An investigation of the relation between the temperature dependences of the initial unbalance and the output signal of resistance strain sensor bridge circuits

The relation between the initial unbalance and the output signal of bridge circuits when acted upon simultaneously by the physical factor being measured and the temperature of the surroundings when the bridge is supplied from a voltage or current source is investigated. Analytic relations are obtained which explain the temperature dependence of the useful output voltage under external physical action. __________ Translated from Izmeritel’naya Tekhnika, No. 1, pp. 48–49, 2007.     

具有初曲率板弯曲的边界元分析

由于具有初曲率板弯曲问题的控制微分方程较复杂，直接求解原问题基本解推导边界积分方程较为困难。本文通过引入等效荷载，将此问题的控制微分方程化成与普通板弯曲基本方程形式相同的微分方程，利用一般求解板弯曲问题的边界元法迭代求解，建立了分析具有初曲率板弯曲问题的边界元法。算例表明本方法理论准确、精度良好。     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

安全壳钢衬的初始后屈曲分析

基于Ｄｏｎｎｅｌｌ的非线性板壳理论，认为钢衬壳是一种有特殊缺陷形状的钢衬板，用初始后屈曲渐进分析理论，研究了在温度应力作用下缺陷钢衬板即钢衬壳的初始后屈曲性态。计算了一个四点铆固钢衬壳模型，同时给出了铆钉间距等参数对钢衬壳屈曲极值温度的影响。     

离散效应存在时孤子脉冲的增强压缩

在群速度不匹配的条件下，提出一种提高孤子脉冲压缩效应的新方法．研究表明，若使信号脉冲与泵浦脉冲存在一适当的初始延时，则不但可以提高离散效应单独存在时信号脉冲的压缩比，而且可以提高孤子脉冲的压缩质量．     

一种制做三维牙——颌骨光弹性模型的新方法

本文提出一种用“整体浇注法”制做三维牙——颌骨光弹性模型的新方法,即用价格便宜的石膏做阴模,先制出与真实牙几何相似的牙光弹性模型和模拟牙周膜的乳胶套,将它们粘接好,然后将其放入颌骨石膏阴模的适当位置,浇入环氧树脂混合液,用“二次固化法”进行固化,即可制成三维牙——颌骨整体光弹性模型。此法能保证模型与实物的严格几何相似和牙周的边界条件相似,使实验精度大大提高且工艺简单、成本低。     

Water table fluctuation with a random initial condition

The nonlinear Boussinesq equation is used to understand water table fluctuations in various ditch drainage problems. An approximate solution of this equation with a random initial condition and deterministic boundary conditions, recharge rate and aquifer parameters has been developed to predict a transient water table in a ditch-drainage system. The effects of uncertainty in the initial condition on the water table are illustrated with the help of a synthetic example. These results would find applications in ditch-drainage design.Notation A / tanh t - a lower value of the random variable representing the initial water table height at the mid point - a+b Upper value of the random variable representing the initial water table height at the midpoint - B tanh t - C 4/ - h variable water table height - h mean of the variable water table height - h _m variable water table height at the mid point - h _m mean of the variable water table height at the mid point - K hydraulic conductivity - L half spacing between the ditches - m ₀ initial water table height at the mid point - N Uniform rate of recharge - S specific yield - t time of observation - x distance measured from the ditch boundary - (4/SL)(NK)^1/2 - (L/4)(N/K)^1/2 - dummy integral variable     

Effect of sintering process on microstructure and magnetic properties of high frequency power ferrite

An oxide ceramic process was adopted to prepare high frequency manganese-zinc (MnZn) power ferrite. In combination with the microstructure analysis of material, the influences of sintering process on initial permeability (μi) and high frequency loss in unit volume (Pcv) of MnZn power ferrite were investigated. The results show that in order to obtain fine microstructure and high frequency properties, the preferable sintering temperature and atmosphere are 1230 ℃ and oxygen partial pressure ( PO2) of 4%, respectively.