The effect of synthesis conditions on the phase composition and structure of thorium bearing murataite ceramics

Samples of thorium-bearing ceramic with a target composition (wt%) 5 Al₂O₃, 10 CaO, 55 TiO₂, 10 MnO, 5 Fe₂O₃, 5 ZrO₂, 10 ThO₂ were produced by melting in glassy carbon crucibles in a resistive furnace and by cold crucible inductive melting (CCIM) at a vibration power of 10 kW and operation frequency of 5.28 MHz. All the samples contained 85–95 vol% murataite polytypes with 5- (5C), 8- (8C), and 3-fold (3C) elementary fluorite unit cell composing core, intermediate zone and rim of the grains, respectively, and minor crichtonite, perovskite, pyrochlore, rutile, etc. A feature of the ceramics obtained by melting in glassy carbon crucibles is formation of Fe (II) titanate whereas the inductive-melted ceramics contained traces of vitreous phase due to melt contamination with a cold crucible putty material. Melting rate in the cold crucible of up to 350 kg/(m² × h) has been achieved. The ceramics obtained have excellent chemical durability.     

Activated Carbon Supported CaO from Waste Shells as a Catalyst for Biodiesel Production

In the wake of increasing environmental constraints, this work is aimed at developing a catalyst purely prepared from waste biomass source as the raw material. The catalyst is investigated for its applicability in transesterification of vegetable oil with the objectives: (i) to use waste shells of mollusk as raw material for the preparation of activated carbon and CaO; (ii) to use it as heterogeneous catalyst in the transesterification of waste cooking oil; (iii) to optimize the different parameters affecting the transesterification reaction; and (iv) to study its reusability. Under optimized conditions it was observed that a conversion >90% was possible and the catalyst could be reused five times with a slight loss in activity. This study indicates that the biomass source could also be used as a potential raw material in the synthesis of environmentally benign catalysts.     

Cold crucible melting and characterization of titanate-zirconate pyrochlore as a potential rare earth/actinide waste form

La-Ce-Gd titanate-zirconate pyrochlore-based ceramics was synthesized at the lab-scale inductive melting unit with a 56?mm inner diameter cold crucible. Batch feeding rate and melting ratio were 3?kg/h and 3?kW?h/kg respectively. The ceramics is composed of 85–90?vol% zoned grains of the pyrochlore structure phase, the sample has excellent chemical durability in hot water and may be considered as a promising matrix for actinide – rare earth fraction of high level waste.     

The effect of non-uniform temperature on the sorption-enhanced steam methane reforming in a tubular fixed-bed reactor

The effect of non-uniform temperature on the sorption-enhanced steam methane reforming (SE-SMR) in a tubular fixed-bed reactor with a constant wall temperature of 600 °C is investigated numerically by an experimentally verified unsteady two-dimensional model. The reactor uses Ni/Al₂O₃ as the reforming catalyst and CaO as the sorbent. The reaction of SMR is enhanced by removing the CO₂ through the reaction of CaO + CO₂ → CaCO₃ based on the Le Chatelier's principle. A non-uniform temperature distribution instead of a uniform temperature in the reactor appears due to the rapid endothermic reaction of SMR followed by an exothermic reaction of CO₂ sorption. For a small weight hourly space velocity (WHSV) of 0.67 h^?1 before the CO₂ breakthrough, both a low and a high temperature regions exist simultaneously in the catalyst/sorbent bed, and their sizes are enlarged and the temperature distribution is more non-uniform for a larger tube diameter (D). Both the CH₄ conversion and the H₂ molar fraction are slightly increased with the increase of D. Based on the parameters adopted in this work, the CH₄ conversion, the H₂ and CO molar fractions at D = 60 mm are 84.6%, 94.4%, and 0.63%, respectively. After CO₂ breakthrough, the reaction of SMR dominates, and the reactor performance is remarkably reduced due to low reactor temperature.For a higher value of WHSV (4.03 h^?1) before CO₂ breakthrough, both the reaction times for SMR and CO₂ sorption become much shorter. The size of low temperature region becomes larger, and the high temperature region inside the catalyst/sorbent bed doesn't exist for D ≥ 30 mm. The maximum temperature difference inside the catalyst/sorbent bed is greater than 67 °C. Both the CH₄ conversion and H₂ molar fraction are slightly decreased with the increase of D. However, this phenomenon is qualitatively opposite to that for small WHSV of 0.67 h^?1. The CH₄ conversion and H₂ molar fraction at D = 60 mm are 52.6% and 78.7%, respectively, which are much lower than those for WHSV = 0.67 h^?1.     

熔融制样-X射线荧光光谱法测定硅铁中硅磷锰铝钙铬

熔融制样-X射线荧光光谱法(XRF)测定硅铁合金样品,需重点解决样品前处理中合金样品侵蚀铂-黄坩埚的难题。硅铁样品以四硼酸锂-碳酸锂预氧化剂在石墨垫底瓷坩埚中高温预氧化熔融后,再将熔融物转移至铂-黄坩埚中,用四硼酸锂熔融制成玻璃熔片,实现了熔融制样-X射线荧光光谱法对硅铁合金中硅、磷、锰、铝、钙、铬的测定。实验讨论了预氧化熔融的熔剂体系及氧化方法、试样与熔剂的稀释比,结果表明,试样与熔剂以1∶35的稀释比,以10滴300g/L碘化钾溶液为脱模剂,在1100℃熔融30min,熔融制得的玻璃片均匀、透明、无气泡,符合测定要求。用具有浓度梯度的系列硅铁有证标准样品制作校准曲线,各待测元素校准曲线的线性相关系数均大于0.9995。方法应用于硅铁合金实际样品中硅、磷、锰、铝、钙、铬的测定, 结果的相对标准偏差(RSD,n=11)在0.1%~5.8%之间;正确度试验表明,硅铁标准样品的测定结果与认定值相符,硅铁实际样品的测定结果与国家标准方法测定值一致,能满足常规分析要求。     

Colloidal processing of Al2O3-doped zirconia ceramics with CaO–P2O5–SiO2 glass as additive

Well-dispersed concentrated aqueous suspensions of Al₂O₃-doped Y-TZP (AY-TZP), AY-TZP with 5.4 vol% of CaO–P₂O₅–SiO₂ (CaPSi) glass (AY-TZP5) and 10.5 vol% CaPSi glass (AY-TZP10), with ammonium polyacrylate (NH₄PA) dispersant were prepared to produce slip cast compacts. The rheological properties of 35 and 40 vol% slips were studied. The densification, microstructure as well as hardness and fracture toughness were investigated as a function of CaPSi glass content at 1300°C-1500°C. The optimum NH₄PA concentration of 35 vol% AY-TZP5 and AY-TZP10 slips at pH ~9 was found to be about 43% and 67% greater than that of AY-TZP slips; this behavior was related to the greater amounts of Ca²⁺ ions leached out from the CaPSi glass surface. The viscosity of stabilized 40 vol% slips with NH₄PA attained a minimum value at 5.4 vol% CaPSi glass addition, and resulted in a more dense packing of cast samples. AY-TZP5 can be sintered at a lower temperature (1300°C) compared to that of AY-TZP. AY-TZP5 exhibited a fine microstructure of tetragonal ZrO₂ (grain sizes below 0.3 µm), and ZrSiO₄–Ca₂P₂O₇ particles homogeneously distributed within the zirconia matrix. It presented similar fracture toughness and a slightly lower hardness compared to those of AY-TZP.     

Effect of CaO on the optical quality and microstructure of transparent MgO·1.5Al2O3 spinel ceramics prepared by reactive sintering

Transparent MgO·1.5Al₂O₃ spinel ceramics were successfully prepared via reactive sintering of Al₂O₃ and MgO raw powders followed by hot isostatic pressing (HIP) using CaO as the sintering additive. The effects of CaO on the densification process, microstructure and optical quality of samples were investigated. It was found that the amount of CaO played an important role in the sintering process. By adding 0.05?wt% CaO, the sample with high transmittance (82.3% at 400?nm), small grain size (<5?μm) and high strength (228?±?15?MPa) was obtained after HIPing at 1550?°C. However, when the amount of CaO increased to 0.1?wt%, non-cubic and columnar-shaped grains generated at low HIP temperatures (1550–1650?°C), which severely reduced the optical quality of resulting samples. The grains were calcium aluminates, whose formation was closely related to the molar ratio of Al₂O₃/MgO, CaO amount and sintereing temperature.     

Preparation of CaO granules using the granulation method

ABSTRACT

Improving the hydration resistance of CaO particle in manufacturing and application of free CaO-containing materials has practical significance. In this study, CaO granules was made from Ca(OH)₂ particles, which were fabricated by the granulation method. The results showed that the hydration resistance of the CaO granules which was prepared under 1700?r?min^?1 was the best, the CaO granules was sintered well in calcination process, the shell of CaO granules was relatively dense, which improves the hydration resistance of CaO granules, and the rate of hydration weight increment was 0.58% after placed in the air for 20 days under a temperature of 10–14°C and a relative humidity of 57–81%.     

Effect of titanium chelating compound on hydration resistance of CaO material

The hydration resistance of CaO materials prepared by Ca(OH)₂ calcination with titanium chelating compounds is investigated in this paper. The crystalline phases and microstructure characteristics of sintered specimens were studied by X-ray diffraction (XRD), define FTIR spectroscopy, scanning electron microscopy (SEM), and energy dispersive spectrometer (EDS). The results showed that the hydration resistance of CaO samples was improved significantly, especially for samples with 9 wt% Ti chelating compound. The specimens with Ti chelating compound showed an increase in bulk density and a decrease in apparent porosity after heating when compared to the specimens without additive. The grain surface of CaO grain and the gaps between the CaO grain boundaries were covered with calcium phosphate glass phase, calcium phosphate showed two different shapes: irregular shape and rod shape. The formation and distribution of these two forms were the key factors that affecting the hydration resistance of CaO samples.     

Phase equilibria studies in the CaO–SiO2–Al2O3–MgO system with CaO/SiO2 ratio of 0.9

Phase equilibria and liquidus temperatures in the CaO–SiO₂–Al₂O₃–MgO system at a CaO/SiO₂ weight ratio of 0.9 in the liquid phase have been experimentally determined employing high-temperature equilibration and quenching technique followed by electron probe X-ray microanalysis. Isotherms at 1573, 1623, 1673, and 1773 K were determined and the primary phase fields of wollastonite, melilite, olivine, periclase, spinel, and corundum have been located. Compositions of the olivine and melilite solid solutions were analyzed and discussed. Comparisons between the newly constructed diagram, existing data, and FactSage predicted phase diagrams were performed and differences were discussed. The present study will be useful for guidance of industrial practices and further development of thermodynamic modeling.