复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

基于数值模拟的挤压参数对AZ91镁合金管转角焊合室分流挤压焊合压力的影响规律研究

提出了一种镁合金管材转角焊合室分流挤压新工艺，该工艺可在有效延长焊合室长度和焊合时间前提下保证舌针刚度，从而保证管材尺寸精度，并且可通过转角剪切变形机制增加预焊合金属变形量和动态再结晶程度，从而有利于提高管材性能和焊缝焊合性能。利用有限元法揭示了转角焊合室分流挤压成形过程中金属的流动特征，应变分布特征和焊合室内的静水压力分布特征。结果表明，整个挤压过程无金属折叠，从而保证管材的表面质量；流经转角后预焊合金属变形量明显增加，有利于提高管材质量和焊缝质量。最后，研究揭示了坯料初始温度，挤压速度和模具转角对焊合室内静水压力的影响规律。结果表明，随着挤压速度的增加和模具转角的增大，转角焊合室内静水压力增大；随着坯料预热温度的增加，转角焊合室内静水压力呈先增大后减小的趋势。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

An integrated model for analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding

An integrated model of ultrasonic vibration enhanced friction stir welding (UVeFSW) is developed by integrating the thermal-fluid model with the ultrasonic field model and tool torque model. The tool torque and the heat generation rate at tool/workpiece contact interfaces are coupled with the interfacial temperature, strain rate and ultrasonic energy density. The model is used in quantitatively analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding (FSW). The results show that ultrasonic vibration reduces the flow stress, which results in a decreasing of tool torque, interfacial heat generation rate and interfacial temperature. The complicated interaction of ultrasonic energy with the thermal processes in FSW leads to a gentle thermal gradient and an enhanced plastic material flow in UVeFSW. The model is validated by a comparison of the calculated thermal cycles and tool torque at various welding parameters with the experimentally measured ones.     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Effect of metallurgical evolution during post-weld aging treatment on localised corrosion of resistance spot welding joints of A286 superalloy

The combined effect of resistance spot welding and precipitation hardening on the localised corrosion of A286 superalloy is studied. The specimens tested by double loop electrochemical potentiokinetic reactivation were welded in the solution treated condition, and then subjected to different precipitation hardening treatments. For both base metal and weld nugget, the maximum localised corrosion is reached when η phase is clearly observable. The fact that the localised corrosion resistance of weld nugget is different from that shown by base metal may be explained by the segregation of Ni and Ti towards the interdendritic region of weld nugget (studied by using scanning electron microscope/energy dispersive X-ray analysis).     

Bearing capacity of horizontally layered geosynthetic reinforced stone columns

In very soft soils, the bearing capacity of stone columns may not improve significantly due to very low confinement of the surrounding soil. Therefore, they may be reinforced with geosynthetics by using vertical encasement or horizontal layers. Very limited studies exist on horizontally reinforced stone columns (HRSCs). In this research, some large body laboratory tests have been performed on horizontally reinforced stone columns with diameters of 60, 80, and 100?mm and groups of stone columns with 60?mm diameter. Results show that the bearing capacity of stone columns increases by using horizontally reinforcing layers. Also, they reduce lateral bulging of stone columns by their frictional and interlocking effects with stone column aggregates. Finally, numerical analyses were carried out to study main affecting parameters on the bearing capacity of HRSCs. Numerical analysis results show that the bearing capacity increases considerably with increasing the number of horizontal layers and decreasing space between layers.     

热轧带钢卷取机夹送辊修复材料与再制造工艺研究

为了提高热轧带钢卷取机夹送辊表面的修复质量，通过正交试验优选出埋弧堆焊专用焊丝ZJ－11和ZJ－12，过渡层选用ZJ－11药芯焊丝，堆焊硬层选用ZJ－12药芯焊丝，采用优选出的焊丝进行了堆焊修复试验。试验结果显示，堆焊焊缝金相组织中的马氏体更加细化，且碳化物颗粒明显增加，材料的硬度与耐磨性显著提升。研究表明，通过采用合理的再制造工艺对热轧带钢卷取机夹送辊进行修复，修复后满足要求，使用效果良好，显著提高了夹送辊的使用寿命。     

双光束激光焊匙孔动态特征分析

文中研究了高功率单光束激光焊与双光束激光焊过程中匙孔动态特征的差别. 结果表明，单光束激光焊及双光束激光焊接过程中匙孔均处于从产生到湮灭的剧烈波动的过程，不同于单光束激光焊匙孔的形成、长大、维持、缩小、湮灭过程，双光束激光焊的匙孔还存在分离长大及合并缩小的过程；在相同的焊接参数及焊缝具有相同熔深的条件下，双光束激光焊匙孔的波动频率约为单光束激光焊的2/3，单光束激光焊匙孔的开口面积均值约为双光束激光焊匙孔开口面积的1/2，开口面积的波动变异系数约为单光束激光的2倍，即双光束激光焊过程中匙孔较单光束激光焊的具有较高稳定性.     

Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.