һ���꾮Һ�ð����󻬼�HML���о�

钻井液润滑剂是一种重要的钻井液化学处理剂，它的作用是改善钻井液润滑性，降低井壁与钻具（或套管）之间的磨擦，降低钻柱旋转扭矩和起下钻阻力，从而减少卡钻事故的发生。文章根据目前使用的白油钻井液润滑剂存在的不足，提出研制一种新型白油钻井液润滑剂。通过正交实验优选了润滑剂配方。经室内实验和现场实验证明该产品润滑性能好，与钻井液配伍性好，无毒性对环境影响小。     

椭圆型偏微分方程的加法Schwarz方法

1.引 言 古典加法Schwarz方法(ASM)对于一般问题收敛很慢,在大多数情况下, ASM只能作为预条件子.另一方面,ASM的并行性能非常好,尤其适合大规模粗粒度并行计算,近年来随着并行机系统及并行计算的兴起,ASM重新受到重视.许多学者研究了怎样提高ASM的收敛速度[1,2,4].他们发现加法Schwarz方法之所以收敛慢是由于在内边界上采用     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

我国先进制造技术的现状和发展途径

介绍了现在制造业中面临的问题，通过对问题的分析，提出了发展先进制造前沿技术的见解和在我国发展先进制造技术的途径，同时展望了先进制造技术的发展前景。     

介绍两种画中画插入播出器

介绍画中画插入播出器的工作原理及设计思想，并给出了实际的电原理图。     

激光辐照制备搪瓷涂层

激光辐照制备的搪瓷涂层表面粗糙,与金属基材结合牢固。一般由 Si,Al,Na,K,B,F,O等元素组成。在激光辐照过程中 K,Na 明显地挥发,从而在涂层中的含量明显减少;Co,Ni,主要分布在界面附近;Fe 元素也由基材进入涂层,呈梯度状分布,在界面过渡区含量很高,在涂层内含量很低。搪瓷涂层的形成与激光辐照参数,特别与激光功率间存在极为密切的关系;只有选用合理的参数,才能制得搪瓷涂层。     

Industrialization of High Performance Sintered NdFeB Magnets

Sintered Nd-Fe-B magnet was manufactured by advanced equipment via a SC (Strip casting) technology.It has integrative performance.     

Synthesis of chemically and structurally modified dicalcium silicate

This paper describes the synthesis of cements, chemically and structurally related to Ca₂SiO₄. Silica was obtained from rice hull after heating at 600 °C. Calcium oxide and small amounts of barium chloride were mixed in order to obtain a final (Ca/Si) or (Ca+Ba)/Si ratio equal to 1.95, 1.90, and 1.80, which is lower than in the conventional cement. The solids were mixed and ultrasonically treated for 1 h with a water/solid ratio of about 20. After drying and grinding, the mixtures were heated up to 1100 °C. It was possible, in some cases, to obtain a cementitious material. These cements are structurally related to β-Ca₂SiO₄ and the lower (Ca+Ba)/Si ratio obtained was 1.95. The initial chemical compositions of these cements are: (Ca_1.83+Ba_0.12)SiO₄ and (Ca_1.79+Ba_0.16)SiO₄. A further lowering in the (Ca+Ba)/Si ratio changes the nature of the silicates.     

聚合反应器制造质量控制要点探讨

聚合反应器是无法检修设备,不允许打开,所以聚合反应器的制造质量必须严格控制,在设备制造过程中,严格按照设计图纸、技术要求及国家现行标准,进行控制设备制造、检验和验收,使制造质量达到规定要求。     

五轴铣削加工中心坐标转换数学模型的建立及应用

首先以 HERMLE C1200 U 为例分析了五轴铣削加工中心的基本结构,然后据此给出了涉及多轴铣削加工中心后置处理角度分配和坐标变换的数学模型,最后介绍了以此数学模型为核心,为UG 软件开发的后置处理软件 UG-HERP1.0的解决方案。