Influence of aluminum phosphate on the tribocorrosion performance of chemically bonded phosphate ceramic coatings

In this study, chemically bonded phosphate ceramic coatings (CBPCCs) with different contents of aluminum phosphate (AP) are prepared on stainless steel (AISI 304L). Differential scanning calorimetry, X-ray diffraction, contact angle test, and a tribocorrosion experiment are carried out to clarify the role of AP in the tribocorrosion performance of CBPCCs. The results show that, with the increase in the AP content, the enthalpy of curing increases because of the greater formation of the bonding phase AlPO₄. Both in static corrosion and in tribocorrosion, the corrosion current density of CBPCCs achieves the lowest value when the weight ratio of AP to polytetrafluoroethylene is about 0.78. Additionally, the influence mechanism of AP on tribocorrosion is clarified. AlPO₄ from the reaction between AP and Al₂O₃ has excellent mechanical properties and can enhance the wear resistance of CBPCCs by reducing the mechanical wear and the increased wear due to corrosion. The alumina particles wrapped by AlPO₄ can form a dense and smooth surface and change the direction of electrolyte propagation, which leads to the increase in the tribocorrosion resistance of CBPCCs.     

Electrodeposition of B,Ni co-doped diamond-like carbon films on AZ91D magnesium alloy: Corrosion and wear resistance

Diamond-like carbon (DLC) possesses brilliant and excellent properties, including excellent corrosion resistance as well as outstanding wear resistance. Ni and B co-doped DLC films were deposited on AZ91D magnesium alloy by electrodeposition under mild conditions (300 V and 25°C). Uniform and dense morphology of co-doped DLC films were observed, and Ni and B were uniformly incorporated into the carbon-based films. Among all the electrodeposits, the appearance of D and G peaks near 1330 and 1570 cm⁻¹ revealed that the as-deposited films were typical DLC films. As the addition of Ni was increased to 0.05 g, the highest microindentation hardness, the lowest friction coefficient, and wear loss were achieved to be 164.5 HV, 0.3, and 0.6 × 10⁻⁵ kg/m, respectively. The amorphous carbon films fabricated at 0.05 g Ni had the lowest corrosion current density and the most positive corrosion potential, which was mainly due to the small and dense granular structure effectively hindering the penetration of corrosion media.     

Wear and thermal behavior of basalt fiber reinforced rice husk/polyvinyl chloride composites

Plant fiber reinforced polymer composites (PFRPs) in practical application are often subjected to both complex friction and variable temperature environments. The present work explores the possibility of reinforcing rice husk/polyvinyl chloride (RH/PVC) composites with basalt fibers (BF) for developing a new wear resistant material with improved thermal stability. The results showed that the structural strength and wear resistance of the composites increased at first and then decreased with an increasing ratio of BF/RH, the highest value occurred at a BF/RH ratio of 8/42. The thermal stability of composites had a positive relationship with BF/RH ratio. The composites added with BF all possessed improved performance in comparison with unadded composites. Hence, the findings of this article proposed some new perspectives on improving the wear resistance and thermal stability of PFRPs that would broaden their practical application.     

CrN和CrN/Ag涂层的真空高温摩擦磨损性能*

为改善涂层在真空、高温等苛刻条件下的摩擦学性能，利用中频直流磁控溅射技术在硅片和316L不锈钢上沉积了CrN和CrN/Ag涂层，利用扫描电镜、透射电镜和X射线衍射仪对涂层的成分及相结构进行了表征，通过划痕测试仪、纳米压痕仪和摩擦磨损试验机测试了涂层的力学及摩擦学性能。结果表明：添加Ag元素以后，CrN/Ag涂层硬度及承载能力有所减小，但结合强度增加；真空高温环境下CrN与CrN/Ag涂层摩擦因数随温度升高呈下降趋势，其中CrN涂层通过软化镀层减小剪切强度和阻力，从而减小摩擦因数，CrN/Ag涂层主要通过高温产生的热驱动力诱导表面Ag润滑膜的形成来减小摩擦因数；CrN涂层依靠自身剪切特性参与摩擦，而CrN/Ag涂层在真空高温下具有自润滑和持续润滑性能，作为自润滑零部件具有潜在的应用价值。     

Corrosive wear behavior of HVOF-sprayed micro-nano-structured Cr3C2–NiCr cermet coatings under aqueous media

A novel micro-nano-structured Cr₃C₂–NiCr cermet coating was prepared on 316L stainless steel by high-velocity oxygen fuel spraying technology (HVOF). Cermet coatings with different contents of micro-and nano-sized Cr₃C₂ particles as the hard phase and a NiCr alloy matrix as the bonding phase were prepared and characterized in terms of porosity, microhardness, and corrosive wear resistance in a 3.5% NaCl solution and artificial seawater. Compared to nanostructured coatings, micro-nano-structured coatings avoid decarburization and reduce nanoparticle agglomeration during the spray process, and mechanical and electrochemical properties were improved in comparison with those of conventional coatings. The micro-nano-structured Cr₃C₂–NiCr coating rendered low porosity (≤0.34%) and high microhardness (≥1105.0HV_0.3). The coating comprising 50% nano-sized Cr₃C₂ grains exhibited the best corrosive wear resistance owing to its densest microstructure and highest microhardness. Furthermore, compared to static corrosion, the dynamic corrosion of the coatings led to more severe mechanical wear, because corrosion destroyed the coating surface and ions promoted corrosion to invade coatings through the pores during corrosion wear.     

Investigation of La0.6Sr0.4Co1-xNixO3-δ (x=0, 0.2, 0.4, 0.6, 0.8) catalysts on solid oxide fuel cells anode for biogas dry reforming

The introduction of catalyst on anode of solid oxide fuel cell (SOFC) has been an effective way to alleviate the carbon deposition when utilizing biogas as the fuel. A series of La_0.6Sr_0.4Co_1-xNi_xO_3-δ (x = 0, 0.2, 0.4, 0.6, 0.8) oxides are synthesized by sol-gel method and used as catalysts precursors for biogas dry reforming. The phase structure of La_0.6Sr_0.4Co_1-xNi_xO_3-δ oxides before and after reduction are characterized by X-ray diffraction (XRD). The texture properties, carbon deposition, CH₄ and CO₂ conversion rate of La_0.6Sr_0.4Co_1-xNi_xO_3-δ catalysts are evaluated and compared. The peak power density of 739 mW cm^?2 is obtained by a commercial SOFC with La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst at 850 °C when using a mixture of CH₄: CO₂ = 2:1 as fuel. This shows a great improvement from the cell without catalyst for internal dry reforming, which is attributed to the formation of NiCo alloy active species after reduction in H₂ atmosphere. The results indicate the benefits of inhibiting the carbon deposition on Ni-based anode through introducing the La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst precursor. Additionally, the dry reforming technology will also help to convert part of the exhaust heat into chemical energy and improve the efficiency of SOFC system with biogas fuel.     

Differences in indentation and wear behaviors between the two sides of thermally tempered soda lime silica glass

Thermal tempering is an industrial process widely used to make soda lime silica (SLS) glass panels stronger and tougher. During the tempering process, the upper and bottom sides of the glass may experience different cooling rates, and thus, their properties could be different. This study characterized changes in surface composition and subsurface glass network structures as well as indentation and wear resistance properties of the air- and tin-sides of 6-mm-thick SLS window panels faced toward the upper and sliding roller sides during thermal tempering. The results showed that although the chemical and structural differences detected with X-ray photoelectron spectroscopy and specular reflection infrared spectroscopy are subtle, there are large differences in nanoindentation behaviors and mechanochemical wear properties of the SLS glass surface. The findings of this study provide further insights into the performance difference between the air- and tin-sides of the SLS glass panel treated with thermal tempering.     

“Peel cutting” – A new cutting method for difficult-to-cut workpieces with hard oxide surfaces

A new cutting method named “peel cutting” is proposed in this research to suppress notch wear in machining of metals with hard oxide surfaces. In general, metals are produced by hot deformation processes like rolling, forging, and extrusion, which cause hard oxide surfaces called scales on their surfaces. These hard scales need to be removed first in machining of precision parts. However, the machining causes the severe notch wear at the depth-of-cut position, where the tool contacts the hard scale. To solve this problem, the proposed peel cutting avoids this direct contact between the tool and the scale by inclining the end cutting edge at an extremely large inclination (oblique) angle. This extremely oblique cutting changes the material flow and generates a “burr-like chip”. In the proposed cutting method, the tool contacts only soft non-oxide metal under the scale during cutting. Cutting of titanium alloy Ti–6Al–4V is conducted by modifying commercial tools to provide extremely large inclination angles, and it is clarified that an inclination angle of 70 deg or greater is required to realize the proposed cutting. Tool wear in the proposed cutting of the alloy with a hard scale is also observed in comparison with the ordinary cutting, and the result verifies that the notch wear can be suppressed successfully by the proposed peel cutting.     

Recent advances during CH4 dry reforming for syngas production: A mini review

Given the continuing issues of environment and energy, methane dry reforming for syngas production have sparked interest among researchers, but struggled with the process immaturity owing to catalyst deactivation. This review summarizes the recent advances in the development of efficient and stable catalysts with strong resistance to coking and metal sintering, including the application of novel materials, the assessment of advanced characterizations and the compatibility to improved reaction system. One feasible option is the crystalline oxide catalysts (perovskite, pyrochlore, spinel and LDHs), which feature a fine metal dispersion and surface confinement effect via a metal exsolution strategy and exhibit superior reactivity and stability. Some new materials (h-BN, clays and MOFs) also extend the option because of their unique morphology and microstructure. It also is elaborated that progresses were achieved in advanced characterizations application, leading to success in the establishment of reaction mechanisms and attributions to the formed robust catalysts. In addition, the perspective described the upgrade of reaction system to a higher reaction efficiency and milder reaction conditions. The combination of efficient reaction systems and robust catalysts paves a way for a scaling-up application of the process.