从高温合金电溶液中回收铼酸铵的工业试验

采用移动密实床离子交换柱吸附—固定床离子交换柱解吸—蒸发冷却结晶等工序进行高温合金电溶液中铼的高效回收工业试验。结果表明,采用移动密实床交换柱吸附—固定床离子交换柱解吸和再生,可使整个离子交换系统连续运行;采用15BVs 8%NH4SCN溶液解吸铼时,可使流出液含铼浓度降至1mg/L;采用20BVs 2mol/L H2SO4溶液使树脂再生时,再生树脂对铼吸附率仍可达99.97%,且吸附后液含铼浓度可降至0.4mg/L;采用6倍理论用量CaCl2沉钼时,钼沉淀率为99.69%;最终所得铼酸铵产品纯度达到99.99%。     

甘肃甘南野生羊肚菌液体发酵生长动力学研究

以甘肃甘南地区野生羊肚菌（Morchella esculenta）为研究对象,运用遗传算法进行了羊肚菌M. esculenta液体菌种发酵动力学参数估计,通过对不同初始串集的多次实验,各动力学参数估计收敛值结果基本一致。此外,运用Monod模型、Logistic模型以及1stOpt（FirstOptimization）软件对羊肚菌M.esculenta生长过程进行了拟合,通过对方程模拟结果的误差分析、相关性分析、中位数检验以及数据分布检验最终选择 Logistic 模型和1stOpt拟合模型作为此次实验羊肚菌M.esculenta液体菌种深层发酵生长动力学模型。     

基于AU6842芯片的家用音响USB数字音频模块的设计

AU6842芯片是一款数字音频soc芯片,其中集成了USB主机控制器,可以用单芯片实现USB数字音频模块.利用该芯片设计的USB数字音频模块通过标准串行口同音响主控制器通信,处理音响主控制器发出的操作命令,实现从USB存储设备中读取并播放MP3文件.本文将介绍USB数字音频模块的结构和各个子模块的功能:针对USB音频模块功能分析AU6842各个功能模块的技术参数,提供USB音频模块的硬件电路设计;描述该模块控制软件的通信协议和模 块的工作状态.     

多板组合焊接型法兰吊盖结构设计与有限元分析

法兰吊盖广泛应用于石油化工行业设备的吊装工程中,传统大吨级吊盖设计多采用单吊耳板单法兰盲板型结构,并采用整体锻造加工工艺成型,其制作成本高昂。以加氢精制反应器吊盖结构设计为例,设计了一种制作成本较低的多板组合焊接型法兰吊盖结构;同时针对解析计算难以对该型吊盖结构进行精确应力分析的问题,利用有限元法从设备起吊到直立的全过程对吊盖结构进行了受力分析,对连接销轴按照接触问题进行了非线性计算。计算结果和工程实践表明该型吊盖结构强度可靠,为项目后续设备吊盖设计提供了依据,大幅度地节省了项目成本。该实例对类似吊盖结构设计与强度校核具有借鉴意义。     

双CMOS图像传感器的抗晕光图像采集系统设计

为解决CMOS图像传感器采集图像时产生晕光问题,提出一种CMOS图像传感器的抗晕光图像采集系统设计方案.TMS320C6414采用阈值化分割算法,对两路图像数据进行剪裁,汲取各自图像的优点,输出一路比较清晰的图像信息.其效果相当于扩大了CMOS图像传感器的动态范围,从而达到抗晕光的效果.     

A multi-mode multi-band RF receiver front-end for a TD-SCDMA/LTE/LTE-advanced in 0.18-μm CMOS process

正A fully integrated multi-mode multi-band directed-conversion radio frequency(RF) receiver front-end for a TD-SCDMA/LTE/LTE-advanced is presented.The front-end employs direct-conversion design,and consists of two differential tunable low noise amplifiers(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The two independent tunable LNAs are used to cover all the four frequency bands,achieving sufficient low noise and high gain performance with low power consumption.Switched capacitor arrays perform a resonant frequency point calibration for the LNAs.The two LNAs are combined at the driver stage of the mixer,which employs a folded double balanced Gilbert structure,and utilizes PMOS transistors as local oscillator(LO) switches to reduce flicker noise.The front-end has three gain modes to obtain a higher dynamic range.Frequency band selection and mode of configuration is realized by an on-chip serial peripheral interface(SPI) module.The frontend is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.3 mm~2.The measured doublesideband (DSB) noise figure is below 3.5 dB and the conversion gain is over 43 dB at all of the frequency bands. The total current consumption is 31 mA from a 1.8-V supply.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

关于沉降控制复合桩基在工程中的应用

随着我国经济的快速发展,各个行业都快速的扩张着,而作为基础行业的建筑业也不可避免的快速发展中,并且由于现在各个企业都把自己的利润率和企业的经济效益放在了首位,这就促进了很多新型的技术的发展,也出现了很多的新方法。本文主要介绍了沉降控制复合桩基是什么,并进一步探讨了其在工程中的应用优势。     

浅析焦炭反应性与高炉冶炼

总结了焦炭反应性与高炉冶炼关系的认知历程,阐述了不同反应性焦炭对高炉冶炼过程的影响以及不同反应性焦炭生产的技术手段和研究现状。通过对不同反应性焦炭与高炉冶炼过程适用性的讨论,提出了应根据高炉的冶炼条件和矿石的还原性能来规定适宜的焦炭反应性。     

金属锂负极改性研究现状

综述了金属锂二次电池中金属锂负极改性的研究进展。主要介绍了电解液添加剂、金属锂保护膜、新形态锂电极等主要改性方法,并对以后锂电极的发展趋势进行了展望。