100 MeV质子回旋加速器二期辐照效应管道设计

针对中国原子能科学研究院100 MeV质子回旋加速器上的单粒子效应辐照装置进行了二期管道设计，采用八极磁铁校正法对束流进行了扩束及均匀化，最终在靶上得到了一个30 cm×30 cm、均匀性好于92%的均匀分布的束斑，满足了单粒子效应实验的需求。为降低靶站处的束流能散及中子本底，采用两级降能的方案，在偏转磁铁前放置1个降能片，将能量分为100 MeV和40 MeV两档，并分别针对这两个能量点进行方案设计，束流利用率均在42%以上。公差分析结果表明，四极磁铁对靶上束斑均匀性的影响大于八极磁铁，安装过程中应优先保证四极磁铁的安装公差。     

Design and performance analysis of an iterative flux sliding-mode observer for the sensorless control of PMSM drives

To improve the performance of permanent magnet synchronous motor (PMSM) drives, a sensorless control scheme based on a novel iterative flux sliding-mode observer (IFSMO) is proposed in this paper. Two major drawbacks of the conventional sliding-mode observer (SMO), namely, chattering phenomena and high-order harmonics, are discussed. These drawbacks affect the estimation accuracy of the SMO and reduce the control reliability of the system. To eliminate high-order harmonics, a flux SMO is designed by expanding the PMSM state equations with the PM flux. The flux SMO estimates the rotor speed and position using the flux linkage instead of back-EMF information. Moreover, to reduce the chattering in the estimation results, the proposed flux SMO is iteratively used in one current sampling period to adaptively adjust the observer gain. An overall PMSM sensorless control system based on the proposed IFSMO is designed, and an experimental platform using the TMS320F28335 digital signal processor (DSP) controller is built. The superior chattering reduction and harmonic suppression characteristics of the proposed IFSMO are experimentally validated, and the experimental results verify the feasibility of using the proposed IFSMO-based PMSM sensorless scheme in practical applications.     

基于参数预标定的长行程PMLSM无传感器控制

为了解决长行程定子不连续永磁直线同步电机存在的因无法全程安装位置传感器和不同动子和定子之间的电磁参数不固定所造成的控制性能下降的难题,提出一种在每一段定子内先进行参数标定,再进行速度控制的控制系统设计。首先,在动子进入过程中,对电机进行电磁参数标定,根据标定参数对控制器参数进行调整,以达到更好的控制效果。然后,使用无位置传感器控制系统使动子快速达到设定速度值并稳定运行。实验结果表明:动子进入过程参数标定精度分别为0.002Wb和0.000 4H;无位置传感器控制中位置估计精度为0.63mm,速度收敛时间为0.45s,稳态误差为0.02m/s。基本满足永磁直线同步电机用于长行程运输的控制快速性、稳定性等要求。     

平行流式电机周向水套结构参数对散热性能影响研究

针对电力机车上某功率密度为1.27 kW/kg的平行流式电机周向水套结构的散热问题进行了研究。首先利用热阻网络法建立了平行流多通道截面的热阻数学模型;然后借助FLUENT软件对水套的电机散热过程进行了数值模拟,并对结构参数进行了优化;最后通过实验验证了计算的正确性。结果表明:当通道孔数n增大时,总热阻普遍减小;当通道单孔宽度x增大时,总热阻先增大后减小,当n=6个、x=1.670 mm时,水套具有最佳的散热性能;水套各测温点的数值模拟温度与实验测量温度之间的相对误差均低于5.00%。     

A Monte Carlo study of spring-exchange magnets containing ultra-high coercive phases

The aim of the present work is to study magnetization processes in the spring-exchange magnetic composites containing magnetically soft, hard and ultra-high coercive phases, experimentally found in Tb-Fe-B-Nb group of alloys. In order to modeling hysteresis loops a special Monte Carlo procedure,suitable for irregular geometry of the composites, was applied. The obtained results indicate that sufficiently strong coupling between soft and hard magnetic phase leads to collective, single-phase-like movement of such phases, which in turn, causes increase of the coercivity and internal magnetic energy.     

铁尾矿-煤矸石-污泥复合烧结砖的制备与特性

以铁尾矿和煤矸石为主要原料,掺加部分污泥及其他辅料制备铁尾矿-煤矸石-污泥复合烧结砖,分析了铁尾矿、煤矸石、污泥与其他辅料的矿物组成、化学成分及粒度特征,考察了铁尾矿、煤矸石和污泥配比、坯体成型压力、烧结温度对烧结砖质量的影响,借助XRD、SEM、ICP等手段分析了烧结砖中重金属离子的固化效果与微观结构。结果表明:铁尾矿-煤矸石-污泥复合烧结砖的制备条件以铁尾矿∶煤矸石∶污泥∶页岩配比为54∶30∶6∶10,成型压力20 MPa为宜;烧结温度1 100℃,保温时间3.0h。制品经过高温烧结后,物料中重金属被固化或部分挥发,重金属离子浸出率大小为:Pb~(2+)Cu~(2+)Zn~(2+)Cr~(3+),且符合GB5085.3—2007的规定。显微分析表明:未烧砖坯断面多为离散颗粒、大小和排列均无序;高温烧结后新生成的玻璃晶相明显增加而呈现液相固结,显微表面更加平整均匀致密。     

Numerical study of flow distribution uniformity for the optimization of gradient porosity configuration of porous copper fiber sintered felt for hydrogen production through methanol steam reforming micro-reactor

A macroscopic numerical method is proposed to study the flow distribution uniformity of a novel porous copper fiber sintered felt (PCFSF), which has gradient porosities and was developed as the methanol steam reforming micro-reactor catalyst support for hydrogen production for fuel cell applications. The macroscopic porous media developed by the ANSYS/FLUENT software is used to represent the PCFSF. Our results indicate that the gradient porosity can reshape the flow distribution of PCFSFs greatly, thus producing significant influence on their performance. It is further revealed that, for a PCFSF with a determined gradient porosity configuration but different reactant feed directions, the velocity uniformity can be used as a quantitative criterion to evaluate the performance of hydrogen production. Furthermore, new gradient PCFSFs are produced according to the flow distribution of original gradient PCFSFs. The preliminary experimental results of the new gradient PCFSFs of 0.8-0.9-0.7 and 0.7-0.9-0.8 exhibit better methanol conversion and H₂ flow rate. This indicates that the numerical method can be used for the optimization of PCFSFs' gradient porosity configuration, which consists of the shape and position of the interfaces between different porosity portions, the number of interfaces and the porosity distribution in different portions.     

高能同步辐射光源储存环快校正磁铁电源设计

高能同步辐射光源（HEPS）具有0.1 nm·rad的超低发射度，对束流稳定度提出了较高要求，研制1台高性能快校正磁铁电源用来提高快速轨道反馈系统（FOFB）的性能以提升束流稳定度。电源样机采用新颖的多电平级联拓扑结构提升电源样机的动态性能，使用基于数字控制的新颖控制方法实现样机的动态性能提升。软件仿真与样机试验数据证明，电源样机具有10 kHz小信号带宽、电源阶跃响应时间小于70 μs、输出电流纹波低于20 ppm，电源样机可很好地满足HEPS建设需求。