CuO-SiO2气凝胶@TiO2纳米纤维无牺牲剂光催化还原CO2

采用溶胶-凝胶法制备CuO-SiO2复合气凝胶,通过在气凝胶孔道内填充TiCl4,然后将其气相水解,得到了在CuO-SiO2气凝胶表面生长了高结晶度的TiO2纳米纤维(CuO-SiO2@TiO2),纤维直径～16 nm.通过XPS、UPS、UV-Vis DRS、荧光光谱(PL)等表征了材料的结构及光电性能.结果表明,制备的CuO-SiO2@TiO2对可见光有明显吸收,且荧光强度较商用TiO2(P25)大幅降低,光生电子-空穴对更加稳定.再在纳米纤维上负载CuO,所得CuO-SiO2@TiO2/CuO在可见光区的荧光强度进一步增强.以300 W氙灯为光源,分别以CuO-SiO2@TiO2及CuO-SiO2@TiO2/CuO为催化剂,无牺牲剂条件下光催化还原CO2,4 h后甲醇产率分别为1304.0及1589.0μmol/g-cat,转换频率(TOF)分别为0.038及0.046 h–1.循环实验表明,纳米纤维具有较好的光催化稳定性,经过4次光催化循环实验后,CuO-SiO2@TiO2/CuO的保留率～94％,甲醇产率可达1472.0μmol/g-cat,TOF为0.042 h–1.     

Review of electrospun hydrogel nanofiber system: Synthesis,Properties and Applications

Hydrogel-based nanofibers or vice versa are a relatively new class of nanomaterials, in which hydrogels are structured in nanofibrous form. Structure and size of the material directly governs its functionality, therefore, in hydrogel science, the nanofibrous form of hydrogels enables its usage in targeted applications. Hydrogel nanofiber system combines the desirable properties of both hydrogel and nanofiber like flexibility, soft consistency, elasticity, and biocompatibility due to high water content, large surface area to volume ratio, low density, small pore size and interconnected pores, high stiffness, tensile strength, and surface functionality. Swelling behavior is a critical property of hydrogels that is significantly increased in hydrogel nanofibers due to their small size. Electrospinning is the most popular method to fabricate “hydrogel nanofibers,” while other processes like self-assembly, solution blowing and template synthesis also exist. Merging the characteristics of both hydrogels and nanofibers in one system allows applications in drug delivery, tissue engineering, actuation, wound dressing, photoluminescence, light-addressable potentiometric sensor (LAPS), waterproof breathable membranes, and enzymatic immobilization. Treatment of wastewater, detection, and adsorption of metal ions are also emerging applications. In this review paper, we intend to summarize in detail about electrospun “hydrogel nanofiber” in relation to its synthesis, properties, and applications.     

Triggering the aqueous interparticle association of γ‒Al2O3 hierarchical assemblies using divalent cations and cellulose nanofibers

Understanding aqueous dispersion, rheological properties and colloidal stabilisation mechanisms of hierarchically assembled ceramic powders is important for progress in the fields of catalysis, separation and/or adsorption. The present study was designed to evaluate the rheological and sedimentation behaviour of highly loaded aqueous suspensions (up to φ_A = 0.126) containing AlN-powder-hydrolysis-derived, micron-sized, mesoporous, gamma alumina (MA) particulates with a high surface area (～180 m²/g) dispersed with sodium polyacrylate (NaPAA). The as-prepared suspensions were prone to sedimentation and segregation. However, when divalent cations (Mg²⁺, Ca²⁺) or cellulose nanofibers were added, the formation of interparticle association networks in the aqueous suspensions containing MA particles was triggered, facilitating their long-term resistance to sedimentation lasting more than 12 weeks.     

Porous nitrogen-enriched hollow carbon nanofibers as freestanding electrode for enhanced lithium storage

One-dimensional porous carbons bearing high surface areas and sufficient heteroatom doped functional-ities are essential for advanced electrochemical energy storage devices, especially for developing free-standing film electrodes. Here we develop a porous, nitrogen-enriched, freestanding hollow carbon nanofiber (PN-FHCF) electrode material via filtration of polypyrrole (PPy) hollow nanofibers formed by in situ self-degraded template-assisted strategy, followed by NH3-assisted carbonization. The PN-FHCF retains the freestanding film morphology that is composed of three-dimensional networks from the entanglement of 1D nanofiber and delivers 3.7-fold increase in specific surface area (592 m2·g-1) com-pared to the carbon without NH3 treatment (FHCF). In spite of the enhanced specific surface area, PN-FHCF still exhibits comparable high content of surface N functionalities (8.8％, atom fraction) to FHCF. Such developed hierarchical porous structure without sacrificing N doping functionalities together enables the achievement of high capacity, high-rate property and good cycling stability when applied as self-supporting anode in lithium-ion batteries, superior to those of FHCF without NH3 treatment.     

A Skin-Inspired Triboelectric Nanogenerator with an Interpenetrating Structure for Motion Sensing and Energy Harvesting

Rapid advancements in wearable electronics impose the challenge on power supply devices. Herein, a flexible single-electrode triboelectric nanogenerator (SE-TENG) that enables both human motion sensing and biomechanical energy harvesting is reported. The SE-TENG is fabricated by interpenetrating Ag-coated polyethylene terephthalate (PET) nanofibers within a polydimethylsiloxane (PDMS) elastomer. The Ag coating and PDMS are performed as the electrode and dielectric material for the SE-TENG, respectively. The Ag-coated PET nanofibers enlarge the electrode surface area, which is beneficial to increase sensing sensitivity. The flexible SE-TENG sensor shows the capability of outputting alternating electrical signals with an open-circuit voltage up to 50 V and a short-circuit current up to 200 nA in response to externally applied pressure. It is used to sense various types of human motions and harvest electric energy from body motion. The harvested energy can successfully power wearable electronics, such as an electronic watch and light-emitting diode. Therefore, the as-prepared SE-TENG sensor with a pressure response and self-powered capability provides potential applications in wearable sensors or flexible electronics for personal healthcare and human–machine interfaces.     

Microstructure and mechanical properties of hot-pressed SiC nanofiber reinforced SiC composites

This study reports on the preparation and mechanical properties of a novel SiC_nf/SiC composite. The single crystal SiC nanofiber(SiC_nf) reinforced SiC ceramic matrix composites (CMC) were successfully fabricated by hot pressing the mixture of β-SiC powders, SiC_nf and Al–B–C powder. The effects of SiC_nf mass fraction as well as the hot-pressing temperature on the microstructure and mechanical properties of SiC_nf/SiC CMC were systematically investigated. The results demonstrated that the 15 wt% SiC_nf/SiC CMC obtained by hot pressing (HP) at 1850 °C with 30 MPa for 60 min possessed the maximum flexural strength and fracture toughness of 678.2 MPa and 8.33 MPa m^1/2, respectively. The nanofibers pull out, nanofibers bridging and cracks deflection were found by scanning electron microscopy, which are believed can strengthen and toughen the SiC_nf/SiC CMC via consuming plenty of the fracture energy. Besides, although the relative density of the prepared SiC_nf/SiC CMC further increased with the sintering temperature rose to 1900 °C, the further coarsend composites grains results in the deterioration of the mechanical properties for the obtained composites compared to 1850 °C.     

ZIF衍生多孔碳纳米纤维用于高效电容去离子的研究

作为一种环保节能的新兴脱盐技术，电容去离子技术正在成为替代反渗透脱盐和电渗析脱盐的一项重要的脱盐技术。各种碳基材料被广泛地应用于电容去离子电极材料的研究，然而大多数碳基材料为粉末状材料，需要添加黏结剂，这必将导致电极材料电吸附能力的下降。利用静电纺丝技术，将ZIF纳米颗粒和聚丙烯腈混纺，并通过分段高温热处理过程，成功合成了具有柔性结构的整体性多孔碳纳米纤维。由于其具有孔道结构的分级分布和较强的亲水性等优良特性，所制得的多孔碳纳米纤维在1.2 V电压下于500 mg/L NaCl溶液中表现出良好的电吸附性能，脱盐量达到了19.92 mg/g，比普通碳纳米纤维提高了一倍以上。     

混炼方式对螺旋纳米碳纤维增强天然橡胶复合材料力学性能的影响

采用干法和湿法两种混炼工艺制备了螺旋纳米碳纤维(HCNFs)/炭黑(CB)/天然橡胶(NR)复合材料,通过扫描电镜、拉伸试验机和应变扫描仪分别对所制备复合材料的界面形貌、力学性能和Payne效应进行了测试分析,考察了混炼方式对复合材料宏观力学性能及Payne效应的影响。结果表明,与纯CB填料相比,在干湿两种混炼方式下,添加适量的HCNFs(1～6份)能提高HCNFs/CB/NR复合材料的300%定伸应力、扯断伸长率、拉伸强度和硬度。与干法混炼相比,湿法混炼能明显增强HCNFs/CB/NR复合材料的Payne效应,并提升在HCNFs高添加量(2～6份)条件下的拉伸强度和扯断伸长率,这主要源于湿法混炼能够有效改善HCNFs在橡胶基质中的分散性。     

仿贝壳层状MTM/PVA/ANF复合薄膜的制备及其性能研究

通过水蒸发诱导自组装（A）和真空辅助抽滤（F）及其与离心处理（C）组合4种不同方法制备仿贝壳层状结构的蒙脱土/聚乙烯醇/芳纶纳米纤维（MTM/PVA/ANF）复合薄膜，并采用扫描电子显微镜（SEM）、原子力显微镜（AFM）、热重分析仪（TGA）、紫外分光光度计、动态接触角测试仪和拉伸测试仪对复合薄膜的微观结构、热稳定性、透光率、亲水性和力学性能进行表征。结果表明，不同方法（A、CA、F和CF）制得的复合薄膜都呈明显的层状结构，但复合薄膜的透光率、亲水性和力学性能不同。通过F法制备的复合薄膜具有更高的透光率和更好的疏水性；通过CF法制备的复合薄膜具有最优的力学性能，拉伸强度可达132.4 MPa，而通过A法制备的复合薄膜韧性最佳，断裂伸长率可达11.3%。     

Fabrication and Characterization of Highly Oriented Composite Nanofibers with Excellent Mechanical Strength and Thermal Stability

Here, highly‐oriented poly(m‐phenylene isophthalamide)/polyacrylonitrile multi‐walled carbon nanotube (PMIA/PAN‐MWCNT) composite nanofiber membranes with excellent mechanical strength and thermal stability are successfully produced using electrospinning. It is demonstrated that the cooperation of multi‐walled carbon nanotubes (MWCNT) and high‐speed rotating collection is beneficial to the acquisition of highly oriented fibers and effectively improves the mechanical strength of the membrane along the orientation direction. Specifically, the tensile stress of poly(m‐phenylene isophthalamide)/polyacrylonitrile (PMIA/PAN) membrane is enhanced significantly from 10.6 to 20.7 MPa, benefiting from the highly oriented alignment of the fibers as well as the reinforcing effect of MWCNTs on the fibers. Furthermore, the stressing process of single fiber and fiber aggregates is carefully simulated, and the influence of MWCNTs on the mechanical properties of PMIA/PAN‐MWCNT membranes is analyzed comprehensively, providing a meaningful auxiliary means for the study of mechanical properties. In addition, the composite nanofiber membrane has the advantages of both PMIA and PAN, possessing high temperature resistance, flame‐retardancy, and chemical stability, for an ideal high‐temperature material. In short, the as‐prepared PMIA/PAN‐MWCNT composite membrane with excellent comprehensive property emerges a promising application in many fields, especially in high‐tech.