移动通信系统中功率控制研究

在阐述功率控制在移动通信系统中的发展过程的基础上，着重研究了WCDMA系统的功率控制，最后对功率控制未来的研究方向做了简要的分析。     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

深穿透复合射孔技术在中原油田的应用

深穿透复合射孔是一项把射孔与高能气体压裂两种技术有机地结合在一起的综合改造油气层的新技术。重点对它的技术原理，包括设计原理、枪身内火药燃烧气体对射孔孔眼的冲刷作用原理、火药燃烧气体射流的高能气体压裂作用原理等进行了研究与探讨，同时对它的施工工艺、现场应用等方面进行了阐述，经中原油田189口井现场应用证明，其工艺简便，成本低廉，可实现多层跨隔层使用，处理后增产效果显著，投入产出比高，可代替传统的聚能射孔技术，具有广阔的推广和应用价值。     

Modelling the impact of energy taxation

Energy taxation in Sweden is complicated and strongly guides and governs district energy production. Consequently, there is a need for methods for accurate calculation and analysis of effects that different energy tax schemes may have on district energy utilities. Here, a practicable method to analyse influence of such governmental policy measures is demonstrated. The Swedish Government has for some years now been working on a reform of energy taxation, and during this process, several interest groups have expressed their own proposals for improving and developing the system of energy taxation. Together with the present system of taxation, four new alternatives, including the proposed directive of the European Commission, are outlined in the paper. In a case study, an analysis is made of how the different tax alternatives may influence the choice of profitable investments and use of energy carriers in a medium‐sized district‐heating utility. The calculations are made with a linear‐programming model framework. By calculating suitable types and sizes of new investments, if any, and the operation of existing and potential plants, total energy costs are minimized. Results of the analysis include the most profitable investments, which fuel should be used, roughly when during a year plants should be in operation, and at what output. In most scenarios, the most profitable measure is to invest in a waste incineration plant. However, a crucial assumption is, with reference to the new Swedish waste disposal act, a significant income from incinerating refuse. Without this income, different tax schemes result in different technical solutions being most profitable. An investment in cogeneration seems possible in only one scenario. It is also found that particular features of some alternatives seem to oppose both main governmental policy goals, and intentions of the district heating company. Copyright © 2002 John Wiley & Sons, Ltd.     

联产供冷与电力供冷能耗比较分析

文中将两种供冷能耗比较分解成用电煤耗差、用热煤耗量、增加产汽用电煤耗量三部分进行分析，按照热量法得出在目前一般情况下联产供冷比电力供冷通常费能和定性定量结论，为全面研究比较热电冷联产与分产的能耗奠定一个基础。