LED生产过程中的质量控制

对LED封装过程可能出现的问题逐一指出，并提出解决的办法，着重介绍封装位置对LED发光亮度的影响。以期引起LED封装管理人员及工作人员的注意。     

固定电子分立元器件用胶粘剂E—4X的研制

介绍了一种不同于灌封材料，具有触变性，粘接性能优良，使用方便的固定电子分立元器件用胶粘剂Ｅ－４Ｘ。与国外同类产品Ｅｐ－４３３ｘ胶粘剂对比，其综合性能优于Ｅｐ－４３３胶粘剂。     

基于画圆算法的简单弧形贴图算法

本文提出了一种基于画圆算法的简单弧形贴图算法，并分析了该算法的可行性。     

RETARDATION AND REPAIR OF FATIGUE CRACKS BY ADHESIVE INFILTRATION

Abstract— This paper presents results which demonstrate that polymeric filler materials, such as low-viscosity epoxies, can be vacuum-infiltrated into fatigue cracks in 7050 aluminium alloy to produce significant levels of fatigue crack retardation. It was found that the main test variable affecting the degree of retardation was the stress level at which the adhesive was introduced and cured. Two infiltrated adhesives were tested.
Infiltration at 0% (of the original) peak fatigue stress level produced negligible retardation, while infiltration at the 80% stress level produced about 300% increase in fatigue life for one adhesive and 3000% for the other adhesive. For the highest infiltration stress level both crack-face wedging and adhesion contributed initially to the retardation, but the adhesive component ceased after a crack grew through the adhesive to the original crack tip position. The results are discussed in terms of the applicability of the technique to highly-stressed aircraft components.     

自粘聚合物改性沥青防水卷材胶粘剂

在SBS改性沥青防水卷材表面涂敷一层自粘性胶粘剂并以隔离纸覆盖，使用时撕掉隔离纸直接粘贴于屋面即可粘接密封牢，不但施工方便而且消除了熔融法施工造成的污染。该胶粘剂由沥青40％～65％，SBS 5％～30％，增粘剂2％～25％和助剂5％～25％构成。胶层具有可塑性、延展性，可自行填补屋面出现的裂缝，保证防水卷材的防水密封效果。     

Numerical Analysis of the Constrained Blister Test

The constrained blister test is investigated through finite element analysis to determine the applicabilities and the limitations of the new technique. Numerical results confirm that the strain energy release rate asymptotically approaches a constant value. These results also show that the test technique and the approximate solution for strain energy release rate are applicable for some practical cases.     

氯丁橡胶胶粘剂

1低温聚合、快速结晶型氯了用胶氯丁橡胶的结晶度与反式1，4含量有关，而反式1，4含量又是由乳液聚合温度决定的，聚合温度越低，反式1，4含量越高。为了得到快速结晶型氯丁橡胶，聚合必须在较低温度下进行，一般不高于15℃。快速结晶型氯丁橡胶广泛用于鞋底的粘接、层压板的粘合、汽车装饰，以及其它多种用途。主要从引发剂、调节剂等几个方面改进氯丁橡胶的性能：2＠基氯T橡胶。驻基氯丁胶是氯丁二烯和甲基丙烯酸的共聚物，是非结晶性，适用于室温硫化和耐热性用途。与快结晶型氯丁橡胶相比，由其配制的胶粘剂粘结强度形成更快，耐热性增…     

Measurement of Adhesive Bond Properties Including Damage by Dynamic Mechanical Thermal Analysis of a Beam Specimen

A method to obtain mechanical properties using a bonded (double) cantilever beam (or three point bend) specimen loaded in a manner to produce pure shear in the adhesive layer is reviewed. A revised mathematical solution which allows for easier interpretation of optimum beam dimensions to the one originally developed by Moussiaux, Cardon and Brinson for the static case is presented. An extension of this solution for a fixed/fixed viscoelastic beam under steady state oscillations developed by Li, Dickie and Morman is also discussed. Previous results using a vibrating beam to determine the complex viscoelastic properties of a bonded beam are reviewed. These results demonstrate conclusively that dynamic mechanical thermal analysis (DMTA) measurements discriminate differences in surface treatments and various environmental conditions. New measurements are presented that indicate the DMTA procedure can be used to quantify damage simulated by imbedded flaws in beams. The procedure is also shown to assess the effects of both humidity and corrosive environments on lap specimens. It is suggested that this technique may ultimately provide a method to quantify the amount of hidden damage in an adhesive joint subjected to fatigue, moisture or corrosive environments.     

XK908耐高温蒸煮胶粘剂的研制与应用

叙述了ＸＫ９０８耐高温蒸煮胶粘剂的制备方法，主要反应条件对缩聚反应和扩链反应的影响，并对产品的应用效果与国外同类产品进行了比较     

Motion-based method for estimating time required to attach self-adhesive insulators

A self-adhesive insulator is a component of a home appliance that is used to suppress vibration or prevent humidity affecting the internal parts of the appliance. There is a wide range of types and designs available, allowing them to be applied to areas having different shapes. At the design stage, once an insulator design has been developed sufficiently to identify its dimensions and features, the attaching time and baseline cost must be estimated with reasonable accuracy to enable a comparison of vendor quotes. However, the current estimation method is not sufficiently accurate in terms of the baseline cost. This paper presents a motion-based time-estimating scheme with which the time required for the attachment of such insulators can be calculated more accurately. The scheme has been developed by analyzing the motions needed to attach 350 insulators and then designating representative motions and their time values. For this purpose, a modular arrangement of predetermined time standards (MODAPTS) is adopted. Motion-based time-estimation method is useful in terms of simplicity and accuracy. It enables design engineers to estimate the time required for the attachment based only on a drawing of the insulator and a few MODAPTS rules. Estimates made with this method should vary from the actual value by no more than 9.5%.