetting and diffusion on the diamond surface during the sintering process. Besides, the diamond composites showed the best properties with the addition of 2% nano-VN. That is, the bending strength and the HRB hardness of the diamond composites increased by 25% and 20%, respectively, and the wear resistance of the matrix and holding force coefficient of the matrix to diamond were improved significantly. But an excessive amount of nano-VN was detrimental to the mechanical properties of Fe-Cu-based diamond composites.     

Automatic sorting of fresh tea leaves using vision-based recognition method

Mechanical tea harvesting using plucking machines is highly efficient, but harvested raw fresh tea leaves (FTLs) are always low quality because they contain a mixture of old leaves and leaf debris. To address this problem, this study developed an automatic sorting machine with a vision-based recognition method to extract high-quality FTLs from plucked raw FTLs. First, the raw FTLs were separated one by one after passing through three sequential conveyor belts with increasing speed, and were then classified into four grades using a vision-based recognition method. Finally, the FTLs were blown by air nozzles into collection boxes according to their specific grade. In the recognition method, the shape-based feature of each FTL is extracted by establishing the FTL's topological structure, and the support vector machine model is used for classification. The experimental results revealed that the vision-based recognition method performed satisfactorily with an accuracy rate of 94% and precision rate of 85%. The sorting success rate and efficiency of the automatic sorting machine were approximately 80% and 15 kg hr⁻¹, respectively. The results indicate that the developed automatic sorting machine can effectively and efficiently sort raw FTLs, which may improve the profitability and promote the automation of tea processing.     

Elasticity solution for the casing under linear crustal stress

The integrity of the casing is crucial for oil and gas well. Based on stress function method, a three-dimensional model of the casing-cement sheath-formation system subjected to linear crustal stress is proposed. And then an analytical solution of the model was obtained. In the process of calculation, the casing and cement sheath are simplified as the perfect cylinder. The cement sheath is closely bonded with the casing and formation. The formation is considered to be an isotropic material without the layer-block structure. And the crustal stress is assumed to be linearly increasing with the depth of the well. The analytical solution strictly meets the stress and displacement continuity condition and boundary condition, and exhibits good agreement with finite element method. The results imply that an analytical method to capture the stress and displacement field of the casing under linear crustal stress along the axis is presented. Next, a benchmark for numerical and approximate solutions is provided. In addition, a new idea about solving the casing under the non-linear loads along the axis in some special stratum (such as heterogeneity stratum, salt rock) is proposed. Finally, our understanding for the casing under complex loads will be deepened.     

[成形过程仿真优化与集成计算材料工程]限定加热管布局的快速热循环注塑成形模具电加热系统优化

针对管道布局、最大允许能耗给定条件下快速热循环注塑成形（RHCM）注塑模具型腔表面快速均匀加热的问题，提出以单根加热棒热流密度为设计变量，以模具型腔表面升温效率和温度分布均匀性为目标，结合有限元模拟、响应面设计以及多目标粒子群优化技术来优化RHCM模具电加热系统。与优化前相比，加热系统优化后，模具型腔表面最大温差降低63.4%，加热系统总能耗降低9%。对比了不同注塑成形工艺条件下成形的平板塑件表面质量，结果表明，相对传统注塑成形（CIM）工艺，RHCM工艺将制品表面粗糙度Ra从320 nm降低到118 nm，并有效抑制了制品表面熔接痕、缩痕等缺陷；发现制品表面粗糙度与型腔表面对应点温度成负相关，说明优化后的型腔表面温度分布更有利于提升制品表面质量。