Profiles of mean wind speeds and vertical turbulence intensities measured at seashore and two inland sites using Doppler sodars

The authors’ group has been conducting full-scale measurements of wind velocities with Doppler sodars. It is very important to accurately assess the profiles of mean wind speeds and turbulence intensities in relation to terrain roughness. In this study, the profiles were evaluated for all data measured over a long period at a seashore and two inland sites. It is confirmed that for strong winds the profiles can be approximated by a single power law at altitudes between 50 and 340 m. The power law exponents of the mean wind speed profiles are approximately 0.1 for wind from the sea and 0.2-0.3 for wind blown over land. Those of the turbulence intensity profiles are approximately 0 and −0.2 to 0.4, respectively.     

A parametric, experimental analysis of conical vortices on curved roofs of low-rise buildings

Different methods to reduce the high suction caused by conical vortices have been reported in the literature: vertical parapets, either solid or porous, placed at the roof edges being the most analysed configuration. Another method for alleviating the high suction peaks due to conical vortices is the use of some non-standard parapet configuration like cantilever parapets. In this paper the influence of roof curvature on the conical vortex pattern appearing on a curved roof (Fig. 1) when subject to oblique winds is experimentally analysed by testing the mean pressure distribution on the curved roofs of low-rise building models in a wind tunnel. Also, the efficiency of cantilever parapets to reduce mean suction loads on curved roofs is experimentally checked. Very high suction loads have been measured on curved roofs, the magnitude of these high suction loads being significantly decreased when cantilever parapets are used. Thus, the suitability of these parapets to reduce wind pressure loads on curved roofs is demonstrated.     

Improved dynamic analysis of structures with mechanical uncertainties under deterministic input

This paper addresses the dynamic analysis of linear systems with uncertain parameters subjected to deterministic excitation. The conventional methods dealing with stochastic structures are based on series expansion of stochastic quantities with respect to uncertain parameters, by means of either Taylor expansion, perturbation technique or Neumann expansion and evaluate the first- and second-order moments of the response by solving deterministic equations. Unfortunately, these methods lead to significant error when the coefficients of variation of uncertainties are relatively large. Herein, an improved first-order perturbation approach is proposed, which considers the stochastic quantities as the sum of their mean and deviation. Comparisons with conventional second-order perturbation approach and Monte Carlo simulations illustrate the efficiency of the proposed method. Applications are discussed in order to investigate the influence of mass, damping and stiffness uncertainty on the dynamic response of the system.     

A small sample comparison of maximum likelihood, moments and L-moments methods for the asymmetric exponential power distribution

Three methods of estimation, namely maximum likelihood, moments and L-moments, when data come from an asymmetric exponential power distribution are considered. This is a very flexible four-parameter family exhibiting variety of tail and shape behaviours. The analytical expression of the first four L-moments of these distributions are derived, allowing for the use of L-moments estimators. A simulation study compares the three estimation methods in small samples.     

Safety system logic solver availability, 1oo2D and TMR

Four simplifications in the calculation of safety instrumented system logic solver performance measures (mean time to failure and risk reduction factor) clarify the dependence on the various factors involved. These include failure rate, fail safe fraction, diagnostics coverage and common cause. Approximate MTTF and RRF formulas are developed for 1oo2D and TMR logic solvers. These provide an explicit indication of which factors have the greatest influence on improving safety.     

一起小剂量γ外照射事故剂量估算

本文叙述了一起小剂量γ外照射事故的情况。对受照射的六名男性儿童(9—12岁)给出了性腺剂量(9.5×10~(-3)—1.4mGy)和躯干中线平均剂量(2.6×10~(-2)—10×10~(-2)mGy。)     

次模拟裂变中子源能谱测量

一、引言次模拟和模拟裂变中子源用于研究链式反应系统的各种性质,所以这些中子源的能谱测量是很重要的。源材料、源包壳材料和工艺过程不同,中子源能谱也不同,因而在制作过程中,对源中子能谱的监测是十分必要的。这些中子源的能量一般是几百keV,这一能区连续中子能谱测量一直是很困难的。中子飞行时间法不适于本工作;阈探测器活化法在     

Optimization of a hospital room by means of CFD for more efficient ventilation

This paper analyses the ventilation airflow pattern in a two-bedded hospital room. The whole space of the room is divided in modules by means of curtains and internal partition walls. This configuration has many advantages from the point of view of comfort and medical assistance, but it implies an important restriction as far as ventilation is concerned. The ventilation system consists of an induction unit placed inside the hall ceiling blowing into the room and an exhaust fan in the bathroom. Numerical model solves mass, momentum and mean age of air equations assuming isothermal and stationary flow. Ventilation is evaluated analysing the age of air and the velocity fields inside the room. The results with the initial architectural design of the room show a very deficient ventilation at the patients site. Alternative configurations have been studied, allowing for correct ventilation without renouncing to the assistance advantages. Finally, the optimum configuration of the room is provided, regarding both the comfort of the patients and the cost of execution.     

Experimental investigation of mixing-enhanced swirl flows

The experimental objective was to compare disintegration characteristics from the internal mixing pneumatic nozzles under the different operating conditions in terms of swirl angles. For this investigation, supplied air pressures and nozzle configuration ratios were fixed. This experimental comparison is of fundamental importance to the understanding and modeling of turbulent atomization because the axisymmetric swirling flows involve relatively complex interactions. For the measurement, four internal swirl mixing nozzles with axisymmetric holes at swirl angles of 15°, 30°, 45°, and 60° to the central axis were employed, which is responsible for the enhancement of mixing in pneumatic jets. To illustrate the swirl phenomena quantitatively, the distributions of mean velocities, turbulence intensities, and SMD (Sauter mean diameter, or D₃₂) variations with different configuration ratio were comparatively analyzed. It indicated that the atomization characteristics are performed well in the case of 30° of swirl angle, and that turbulence intensities are gradually degenerated with the increase of radial distances, showing a slight increment of SMD at downstream region. In particular, measurements showed that nozzle configuration is one of the significant geometrical parameters affecting the spray trajectories. This paper was recommended for publication in revised form by Associate Editor Jun Sang Park