Combustion synthesis of NbC/ZrO2 composites: Influence of Cr additives on the microstructure and mechanical properties

Composites of NbC/ZrO₂ reinforced with different weight ratios of Cr metal were prepared by dynamic compaction combustion from a blend of Nb₂O₅–Zr–Cr powders. Factors controlling the synthesis process, the microstructure, and the mechanical properties of the samples, such as Cr wt% and the compression loads were studied. The samples were characterized by XRD, SEM, porosity, and hardness measurements. The porosity value of the sample with no additives was high and reached 31.6 vol%. A sudden decrease in the sample porosity to 2.4 vol % was noticed for the sample containing 3.0 wt% of Cr. A high-density sample with less than 2.0 vol % porosity and maximum hardness of 1038 HV was produced using 5.0 wt% Cr under 300 MPa compression load. Detailed thermodynamic calculations for the effect of Cr additives on the physicochemical properties of the system were introduced.     

The Impact of Metastable Intermolrecular Nanocomposite Particles on Kinetic Decomposition of Heterocyclic Nitramines Using Advanced Solid‐Phase Decomposition Models

Journal of Inorganic and Organometallic Polymers and Materials - Surface oxygen of oxide catalyst has low coordination number; they are negatively charged. Surface oxygen can act active site for...     

Electrochemical behaviour of Mn3+/Mn2+, Co3+/Co2+ and Ce4+/Ce4+ redox mediators in methanesulfonic acid

The redox behaviour of Mn³⁺/Mn²⁺, Co³⁺/Co²⁺ and Ce⁴⁺/Ce³⁺ mediators commonly used in indirect oxidation of organic compounds were evaluated in methane sulfonic acid on a glassy carbon working electrode employing cyclic voltammetry. Manganic methanesulfonate exhibits higher instability in dilute methanesulfonic acid. The solid MnO₂ formed during disproportionation on the glassy carbon electrode further affects the reproducibility. Cobaltic methanesulfonate formation occurs only at oxygen evolution region rendering the overall oxidation process less efficient. Ceric methane sulfonate formation is highly efficient over a wide acid concentration range. Ceric methanesulfonate can also be employed over a wide temperature range to oxidize different aromatic compounds.     

The lime-silica-water system: Equilibria at bulk calcium/silicon ratios of 1·5–2·5 AT 180–250°C

The stability relationships of xonotlite, foshagite and hillebrandite relative to kilchoanite and calcio-chondrodite have been studied under saturated steam pressures at 180° and 250°. Kilchoanite was unstable relative to xonotlite plus hillebrandite at 180°, or to foshagite plus hillebrandite at 250°; calcio-chondrodite was unstable relative to hillebrandite plus some more lime-rich phase, possibly Ca(OH)₂, at both temperatures. Foshagite was stable relative to xonotlite plus hillebrandite at 250°, but unstable relative to these phases at 180°.     

Barium aluminate hydrates. IV. α-BaO.Al2O3.4H2O

α-BaO.Al₂O₃.4H₂O has been synthesised and studied by infrared, X-ray and thermal analytical techniques. The compound of approximate formula BaO.Al₂O₃.0.5H₂O, described in Part III, forms as a dehydration product, and appears to be identical with the compound β-BAH₂ described by other workers. A possible explanation for the discrepancy in water content is discussed.     

PRIVACY LEAKAGE IN HEALTH SOCIAL NETWORKS

Members of health social networks may be susceptible to privacy leaks by the amount of information they leave behind. The threat to privacy increases when members of these networks reuse their pseudonyms in other social networks. The risk of re‐identifying users from such networks requires quantitative estimates to evaluate its magnitude. The estimates will enable managers and members of health social communities to take corrective measures. We introduce a new re‐identification attack, the social network attack, that takes advantage of the fact that users reuse their pseudonyms. To demonstrate the attack, we establish links between MedHelp and Twitter (two popular social networks) based on matching pseudonyms. We used Bayesian networks to model the re‐identification risk and used stylometric techniques to identify the strength of the links. On the basis of our model 7‐11. 8% of the MedHelp members in the sample population who reused their pseudonyms in Twitter were re‐identifiable compared with 1% who did not. The risk estimates were measured at the 5% risk threshold. Our model was able to re‐identify users with a sensitivity of 41% and specificity of 96%. The potential for re‐identification increases as more data is accumulated from these profiles, which makes the threat of re‐identification more serious.     

Molecular solutions for minimum and exact cover problems in the tile assembly model

The tile assembly model is a novel biological computing model where information is encoded in DNA tiles. It is an efficient way to solve NP-complete problems due to its scalability and parallelism. In this paper, we apply the tile assembly model to solve the minimum and exact set cover problems, which are well-known NP-complete problems. To solve the minimum set cover problem, we design a MinSetCover system composed of three parts, i.e., the seed configuration subsystem, the nondeterministic choice subsystem, and the detection subsystem. Moreover, we improve the MinSetCover system and propose a MinExactSetCover system for solving the problem of exact cover by 3-sets. Finally we analyze the computation complexity and perform a simulation experiment to verify the effectiveness and correctness of the proposed systems.     

Particle-Substrate Collisions, Particle Rebound and Removal

Recent progress in particle capture and rebound and its effect on the adhesion force is reviewed in this paper. Particles rebound when the incident velocity is greater than a characteristic critical velocity. Lower impaction velocity particles experience elastic and plastic deformation. Recent models for particle rebound and capture are discussed and evaluated in terms of their restrictive assumptions and results. Recent experimental data of particle rebound and capture is also discussed, as is the hydrodynamic removal of captured particles. The removal of particles occurs when the applied hydrodynamic removal force overcomes the adhesion force. The effect of adhesion-induced deformation on the removal of particles is introduced and discussed.     

Natural convection mass transfer at conical surfaces

Rates of natural convection mass transfer were determined at vertical cones by measuring the limiting current of the cathodic deposition of copper from acidified copper sulphate solution. Variables studied were cone position (upward or downward apex), apex angle of the cone and copper sulphate concentration. For vertical cones with upward pointing apex the data were represented in the range 4.9×10¹⁰<(Sc Gr)<9×10¹¹ by the equation: $$Sh = 0.128 (Sc Gr)^{0.33}$$ For vertical cones with downward pointing apex the data fit the equation: $$Sh = 0.877 (Sc Gr)^{0.25}$$      

Design of a Commercial Hybrid VTOL UAV System

For the last four decades Unmanned Air Vehicles (UAVs) have been extensively used for military operations that include tracking, surveillance, active engagement with weapons and airborne data acquisition. UAVs are also in demand commercially due to their advantages in comparison to manned vehicles. These advantages include lower manufacturing and operating costs, flexibility in configuration depending on customer request and not risking the pilot on demanding missions. Even though civilian UAVs currently constitute 3 % of the UAV market, it is estimated that their numbers will reach up to 10 % of the UAV market within the next 5 years. Most of the civilian UAV applications require UAVs that are capable of doing a wide range of different and complementary operations within a composite mission. These operations include taking off and landing from limited runway space, while traversing the operation region in considerable cruise speed for mobile tracking applications. This is in addition to being able traverse in low cruise speeds or being able to hover for stationary measurement and tracking. All of these complementary and but different operational capabilities point to a hybrid unmanned vehicle concept, namely the Vertical Take-Off and Landing (VTOL) UAVs. In addition, the desired UAV system needs to be cost-efficient while providing easy payload conversion for different civilian applications. In this paper, we review the preliminary design process of such a capable civilian UAV system, namely the TURAC VTOL UAV. TURAC UAV is aimed to have both vertical take-off and landing and Conventional Take-off and Landing (CTOL) capability. TURAC interchangeable payload pod and detachable wing (with potential different size variants) provides capability to perform different mission types, including long endurance and high cruise speed operations. In addition, the TURAC concept is to have two different variants. The TURAC A variant is an eco-friendly and low-noise fully electrical platform which includes 2 tilt electric motors in the front, and a fixed electric motor and ducted fan in the rear, where as the TURAC B variant is envisioned to use high energy density fuel cells for extended hovering time. In this paper, we provide the TURAC UAV’s iterative design and trade-off studies which also include detailed aerodynamic and structural configuration analysis. For the aerodynamic analysis, an in-house software including graphical user interface has been developed to calculate the aerodynamic forces and moments by using the Vortex Lattice Method (VLM). Computational Fluid Dynamics (CFD) studies are performed to determine the aerodynamic effects for various configurations For structural analysis, a Finite Element Model (FEM) of the TURAC has been prepared and its modal analysis is carried out. Maximum displacements and maximal principal stresses are calculated and used for streamlining a weight efficient fuselage design. Prototypes have been built to show success of the design at both hover and forward flight regime. In this paper, we also provide the flight management and autopilot architecture of the TURAC. The testing of the controller performance has been initiated with the prototype of TURAC. Current work focuses on the building of the full fight test prototype of the TURAC UAV and aerodynamic modeling of the transition flight.