淀粉-MMA接枝共聚物的半干法合成新工艺

以硝酸铈铵(CAN)为引发剂,采用固相半干法合成了玉米淀粉(CS)接枝甲基丙烯酸甲酯(MMA)共聚物。考察了含水量、反应体系的酸性、反应时间与温度、MMA单体和引发剂CAN用量等因素对接枝共聚反应的影响。结果表明,体系含水质量分数为35%左右,CAN用量为CS质量的1.5%～3%,反应温度在40～50℃,反应时间为0.5h左右,可得到接枝率、接枝效率和单体转化率均较高的接枝共聚物。     

三元乙丙橡胶－甲基丙烯酸甲酯溶胀机械接枝共聚研究

采用直接溶胀法，在叶片混合器中以不同条件制备了三元乙丙橡胶－甲基丙烯酸甲酯接枝共聚物。通过动态力学粘弹谱表征，该接枝共聚物具有稳定的双相体系相态。在适宜条件下，可以制得较好综合性能的接枝共聚物。     

化学接枝法制备腻子型吸水膨胀橡胶研究

吸水膨胀橡胶是一种新型的功能高分子材料,过去多用机械共混的方法制备,但是这种方法存在着反复使用性能差的缺点,针对这个问题,本实验采用过硫酸铵/硫代硫酸钠氧化还原引发体系,有效地使丙烯酸钠单体与天然胶乳接枝共聚,制备出吸水倍率相当高的腻子型吸水膨胀天然橡胶。实验结果表明:反应温度、引发剂用量对吸水倍率和接枝率有明显的影响,单体用量对吸水倍率影响较大;反复吸水能力基本保持不变。     

马来酸酐熔融接枝LDPE的性能

采用熔融接枝法制备了低密度聚乙烯(LDPE)与马来酸酐(MAH)接枝物,通过调整反应物的用量及反应条件控制接枝率。随着MAH及引发剂用量的增加,接枝率呈先增大后降低的趋势。低剪切速率时,接枝物的最大初始剪切黏度达4750 Pa·s,远高于纯LDPE;高剪切速率时,接枝物的剪切黏度与纯LDPE趋于相同,约500 Pa·s。接枝物的拉伸强度在8 MPa左右,同纯LDPE接近,断裂伸长率略有下降。     

Graft copolymerization of styrene and acrylonitrile onto EPDM

Acrylonitrile–EPDM–styrene (AES) graft copolymers were synthesized by solution graft polymerization of styrene (St) and acrylonitrile (AN) onto EPDM in an n‐hexane/benzene solvent with benzoyl peroxide (BPO) as an initiator. The structure changes were studied by an FTIR spectrophotometer. The grafting parameters were calculated gravimetrically. The influence of the polymerization conditions, such as the reaction time, concentration of the initiator, EPDM content, and weight ratio of St/AN, on the structure of the products was investigated. It was found that a proper initiator concentration and EPDM content will give a high grafting ratio of the AES resin. The thermal property of the copolymer was studied using programmed thermogravimetric analysis (TGA). The results showed that the copolymer has a better heat‐resistant property than that of ABS, especially for the initial decomposition temperature (T_in) and the maximum weight loss rate temperature (T_max). Also, the mechanism of the graft reaction was discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 428–432, 2002     

改性低毒氯丁橡胶胶粘剂的研究

氯丁橡胶(CR)在有机过氧化物引发下,与低碳数烯类改性单体接枝聚合,采用改性丙酮与低碳芳烃、酯类为低毒混合溶剂制得具有对难粘材料良好粘接的性能且胶液毒性较低的改性低毒氯丁像胶胶粘剂。确定最佳合成的反应温度80℃、反应时间5 h、引发剂的用量0.5%、改性单体的用量10%,投料的方式采用轮流滴加法。     

纤维素醋酸酯接枝己内酯的聚合研究

以冰醋酸为溶剂,浓硫酸为催化剂,将取代度为2 4的二醋酸纤维素水解为取代度为1 4的醋酸纤维素(CA)。以此醋酸纤维素为接枝骨架,ε 己内酯(ε CL)为接枝单体,在辛酸亚锡的引发下,合成了醋酸纤维素/聚己内酯接枝共聚物(CA g PCL)。研究了反应物纯度、原料配比、引发剂与单体摩尔比、反应时间、反应温度对单体转化率(C%)、接枝率(G%)、接枝效率(GE%)的影响。结果表明,当反应温度为140℃,单体ε 己内酯与醋酸纤维素的质量比为4∶1,引发剂辛酸亚锡与单体ε 己内酯的摩尔比为0 005,反应时间为16h,C%,GE%和G%分别为46 8%,65 2%和122 1%。     

Analysis of mechanical,thermal, and morphological behavior of polycaprolactone/wood flour blends

In the present study, the properties of polycaprolactone (PCL) and wood flour (WF) blends were examined by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), Instron mechanical tester, and scanning electron microscopy (SEM). As for results, the mechanical properties of PCL were lowered obviously, due to the poor compatibility between the two phases, when it was blended with wood flours. A fine dispersion and homogeneity of wood flour in the polymer matrix could be obtained when the acrylic acid grafted PCL (PCL‐g‐AA) was used to replace PCL for manufacture of blends. This better dispersion is due to the formation of branched and crosslinked macromolecules since the PCL‐g‐AA copolymer had carboxyl groups to react with the hydroxyls. This is reflected in the mechanical and thermal properties of the blends. In comparison with pure PCL/WF blend, the increase in tensile strength at break was remarkable for PCL‐g‐AA/WF blend. The PCL‐g‐AA/WF blends are more easily processed than the PCL/WF ones since the former had lower melt viscosity than the latter. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1000–1006, 2004     

Preparation and characterization of eugenol‐grafted chitosan hydrogels and their antioxidant activities

The hydrogels composed of chitosan and eugenol were prepared to enhance and sustain antioxidant activities. The vinyl groups of eugenol monomer were directly grafted on the amino groups of chitosan, using ceric ammonium nitrate. The graft of eugenol onto chitosan was confirmed by using Fourier‐transform infrared and proton nuclear magnetic resonance spectroscopies. Results from the swelling behavior, thermal stability, and wide‐angle X‐ray diffraction revealed that the equilibrium water content decreased with increase of graft yields, because of the hydrophobicity of eugenol, although the introduction of eugenol as a side chain disturbed the ordered arrangement of chitosan's crystalline structure. The eugenol‐grafted chitosan hydrogels showed lower pH sensitivity in comparison with chitosan alone, because the amino groups, which were pH sensitive, of chitosan were grafted with eugenol. The scavenging activity of the tested hydrogels increased with graft yield of eugenol, because phenolic groups in the eugenol could play a major role as potent free‐radical terminators, in the results of improved antioxidant activity in eugenol‐grafted chitosan hydrogel in comparison with chitosan alone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3500–3506, 2006     

力化学法制备金属－NR硫化粘合用CSM－NR接枝聚合物

用开炼机，通过力化学方法，将ＮＲ／ＣＳＭ（质量比为１０／９０）制成４５￣＃钢－ＮＲ硫化粘合剂用接枝聚合物。当橡胶本体１００％破坏时，１８０°剥离强度为２３．６～２４．６ｋＮ／ｍ。