氮含量及固溶温度对21-6-9奥氏体不锈钢组织和硬度的影响

为了探讨氮含量及固溶温度对21-6-9不锈钢组织和硬度的影响,分别在950、1000、1050和1100 ℃对3种不同氮含量的热轧态21-6-9不锈钢进行1 h固溶处理,通过光学显微镜观察其组织结构,结合Thermo-Calc热力学计算对试验钢的微观组织进行分析,并对其进行硬度测试。结果表明,0.20%~0.28%N的21-6-9不锈钢热轧后沿轧制方向析出铁素体,且钢中铁素体经950~1100 ℃固溶处理可消除,当N含量达到0.34%时,试验钢中不再出现铁素体。随着固溶处理温度的升高,21-6-9不锈钢的晶粒组织长大,硬度降低。N含量的增加可显著提高固溶态21-6-9不锈钢的硬度,其增加程度随固溶处理温度的升高而减弱。     

巨型水轮发电机剪断销研发与质量控制

为获得设计需要的巨型水轮发电机剪断销的剪切力,得到剪切力波动受控的批量剪断销,通过拉伸试验、冲击试验、硬度试验和剪断销剪切试验等讨论了全尺寸剪断销剪切试验的可行性,分析了剪切试验时正常剪断和非正常剪断的剪断销材料性能差异,探究了剪断销的剪切力质量稳定性控制方法。结果表明:控制剪断销料坯的布氏硬度波动,可实现间接控制剪断销剪切强度的波动;通过试验总结的六步法可达到控制批量剪断销质量和剪切力波动的目的。     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Structure,mechanical and thermal properties of Y-doped CrAlN coatings

CrAlYN coatings with different Y contents (0, 5 and 12 at.%) were deposited by cathodic arc evaporation to investigate the influence of Y-addition on the structure, mechanical and thermal properties of CrAlN coatings by using X-ray diffraction, scanning electron microscopy, differential scanning calorimetry, thermal gravimetric analysis and nanoindentation. The structural transformation of single phase cubic Cr_0.42Al_0.58N and Cr_0.39Al_0.56Y_0.05N coatings to cubic–wurtzite mixed Cr_0.32Al_0.56Y_0.12N coating leads to a drop in hardness from (30.2±0.7) GPa of Cr_0.42Al_0.58N and (32.0±1.0) GPa of Cr_0.39Al_0.56Y_0.05N to (25.2±0.7) GPa of Cr_0.32Al_0.56Y_0.12N. The incorporation of 5 at.% Y retards the thermal decomposition of CrAlN, verified by the postponed precipitation of w-AlN and N-loss upon annealing. Correspondingly, Cr_0.39Al_0.56Y_0.05N coating consistently exhibits the highest hardness value during thermal annealing. Nevertheless, alloying with Y exerts an adverse effect on the oxidation resistance of CrAlN.     

木质纤维与水泥共同改良软土的力学性能与微观机制分析

通过压实试验、无侧限抗压强度试验和劈裂试验,分析不同木质纤维含量、水泥含量和固化时间对软土力学性能的影响规律,探讨木质纤维、水泥改良软土的微观机制。结果表明,木质纤维的加入对水泥改良软土的击实特性有显著的影响;木质纤维与水泥可有效改善土体的抗压和劈裂抗拉强度,随着木质纤维含量的增加,改良土的抗压和劈裂抗拉强度呈现出明显的“驼峰”现象,并在木质纤维含量为0.25%时最大;木质纤维与水化产物、软土颗粒形成互锁效应,增大了改良土的摩擦力,同时木质纤维还承担一定的拉伸强度,使改良土的劈裂强度增加。     

Repeated low-velocity impact responses of SiC particle reinforced Al metal-matrix composites

This study aimed to investigate experimentally the repeated low-velocity impact behaviors of SiC reinforced aluminum 6061 metal-matrix composites for different volume fractions and energy levels. In addition, the hardness variations were measured by the Vickers hardness tests from the impacted and impact-free cross-sections of the particle reinforced metal-matrix composites. Low-velocity impact tests were applied to composite samples manufactured by powder metallurgy (in 10, 20, and 30% volume fractions) at two total energy levels (15 and 60 J as single) and in repetitions equal to the sum of these energy levels (5 + 5 + 5 and 20 + 20 + 20 J as repeated). As a result, in increasing the impact number for all volume fractions, the total contact time was shortened and the peak contact force increased, whereas both the permanent central deflection and the absorbed energies reduced. Hence, these variations obtained under repeated impacts (5 + 5 + 5 and 20 + 20 + 20 J) revealed that metal-matrix composites showed a tougher behavior with an increase in the impact numbers from 1st to 3rd, particularly because of the strain hardening effect. Furthermore, an increase in volume fraction from 10 to 30% resulted in an increase in the impact strength under all repeated and single impacts despite changing deformation and damage mechanisms due to increasing the strain hardening effect and particle fractures. The hardness was affected by the volume fraction and increased as the volume fraction increased in both the impacted and impact-free zones. The repeated impact increased the impacted zone hardness more than the single impact for all volume fractions. Additionally, the hardness of the impacted zone under 20 + 20 + 20 J repeated impact was measured as the highest value in the 30% volume fraction. Therefore, metal-matrix composites can behave harder with the strain hardening effect under repeated impacts.     

Chemical Bonding by the Chemical Orthogonal Space of Reactivity

The fashionable Parr–Pearson (PP) atoms-in-molecule/bonding (AIM/AIB) approach for determining the exchanged charge necessary for acquiring an equalized electronegativity within a chemical bond is refined and generalized here by introducing the concepts of chemical power within the chemical orthogonal space (COS) in terms of electronegativity and chemical hardness. Electronegativity and chemical hardness are conceptually orthogonal, since there are opposite tendencies in bonding, i.e., reactivity vs. stability or the HOMO-LUMO middy level vs. the HOMO-LUMO interval (gap). Thus, atoms-in-molecule/bond electronegativity and chemical hardness are provided for in orthogonal space (COS), along with a generalized analytical expression of the exchanged electrons in bonding. Moreover, the present formalism surpasses the earlier Parr–Pearson limitation to the context of hetero-bonding molecules so as to also include the important case of covalent homo-bonding. The connections of the present COS analysis with PP formalism is analytically revealed, while a numerical illustration regarding the patterning and fragmentation of chemical benchmarking bondings is also presented and fundamental open questions are critically discussed.     

微型土压平衡盾构机液压系统故障分析

以微型土压平衡(Earth Pressure Balance,EPB)盾构机推进液压系统作为研究对象,介绍了推进系统的工作原理,对混入空气后的油液黏度和有效体积弹性模量进行分析,建立了推进系统数学模型,并对混入不同百分比空气的系统进行仿真运算,得到了液压缸位移响应和速度响应随系统含气量变化的关系。研究表明:随着液压系统空气含量的增加,液压缸位移响应发生迟滞,速度响应变慢,液压缸在运动时产生振动。结合各液压元件工作原理,依次对实际盾构机推进系统元件进行排气,最终排除了液压系统中混入的空气,为实现盾构机平稳推进提供了理论依据。     

我国中空吹塑行业发展现状及“十四五”期间重点产品、工艺和设备发展方向

从原料、中空成型机和吹塑工艺等方面介绍了我国中空吹塑行业发展现状，并对电子化学品专用超洁净桶、高压储氢四型瓶、全电动中空成型机、微发泡中空成型技术和挤吹聚对苯二甲酸乙二醇酯（PET）容器等在“十四五”期间的重点产品、工艺和设备发展方向进行了展望。