Ca1-3x/2Al2Si2O8:xEu3+荧光粉的发光和光温传感特性

为了探究稀土离子掺杂铝硅酸盐的光温特性,本文采用燃烧合成法制备了系列荧光粉材料Ca_1-3x/2Al₂Si₂O₈:xEu³⁺。X射线衍射结果表明掺杂Eu³⁺离子不会改变基质CaAl₂Si₂O₈的晶体结构。荧光光谱结果表明该荧光粉在近紫外光区域具有较强吸收,当被波长为393 nm的近紫外光激发后,其最大特征发射峰为611 nm,且Eu³⁺离子的最佳掺杂浓度为0.05。利用上升时间测温法研究了CaAl₂Si₂O₈:Eu³⁺荧光粉的光温传感特性,结果表明:随着Eu³⁺掺杂浓度的增加,上升时间单调递减,但当掺杂掺杂超过0.100时就会发生淬灭。Ca_0.985Al₂Si₂O₈:0.01Eu³⁺的相对灵敏度随温度的升高先增大后减小,并在520 K时达到最大值（0.024 K^-1）。上述研究表明该荧光粉具备优异的温度传感性能,在测温领域具有广泛的应用前景。     

Potential Antitumor Effects of 6-Gingerol in p53-Dependent Mitochondrial Apoptosis and Inhibition of Tumor Sphere Formation in Breast Cancer Cells

Hormone-specific anticancer drugs for breast cancer treatment can cause serious side effects. Thus, treatment with natural compounds has been considered a better approach as this minimizes side effects and has multiple targets. 6-Gingerol is an active polyphenol in ginger with various modalities, including anticancer activity, although its mechanism of action remains unknown. Increases in the level of reactive oxygen species (ROS) can lead to DNA damage and the induction of DNA damage response (DDR) mechanism, leading to cell cycle arrest apoptosis and tumorsphere suppression. Epidermal growth factor receptor (EGFR) promotes tumor growth by stimulating signaling of downstream targets that in turn activates tumor protein 53 (p53) to promote apoptosis. Here we assessed the effect of 6-gingerol treatment on MDA-MB-231 and MCF-7 breast cancer cell lines. 6-Gingerol induced cellular and mitochondrial ROS that elevated DDR through ataxia-telangiectasia mutated and p53 activation. 6-Gingerol also induced G0/G1 cell cycle arrest and mitochondrial apoptosis by mediating the BAX/BCL-2 ratio and release of cytochrome c. It also exhibited a suppression ability of tumorsphere formation in breast cancer cells. EGFR/Src/STAT3 signaling was also determined to be responsible for p53 activation and that 6-gingerol induced p53-dependent intrinsic apoptosis in breast cancer cells. Therefore, 6-gingerol may be used as a candidate drug against hormone-dependent breast cancer cells.     

TEM and DFT investigation of CVD TiN/κ-Al2O3 multilayer coatings

This paper investigates the interfacial structure in hot-wall CVD TiN/κ-Al₂O₃ multilayer coatings using both HREM and DFT modeling. Two multilayers with different thicknesses of the TiN layers (50 and 600 nm) separating the κ-Al₂O₃ layers are analyzed. The general microstructure of the two multilayers is relatively similar. The TiN layer in the thicker TiN/κ-Al₂O₃ coating is thick enough to be several TiN grains high. This means that epitaxial columns, which are often found in the thinner TiN/κ-Al₂O₃ coatings, are not present. However, the orientation relationships at the TiN/κ-Al₂O₃ interfaces are the same in both multilayers. The HREM investigations show that κ-Al₂O₃ (001) planes can grow directly on flat (111) TiN faces, without any other phases or detectable amounts of impurities, such as sulphur, present. Where the TiN layers are more curved, γ-Al₂O₃ can be grown, at least partly stabilized by the cube-on-cube orientation relationship between γ-Al₂O₃ and the underlying TiN. The DFT calculations show very similar adsorption strengths for an O monolayer positioned on Ti-terminated TiC(111) and TiN(111) surfaces, with preferred adsorption in the fcc site. O adsorption on N-terminated TiN(111) is much weaker, with preferred adsorption in the top site. Calculated elastic-energy contributions yield a higher stability for κ-Al₂O₃ on TiN(111) than on TiC(111) and a higher stability for κ-Al₂O₃ than for α-Al₂O₃ on both TiC and TiN. This indicates that the observed higher stability of κ-Al₂O₃ on TiC(111) than on TiN(111) is not due to the lattice mismatch, while the preferred epitaxial growth of κ-Al₂O₃ over α-Al₂O₃ can be partly attributed to the mismatch.     

00Crl8Nil0N奥氏体不锈钢200 - 600℃高温疲劳性能的研究

试验用00Cr18Ni10N钢（/%:0.018C,0.41Si,1.68Mn,18.18Cr,10.38Ni,0.16N）经1t EAF-AOD-ESR冶炼,锻成Φ30 mm材和1 050℃固溶处理,进行了00Cr18Ni10N钢200～600℃光滑（K_t=1）、缺口（K_t=3）的轴向高周疲劳性能研究,绘制了疲劳S-N曲线、计算了疲劳极限,并对疲劳试样的典型断口进行了SEM观察。结果表明,光滑试样的疲劳极限随试验温度升高而降低,缺口试样的疲劳极限对试验温度变化不敏感。当应力集中系数由K_t=1提高到K_t=3时,00Cr18Ni10N钢的200、400、600℃下10⁷周次条件疲劳极限分别从530、506、410 MPa,降低到323、370、392 MPa。表明在高温下00Cr18Ni10N钢存在疲劳极限对应力集中敏感,且应力集中敏感性随着试验温度的升高而降低。疲劳试样的断口形貌由疲劳源区、疲劳裂纹扩展区和瞬断区组成,疲劳起源于表面加工刀痕的不连续位置,呈韧性断裂特征。     

Ca对原位自生Mg2Si/ZM5复合材料组织与性能的影响

通过真空感应炉中氩气保护,在ZM5熔体中加入Si获得原位反应自生Mg2Si/ZM5复合材料.采用金相显微镜、环境扫描电镜、拉伸实验等研究了Ca对该材料组织与性能的影响规律.结果表明:Ca的加入改变了Mg2Si/ZM5复合材料中Mg2Si相的形貌,使其从不规则的汉字状变成较细小的多角形,从而改善了材料的力学性能;当加入0.05?(质量分数)时,复合材料的室温力学性能最好,屈服强度提高了10.4%,延伸率提高了52.4%;在200℃高温下,当含Ca0.05%～0.10%(质量分数)时其屈服强度和延伸率最好,分别提高了30.1%和92.3%.     

反应堆A0纯铝的点蚀模拟

测量A0纯铝在去离子水中的极化曲线用来模拟反应堆池壳的点蚀.研究表明A0纯铝在去离子水中很容易钝化.实验中用美国EG&G普林斯顿应用研究公司生产的273型恒电位/恒电流仪测量模拟孔电位,极化曲线表明模拟腐蚀坑处于钝化状态,即便是氧化膜破裂,腐蚀坑也发展得很慢.用pH计测量孔中pH的变化,并得到其工作曲线,此曲线表明带有氧化膜的点蚀坑坑内存在明显的酸化现象.并对A0铝池壳的服务寿命进行了估计.     

锡磷青铜合金水平连铸工艺参数的优化

铸造锡磷青铜合金组织中存在显微缩松、枝晶偏析和反偏析是冷加工报废的主要原因.通过连铸工艺参数的正交实验,建立了轧制成材率与主要工艺参数之间的神经网络描述,网络模型与遗传算法结合对工艺参数的组合进行了优化,改善了铸坯的组织,提高了轧制带材成材率.     

Influence of expandable graphite on fire resistance and water resistance of flame-retardant coatings

Expandable graphite (EG) coating and ammonium polyphosphate-pentaerythritol-melamine (APP-PER-MEL) coating were prepared. Thermal degradation and char formation of the coatings were investigated by differential thermal analysis (DTA), thermogravimetry (TG), X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The results have shown that the anti-oxidation and fire-resistant properties of expandable graphite coating containing EG with size of 74 μm are better than those of APP-PER-MEL coating. The static immersion test was applied to study water resistance of the coatings, and the fire protection test and mechanical test were used to analyse heat insulation and mechanical properties of coatings before and after water immersion. The fire-resistant and mechanical properties of APP-PER-MEL coating were severely damaged by water immersion, whereas EG coating containing 8.5% EG with size of 74 μm could retain the good fire resistance even after 500 h water immersion.     

Fluorinated Polyphosphazenes: A Survey

A general survey of fluorinated phosphazene polymers starting from their synthesis in 1965 to recent times is presented. Various types of fluorinated phosphazenes are described depending on the way fluorine atoms are connected to the polyphosphazene skeleton. The characterization, properties and practical utilization of these compounds in different domains are critically discussed.     

Enhancement by SO2 of initial activity for selective catalytic reduction of NO with CH3OH over \gamma-alumina

The effect of SO₂ on catalytic activity for NO reduction to N₂ by methanol in excess oxygen over $\gamma$ -alumina has been investigated. SCR activity increased initially upon exposure of a fresh $\gamma$ -alumina catalyst to SO₂ which is attributed to formation of Brønsted acid sites. Longer exposure to SO₂ leads to a decline in catalytic activity to a lower steady-state NO_x reduction activity which is independent of the SO₂ content in the feed gas.