湿法聚氨酯树脂浆料配方的改进

通过对湿法PU合成革用聚氨酯(PU)树脂浆料配方的改进，降低了浆料的生产成本，浆料的后期加工性能提高，并且PU膜的性能也有所改善。     

TiO2光催化膜的成膜技术

综述了TiO2光催化膜的各种成膜方法及其进展，其中包括在陶瓷玻璃等耐热基材上的TiO2烧结法、近年来发展很快的用于塑料等非耐热性材料的粘合剂成膜法，以及用于无纺布的抄造法和水泥的混练法等。     

浆料系统内上升气泡周围微细颗粒浓度分布和附着效率的理论研究

Quantitative prediction of distribution function and adhesion efficiency of particles around a rising bubble in slurry systems is presented in this work. By solving the convection-diffusion equation (Fokker-Planck equation), the influence of Brownian diffusivity of fine particles on concentration distribution and adhesion efficiency is demonstrated with the hydrodynamic force and van der Waals attractive potential between particles and bubble considered. It is found that two kinds of mechanism dominate the adhesion process of particles on bubble according to different Peclet number or size of particles and bubble, as well as other properties of the slurry systems. In addition, the viscosity ratio of bubble to the suspending fluid was found to have obvious influence on particle adhesion.     

PTA生产中浆料浓度的先进控制

在PTA生产过程中,TA浆料浓度是一个极其重要的工艺变量,该变量控制的好坏直接影响最终产品的产量和质量。首先分析了浆料浓度的特性,然后根据其特性提出了非线性补偿+预测控制的先进控制策略。实际应用表明,这一控制策略可以显著减少浆料浓度波动、提高装置处理能力。     

球形磷酸铁锂材料的制备及其18650电池的测试

采用高能球磨和喷雾干燥法制备了球形磷酸铁锂材料LFP-1,并制作18650实装电池,测试电极片的压实密度,同时选择一种商业化磷酸铁锂材料LFP-2作为对比。测试结果显示,2种LFP材料均由平均粒径为300~500 nm的一次颗粒组成,比表面积为13~15 m²/g,碳质量分数为1.5%左右。通过CR2032纽扣型电池充放电测试表明,在0.2C时,LFP-1的比放电容量约为165 mA·h/g,与商业化磷酸铁锂材料LFP-2相近。制备18650电池的结果表明,商业化磷酸铁锂LFP-2材料制备的电极片的最高压实密度可以达到2.52 g/cm³,显著高于实验室制得的磷酸铁锂材料LFP-1的最高压实密度2.25 g/cm³,这可能与材料的颗粒粒度分布不同有关。     

Microscopic characterization of semi-solid aluminium alloys

The microstructural evolution and element distribution of the Al-4Cu-Mg alloy during semi-solid compression were investigated,and the precipitate behavior and dislocation morphology were discussed.The experimental results show that the microstructure,the number of CuAl2(θ phase) precipitates,and the dislocation density of the Al-4Cu-Mg alloy depend apparently on the process parameters.More segregation of Cu at the grain boundary happens with an increase of deformation temperature and a decrease of strain ra...     

聚酰亚胺复合杂化环氧树脂基增强浆料的制备与性能研究

采用溶胶-凝胶技术,在合成的聚酰胺酸(PAA)中对纳米SiO2/TiO2前驱体进行原位改性,添加硅烷偶联剂(WD-50),利用超声空化及复配技术制备了环氧树脂基-SiO2.TiO2复合杂化聚酰亚胺增强浆料,并采用FTIR、DSC、粒径分析仪、力学测试、STM等手段对所制备增强浆料的性能及其在碳纤维上浆膜铺展的显微形貌进行了分析.结果表明:SiO2.TiO2以纳米粒度分布于浆膜中;上浆后碳纤维轴向界面有一层纳米级粒状突起,表面较为粗糙,改善了碳纤维的界面性能,杂化浆料处理后碳纤维的抗拉强度及层间剪切强度显著提高.     

明胶蛋白助剂在纺织与染整中的应用

论述了明胶蛋白助剂在纺织和染整中的不同分类及其特点等,并探讨了其发展趋势。     

镁合金液态精密成型研究进展

介绍了镁合金液态精密成型技术的研究进展,包括镁合金熔炼气体保护,熔体净化、细化,镁合金压铸、挤压铸造、消失模铸造和半固态加工的研究成果,展示了镁合金广阔的应用前景.最后,对镁合金液态精密成型技术的发展方向作了展望.     

Microstructure and properties of electronic packaging shell with high silicon carbide aluminum-base composites by semi-solid thixoforming

The electronic packaging shell with high silicon carbide aluminum-base composites was prepared by semi-solid thixoforming technique. The flow characteristic of the Si C particulate was analyzed. The microstructures of different parts of the shell were observed by scanning electron microscopy and optical microscopy, and the thermophysical and mechanical properties of the shell were tested. The results show that there exists the segregation phenomenon between the Si C particulate and the liquid phase during thixoforming, the liquid phase flows from the shell, and the Si C particles accumulate at the bottom of the shell. The volume fraction of Si C decreases gradually from the bottom to the walls. Accordingly, the thermal conductivities of bottom center and walls are 178 and 164 W·m-1·K-1, the coefficients of thermal expansion（CTE） are 8.2×10-6 and 12.6×10-6 K-1, respectively. The flexural strength decreases slightly from 437 to 347 MPa. The microstructures and properties of the shell show gradient distribution.