非常规气藏储层改造体积评价方法研究

为精确描述非常规气藏压裂后的复杂流动特征及定量评价储层改造体积（SRV），利用自主研发的缝网重构算法“破裂树生长法”建立压后缝网模型，并以此为基础提出了使用拟稳态流动时特定的压力等值线来确定SRV范围的定量评价方法，最后以长宁201井区为例进行了矿场实例分析。该方法根据微地震监测点的位置，重构出微裂缝网的连通关系。在复杂微裂缝网的基础上建立离散裂缝地质模型并进行生产数值模拟，根据数值模拟结果的压力分布精确划定SRV的范围。利用该方法计算出长宁201井区的SRV体积为0.052 1 km3，以该缝网模型的数值模拟产量预测结果符合实际生产规律，方法实用性较好。     

煤峪口矿81010工作面煤层底板裂隙发育特征及防治

针对煤炭开采过程中出现的突水事故,采用RFPA数值模拟软件建立采动模型,对底板裂隙破断过程和声发射进行模拟,研究煤层底板采动裂隙扩展突水通道,结果表明:离断层越近,断层内水压导升高度越高,断层出现活化,裂隙扩展发育,最终贯通形成导水通道,在进行注浆改造后,单个钻孔的最大涌水量为8 m³/h,说明注浆加固防治水效果较好,能确保工作面的安全回采。     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Cyberbullying: Effect of emergency perception on the helping tendencies of bystanders

The effect of the emergency perception of bystanders of cyberbullying victims on helping behaviors is often neglected in research on cyberbullying. In this study, we explored the influence of this cognitive factor on cyber-bystanders’ helping tendencies as well as elucidated possible underlying processes. The results of two studies were reported. In Study 1, 150 undergraduates read a true case of a girl experiencing cyberbullying. The results indicated that when the participants perceived the victim’s situation to be more critical (i.e., higher emergency perception), their helping tendencies were stronger, partly through increased state empathy followed by feelings of responsibility to help. In Study 2, we randomly assigned 300 undergraduates to two groups. The low emergency group read the same cyberbullying case as Study 1, whereas the cyberbullying case read by the high emergency group contained additional emergency information of the victim. The results indicated that the high emergency group expressed stronger helping tendencies than did the low emergency group. This effect was caused by a stronger perception that the victim was in an emergency situation, which not only strengthened the participants’ helping tendencies directly but also indirectly through increasing their state empathy and feelings of responsibility to help.     

Thermal shock response behaviour of carbon fibre reinforced silicon carbide matrix composites prepared by chemical vapour infiltration at different heating rates

The present work investigated the effects of thermal cycles in air on the tensile properties of a two-dimensional carbon fibre reinforced silicon carbide composite (2D C/SiC) prepared by chemical vapour infiltration at different heating rates. The composite was exposed to different cycles of thermal shock between 20 °C and 1300 °C in air. The damage mechanisms were investigated by AE online monitoring and fractured morphology offline analysis. The tensile strength of 2D-C/SiC decreases with increasing thermal cycles. However, the modulus only decrease within 40 cycles. Due to oxidation, with the decrease in heating rate, the residual properties of the material decrease more obviously. Meanwhile, the results of AE online monitoring and fracture analysis show that the matrix damage is more serious at higher heating rate and that more delamination occours in tensile fractures. The above results indicate that for the thermal shock of 2D C/SiC composites in air, oxidative damage plays a key role in the residual properties.     

Mechanical properties and thermal shock in thin ZrO2–Y2O3–Al2O3 films obtained by the sol-gel method

Thin multilayer coatings of ZrO₂–Y₂O₃–Al₂O₃ were prepared using the sol-gel method and dip-coating technique in order to advance in the study of what influence the incorporation of Al₂O₃ has on films of Y₂O₃-doped ZrO₂, investigating its role in the synthesis of the solutions and in the characteristics and properties of the coatings. After the characterization of the solutions used in the process, the microstructure of the films was studied and their mechanical behaviour and resistance to thermal shock were determined so as to optimize the characteristics and functionality of these coatings. With increased alumina content, 3YSZ-Al₂O₃ (20 mol%), the cubic phase of the zirconia disappeared completely at the sintering temperature used (700 °C), resulting in the tetragonal phase with Al in solution. There was also a decrease in the coatings' hardness and Young's modulus, and an increase in toughness and resistance to thermal shock. These results allow guidelines to be established for the design of multilayer structures that are, tougher, more resistant, and have improved surface properties.     

Failure and fragmentation of ceramic target with varying geometric configuration under ballistic impact

The failure and fragmentation of monolithic bare alumina 99.5% ceramic target and energy dissipation of steel 4340 projectile have been studied in a series of ballistic experiments carried out, with the incidence velocities in a range, 122–290 m/s. The velocity drop and energy dissipation increased with incidence velocity for 10 mm thick target with damage zone extended upon the whole area of rear face at higher velocities. The ballistic results obtained with the 10 mm thick target have been compared with the ballistic performance of the 5 mm thick target used in a previous study to explore the effects of target thickness on the failure mechanism. A model for the residual velocity of projectile after perforation of the single layered ceramic target has been developed based on the Lambert Jonas model by using the experimental data available for 5 mm and 10 mm thick alumina 99.5% target against 10.9 mm projectile. The residual velocities and damage patterns were reproduced with a reasonable amount of accuracy by a three-dimensional finite element model developed on commercial ABAQUS/CAE. The effect of obliquity and projectile diameter to target thickness ratio (D/T) on ballistic performance has been determined by the numerical simulation model with impact velocity in a range of 300–500 m/s. A spatial variation of ejected fragments velocity at different time steps was plotted to develop a velocity profile for the ceramic fragments coming out of the target. A semi-empirical model has been proposed for residual velocity after perforation of a monolithic ceramic target, relating to the incidence velocity and projectile diameter to target thickness ratio. The monolithic ceramic targets have been investigated for a comparative assessment of energy dissipation by the ceramic layer to eventually design an efficient front layer of a ceramic based composite armour in future studies.     

Microstructure,mechanical properties,and fracture behaviour of Ti(C,N)-based cermets with a composite structure

Ti(C,N)-based cermets with a composite structure were designed to maintain the balance between strength and toughness. The cermets with the composite structure comprised coarse particles and the matrix, and the coarse particles included fine hard phases compounded in the matrix. A new hard phase grain with a four-layered structure was found. The composite structure of the cermet can contribute to high toughness, and the grain with the four-layered structure in the composite structure imparts high strength and toughness. As the granule size increases, the fracture toughness of the cermets increased, but the hardness and transverse rupture strength (TRS) showed the opposite trend. The toughening mechanisms of the cermet were crack branching, crack bridging, crack deflection, and formation of tear ridges.     

丙烯酸装置循环气压缩机叶片损伤分析与修复

某石化公司丙烯酸装置循环气压缩机在运行过程中,一级叶片突然发生断裂,导致机组停机。采用宏观检查、扫描电子显微镜、能谱分析等方法对断裂叶片进行检验和检测,将断裂叶片的材质、裂纹及断口特征检测结果与疲劳断裂特征和机组运行状况进行对比,确定压缩机叶片的断裂系其达到疲劳寿命所致,提出采用激光熔覆方法对压缩机叶片进行修复,介绍了修复工艺操作程序要点,可为同类故事的处理提供参考。     

矿用直线振动筛结构故障分析

针对煤矿选煤厂直线振动筛工作过程中出现的结构故障问题,采用有限元仿真与现场测试结合的方法对振动筛出现故障的原因进行了分析研究。介绍了振动筛的主要结构及常见故障,并以某矿选煤厂发生大梁断裂的振动筛为例,对该振动筛进行三维建模和有限元模态分析,分析结果表明:随着模态阶次的增加,振型的变化逐渐由移动转为结构本身的扭曲变形。在该振动筛空载工作状态下,选用本质安全型便携式测振记录仪进行振动测试并处理测试信号,得到该振动筛的工作频率。结合模态分析结果和实际测试结果,判断出空载时频繁运行振动筛是造成其大梁断裂的主要原因。根据故障原因给出维护建议:应当尽量避免振动筛在空载或物料较少的状态下长时间运行;在振动筛投入使用前,应预先了解振动筛的工作状态及可能存在的薄弱环节,尽可能避免结构故障,保证振动筛可靠运行。