Damping oscillations in a wire bending process

This paper presents an approach to modify CAD/CAM generated motion profiles for wire bending machines, in order to damp wire oscillations without decreasing machine throughput. Two different methodologies are presented, both leveraging on a simple and easily identifiable model of wire oscillations, the first one based on a filtering approach, the second one on an optimisation approach. The two methodologies are both characterised by a low computational complexity, allowing them to be integrated directly in the bending machine user interface, and can rely on a standard camera to identify wire oscillation parameters. A thorough experimental validation of the approaches is also presented, showing promising results in damping oscillations with wires of different materials.     

Effect of PyC interface phase on the cyclic ablation resistance and flexural properties of two-dimensional Cf/HfC composites

Composites based on hafnium carbide and reinforced with continuous naked carbon fiber with and without PyC interface were prepared at low temperature by precursor infiltration and pyrolysis and chemical vapor deposition method. The microstructure, mechanical property, cyclic ablation and fiber bundle push-in tests of the composites were investigated. The results show that after three times ablation cycles, the bending strength of samples without PyC interface decreased by 63.6 %; the bending strength of samples with PyC interface only decreased by 37.8 %. The force displacement curve of the samples with PyC interface presented a well pseudoplastic deformation state. The mechanical behavior difference of two kinds of composites was due to crucial function of PyC interface phase including protection of fiber and weakening of fiber/matrix interface.     

高性能纤维的单纤维压缩弯曲性能

选取11种高性能纤维,包括PBO纤维、芳纶1313纤维、对位芳纶纤维、高强聚乙烯长丝和高强聚乙烯短纤等,采用单纤维压缩弯曲仪测试纤维的单纤维压缩弯曲性能,并对其压缩弯曲曲线进行对比分析。结果表明,11种高性能纤维中,Technora纤维的最大力和抗弯刚度最大,在相同条件下,Technora纤维更难被压弯;PBO纤维普通丝的抗弯刚度远大于高模量丝的抗弯刚度;直径相同的条件下,芳纶1414纤维的最大力、等效弯曲模量及抗弯刚度明显高于芳纶1313纤维;超高分子量聚乙烯纤维的压缩弯曲曲线变化趋势最明显。     

AZ31镁合金薄板经不同累积应变的连续弯曲变形后的显微组织与成形性能

对AZ31镁合金板材进行不同累积应变的连续弯曲变形及退火处理,随后对显微组织与力学性能的变化进行了研究。结果表明:经不同累积应变的连续弯曲变形后,镁合金板材的显微组织中没有发现孪晶,退火后,板材表层的晶粒异常长大,粗晶层的厚度随着累积应变的增加而增加,并且镁合金板材的织构朝RD方向偏转,偏转角度随累积应变的增加而增大;与原始板材相比,连续弯曲变形及退火处理使镁合金板材呈现出较好的室温成形性能(杯突值由2.3 mm提高到4.9 mm,提高了~113%),这主要归因于基面织构的改善使镁合金板材的r值减小与n值增大。     

The fabrication and mechanical properties of SiC/SiC composites prepared by SLS combined with PIP

Traditionally, SiC components with complex shapes are very difficult or even impossible to fabricate. This paper aims to develop a new manufacturing process, combining selective laser sintering (SLS), cold isostatic pressing (CIP) and polymer infiltration pyrolysis (PIP), to manufacture complex silicon carbide parts and improve the mechanical properties of silicon carbide ceramic parts. The density and porosity of SiC/SiC composites were measured. Furthermore, the mechanical properties of the specimens with cold isostatic pressing and the specimens without cold isostatic pressing were compared. The bending strength of the specimens with cold isostatic pressing was 201?MPa, and the elastic modulus was 1.27?GPa. And, the bending strength of the specimens without cold isostatic pressing was 142?MPa, and the elastic modulus was 0.88?GPa. Increasing the density of SiC/SiC can enhance the mechanical properties of SiC/SiC composites.     

A comprehensive study on the size-dependent hygrothermal analysis of exponentially graded microplates on elastic foundations

Abstract

In this paper, the effects of hygrothermal conditions on various behaviors, such as bending, free vibration, mechanical and thermal buckling, of exponentially graded microplates lying on two-parameter elastic foundations are investigated. The trigonometric four-variable plate theory incorporated to the modified couple stress theory (MCST) is employed to derive the equations of motion. The present MCST contains an internal material length scale parameter, thus it can capture the size effect. The microplate is assumed to be subjected to a temperature rise and moisture concentration which are varied linearly through the thickness of the plate. Based on an exponential law, the material properties of the microplate are graded only in z direction. The equations of motion are solved analytically to obtain the displacements, stresses, eigenfrequencies and critical buckling load and temperature of the microplates. The present results are validated by comparing them with those previously published. The numerical examples reveal that considering the size effect and/or the elastic foundations leads to an increment in plate stiffness and thereby leads to a decrement in the deflection and an increment in eigenfrequency and buckling loads. It is also shown that the size effect is negligible for the thicker plate.     

Injection molding,debinding and sintering of ZrO2 ceramic modified by silane couping agent

In this paper, Injection molding, debinding and sintering of ZrO₂ ceramic modified by silane coupling agent (A151) were studied by measuring the melt index of feedstocks, the soluble removal ratio of green parts, the bending strength of green and sintered parts, the surface and fractural morphologies of sintered parts. The results showed that the melt index of ZrO₂ feedstocks, the weight removal ratio of soluble binders, and the bending strength of green parts increased after adding A151. When the density of sintered parts was between 5.97–6.03 g/cm³, it was not the main factor influencing the bending strength. However, the bending strengths of sintered parts decreased due to microcrack formation when thermal debinding process was too fast or slow. The interesting phenomenon of the abnormal grain growth with transgranular fracture in the sintered parts obviously occurred above 1550 ℃, which made the effect of sintering temperature on the strength become complex.     

船舶海水管路钛合金应用技术研究

钛合金以其高比强度、优良的耐海水腐蚀性能,成为未来船舶选材的热点。综述了海水管路用钛合金的材料选用、焊接技术、弯管技术、腐蚀防护以及防海生物污损等方面的研究工作进展并进行分析,证明钛合金是船舶海水管路系统的理想选择,以期推动钛合金在船舶海水管路的推广和应用。     

Enhanced bending strength and microwave dielectric properties of Li2MgTi3O8 ceramics by adding Si3N4 reinforcing phase

In the 5G era, the dielectric materials used in microwave electronic components must have not only have good microwave dielectric characteristics but also excellent structural characteristics. Li₂MgTi₃O₈ (LMT) ceramics have excellent microwave dielectric properties; however, their low bending strength limits their further applications in the 5G era. In this work, the dielectric properties and bending strength of LMT ceramics were optimized by the addition of Si₃N₄ reinforcing phase using a solid-phase method, and the effects of Si₃N₄ addition on the sintering properties, microscopic structure, crystalline phase, dielectric properties and bending strength of ceramics were investigated. The X-ray diffraction pattern indicates that all ceramics exhibit spinel structure. Combined with the phenomenon of grain reduction in the SEM graph, it indicates that the addition of Si₃N₄ can inhibit the grain growth and achieve the purpose of fine-grain strengthening. The dispersion enhancement of second phase particles is also one of the reasons for the increase of bending strength. LMT ceramics doped with 0.5 wt% Si₃N₄ exhibited the maximum bending strength after sintering at 1050 °C for 4 h, which was 76.97% higher than that of pure LMT ceramics. In addition, the ceramics exhibited outstanding dielectric properties: a dielectric constant of 23.20, quality factor of 49344 GHz, and temperature coefficient of ?5.90 ppm/°C. The high bending strength and good microwave dielectric properties indicate that Si₃N₄-added LMT ceramics can be effectively applied in the 5G era.     

Additive manufacturing of zirconia ceramics by material jetting

The possibility of additive manufacturing of ceramics has been reported widely in scientific literature. This study investigates the potential of direct inkjet printing or material jetting of 3Y-TZP ceramics by assessing the microstructure and mechanical properties of the sintered printed parts. The technique allows to print in layers of 10.5 μm, with an as-printed green density of 58 % and nearly fully sintered density of 6.03 ± 0.1 g/cm³ (99.7 % TD). The dimensions of the green and sintered parts were highly accurate but showed an anisotropic roughness in function of the building direction, mainly due to the support structures. The biaxial bending and 4-point bending strength of the sintered material was found to be substantially higher in the XY direction than in the building (Z) direction. SEM and X-Ray computed tomography revealed the presence of delamination cracks, agglomerates and spherical pores, which were identified as fracture origins on fractured surfaces.