Effect of Biochar as Reductant on Magnetizing-roasting Behavior of Pyrite Cinder

The effect of biochar substituted for anthracite as reductant on magnetizing-roasting pyrite cinder was investigated.The key of magnetizing-roasting is the gasification reaction between reductants and CO2.Since biochar could react with CO2 more rapidly at lower temperature,the reactivity of biochar is better than that of anthracite.The gasification of biochar could produce reducing condition ofφCO/(φCO+φCO2)about 10%-20% between 700-800 ℃,which is in accord with the atmosphere and temperature of Fe2O3 reduction.So it is beneficial to the reduction of iron mineral of pyrite cinder.Compared with anthracite,biochar could decrease the roasting temperature from825 to 750 ℃ and roasting time from 20 to 15min,which shows that a better effect of magnetization could be obtained in the condition of lower temperature and shorter time.Using biochar as reductant,iron concentrate extracted from pyrite cinder as about 64%iron grade could be produced,and the recovery is over 90% under the condition of above 90% grinding particle less than 0.045 mm and magnetic intensity of 0.124-0.194 T.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

串行及并行A/D转换器在高速数据采集中的采样差别性分析

串行和并行接口模式是A/D转换器诸多分类中的一种,但却是应用中器件选择的一个重要指标.在同样的转换分辨率及转换速度的前提下,不同的接口方式不但影响了电路结构,更重要的是将在高速数据采集的过程中对采样周期产生较大影响.本文通过12位串行ADC ADS7822和并行ADC ADS774与AT89C51的接口电路,给出二者采样时间的差异性.     

CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

防腐蚀涂料的性能与选择

介绍并比较几种常用的防腐蚀涂料的品种、组成和性能特点，提出防腐蚀涂料的选择原则。     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

给水管网计算中的数据转换方法

在给水管网计算中,通过建立环-管段矩阵、环-节点矩阵以及输入节点流量、节点坐标等少量数据,通过计算和数据转换,便可求得经济管径、管段设计流量、节点水压值、水厂供水量、管网造价、年费用折算值等。采用该方法进行管网计算,可以减少40%～70%的计算时间。     

Σ-ΔA/D转换技术及仿真

Σ－ΔＡ／Ｄ转换技术近年来颇受重视，因为基于该技术的Ａ／Ｄ转换器能达到很高的分辨率（１６ｂｉｔ以上），并另具一系列优点。本文对Σ－ΔＡ／Ｄ转换器的基本原理，包括过采样（Ｏｖｅｒｓａｍｐｌｉｎｇ），噪声成形（ＮｏｉｓｅＳｈａｐｉｎｇ），以及数字抽取滤波（ＤｉｇｉｔａｌＤｅｃｉｍａｔｉｏｎＦｉｌｔｅｒｉｎｇ）等内容，均作了叙述。作者还对一个２０ｂｉｔΣ－Δ转换器的算法进行了计算机仿真。该转换器采用了高阶ＭＡＳＨ噪声成形技术，而其数字抽取滤波部分则由梳状滤波器与级联的半带滤波器构成。文章中给出了仿真结果。     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

新型海洋涂料技术

本文综述了符合时代要求的海洋涂料新技术及其发展趋势。