Synergistic effect of bulk phase doping and layered-spinel structure formation on improving electrochemical performance of Li-Rich cathode material

In this study, La was doped into the lithium layer of Li-rich cathode material and formed a layered-spinel hetero-structure. The morphology, crystal structure, element valence and kinetics of lithium ion migration were studied by field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). The La doped lithium-rich cathode material exhibited similar initial discharge capacity of 262.8 mAh g^?1 at 0.1 C compared with the undoped material, but the discharge capacity retention rate can be obviously improved to 90% after 50 cycles at 1.0 C. Besides that, much better rate capability and Li⁺ diffusion coefficient were observed. The results revealed that La doping not only stabilized the material structure and reduced the Li/Ni mixing degree, but also induced the generation of spinel phase to provide three-dimensional diffusion channels for lithium ion migration. Moreover, the porous structure of the doped samples also contributed to the remarkable excellent electrochemical performance. All of these factors combined to significantly improve the electrochemical performance of the material.     

Improved electrochemical performance of silicon-carbon anodes by different conductive agents

Journal of Materials Science: Materials in Electronics - Silica/silicon/polyacrylonitrile (SiO2/Si/PAN) composites were prepared as active anode for lithium-ion batteries (LIBs) using a rational...     

基于有限元仿真的发泡硅橡胶老化规律研究

通过力学性能测试得到发泡硅橡胶应力应变曲线,结合Ogden(Foam) 3阶超弹本构模型,建立发泡硅橡胶静密封系统的有限元仿真模型,得到大压缩量下发泡硅橡胶的von Mises应力及接触压力分布情况。仿真结果表明:大压缩量下发泡硅橡胶对称中心线位置的von Mises应力、接触压力值较大,在橡胶边缘和靠近限位环处接触应力数值有突增。开展140℃热空气老化试验,测定老化后发泡硅橡胶应力应变曲线,结合有限元仿真模型分析发泡硅橡胶老化后von Mises应力、接触压力的变化规律。结果表明:经过热空气老化后,在一定载荷下发泡硅橡胶等效应力和接触压力均呈增大的趋势。     

A Dual Inhibitor of DYRK1A and GSK3β for β-Cell Proliferation: Aminopyrazine Derivative GNF4877

Loss of β-cell mass and function can lead to insufficient insulin levels and ultimately to hyperglycemia and diabetes mellitus. The mainstream treatment approach involves regulation of insulin levels; however, approaches intended to increase β-cell mass are less developed. Promoting β-cell proliferation with low-molecular-weight inhibitors of dual-specificity tyrosine-regulated kinase 1A (DYRK1A) offers the potential to treat diabetes with oral therapies by restoring β-cell mass, insulin content and glycemic control. GNF4877, a potent dual inhibitor of DYRK1A and glycogen synthase kinase 3β (GSK3β) was previously reported to induce primary human β-cell proliferation in vitro and in vivo. Herein, we describe the lead optimization that lead to the identification of GNF4877 from an aminopyrazine hit identified in a phenotypic high-throughput screening campaign measuring β-cell proliferation.     

方腔内耦合传热传质非对称流动数值模拟

对带有质热源的方腔内流体传热传质进行数值研究。针对不同Ra、Nc、Sr和Df，探究对称方腔内流体传热传质的分岔特性。结果表明：存在临界Ra_c使流体流动形态发生转变，当Ra<Ra_c时，流体流线、温度场和浓度场对称分布；当Ra>Ra_c时，流体发生偏斜。增大浮升力，流体更易发生分岔现象。增强Soret和Dufour效应可增强传热对称性并增大流体发生分岔的临界Rayleigh数。     

汽车悬架球头拉杆冷成形技术

为提高生产效率、改变原来通过车削加工汽车悬架球头拉杆的方式,提出了一种球头拉杆的多工位冷镦成形工艺。基于DEFORM-3D软件建立了有限元模型,对球头拉杆的塑性成形过程进行了仿真,研究了预成形凸模入模角α、预成形凹模圆角R1、终成形凹模圆角R2以及终成形凹模入模角β等工艺参数对球头拉杆成形的影响,并进行了正交试验,以模具在球头拉杆成形过程中所受载荷及工件损伤值为优化目标,获得了合理的工艺参数组合。结果表明:在保证工件成形质量及模具寿命的前提下,当预成形凸模入模角α为30°、预成形凹模圆角R1为12 mm、终成形凹模圆角R2为3 mm、终成形凹模入模角β为60°时,模具载荷及工件损伤有显著的降低。采用优化后的参数进行试模生产,工件成形质量较好,验证了模拟结果的可信性,能够有效地指导工艺设计人员的设计工作。     

基于模糊分析法的合肥市水资源承载力评价

以合肥市为例,选取人均水资源量、年产水模数、人均供水量、植被覆盖率、日生活用水量、万元GDP用水量、万元工业增加值需水量、人口密度、城市化率、农田灌溉定额、水资源开发利用率、人均GDP、污水排放达标率、水功能区达标率、生态用水率15个指标,在建立合肥市水资源承载力评价指标体系及等级标准体系的基础上,构建模糊分析模型并借助Matlab工具计算隶属度、确定指标权重,进而计算2013~2017年水资源承载等级,获得了合肥市水资源承载力情况,计算结果对合肥市水资源开发利用具有一定的参考意义。     

Study on wax precipitation characteristics of wax deposit in pipes

Wax deposit properties are a significant concern in pipeline pigging during waxy crude oil transportation. In the present work, the impacts of flow conditions and oil properties on the wax precipitation characteristics of wax deposits are investigated. A flow loop apparatus was developed to conduct wax deposition experiments using four crude oils collected from different field pipes. The differential scanning calorimetry (DSC) technique was employed to observe the wax precipitation characteristics of crude oil and wax deposit. The results show that the wax content and the wax appearance temperature (WAT) of the deposits increase with shear stress and radial temperature gradient, and decrease with radial wax molecule concentration gradient near the pipe wall. The DSC tests on the wax deposits revealed that the deposit wax content is strongly correlated to the oil wax content. Furthermore, an empirical correlation was developed to predict the wax content and the WAT of the wax deposit. Verification of the empirical correlation using the different oils indicated that the average relative error of the wax content prediction and average absolute error of WAT prediction were 13.2% and 3.6°C, respectively.     

In-situ preparation of cross-linked hybrid anion exchange membrane of quaternized poly (styrene-b-isobutylene-b-styrene) covalently bonded with graphene

Introducing graphene into polymer matrix is an effective way to enhance performances of anion exchange membrane (AEM). However, utilizing the advantages of graphene by physical approach is limited due to the weak interface interaction between graphene and polymer matrix. Herein, we report an effective strategy to covalently bond graphene with polymer matrix to improve the interface interaction and further to improve the properties of AEM. A series of cross-linked quaternized graphene-based hybrid AEM were fabricated by covalently bonding poly (vinylbenzyl chloride) grafted graphene (GN-g-PVBC) copolymer with chloromethyl functionalized poly (styrene-b-isobutylene-b-styrene) (SIBS) through the cross-linker (N,N,N′,N′-tetramethyl-1,6-hexanediamine) by in-situ synthetic approach. The interface interaction between graphene and QSIBS is greatly enhanced according to micromorphology characterization of the hybrid membrane. The cross-linked quaternized hybrid AEM containing 0.55 wt% of GN-g-PVBC exhibits obviously improved dynamical mechanical properties (storage modulus: 418 MPa), ion conductivity (1.81 × 10² S cm^?1), methanol barrier property (5.19 × 10^?7 cm² s^?1), selectivity (3.49 × 10⁴ S s cm^?3) at 60 °C and especially a comparably excellent chemical stability to that of Nafion 115 due to the enhanced interface interaction between graphene and the polymer matrix.