乙烯、丙烯中微量水含量的分析

采用便携式微量水分析仪和库仑法微量水分析仪测定了乙烯、丙烯试样中的微量水含量,对试样的传输系统、进样量的控制、液体试样的气化和水标准气体的制备方法进行了改进,优化了测试条件。以低吸附惰性管线和小死体积单进单出的不锈钢减压器为试样传输系统,缩短了测试时间。采用液态烃闪蒸气化取样进样器气化液体试样并准确控制试样的进样量,可避免液体试样渐次气化对水含量测定结果的影响及对采样钢瓶大小的限制。采用渗透管发生器制备水标准气体,可验证分析结果的准确度。采用库仑法微量水分析仪测定水含量时,试样流量选择600 m L/min较适宜,开封保存15 d之内的卡尔·费休试剂对测定结果无影响。采用便携式微量水分析仪测定水含量时,选择试样流量在400~800 m L/min之间较适宜。两种仪器的测量结果相近,稳定性好,准确度高,回收率在102%~107%之间,相对偏差小于10%。     

浅谈氯碱氢的一种深度脱水工艺

概述了氢的主要工业生产方法和实际应用,详细介绍了氯碱氢三级脱水工艺过程,并运用在线分析手段,准确显示了干燥过程中的氯碱氢水分含量变化规律。     

电信运营商信息安全管控架构及集中策略研究

本文对运营商信息安全集中管控架构演进和信息安全管控策略面临的问题进行了深入分析，提出了信息安全集中管控架构的演进方向建议及对信息安全监控策略工作优化的若干意见。     

Al、Mo含量对铸造钛合金力学性能的影响

运用正交实验 ,考察了Al、Mo含量对Ti Al Mo 1Zr系铸造钛合金力学性能的影响。试验结果表明 :随Al、Mo含量提高 ,铸造合金的强度增加 ,塑性和冲击韧性降低 ,但Al、Mo的交互作用却使合金塑性提高 ,强度和冲击韧性降低     

超细Fe3O4粒子表面包覆酞菁钴性质研究

本文研究了合成载氧体的金属有机化学液相淀积法制造工艺，所得产物经ＴＥＭ、ＸＰＳ、Ｍｏｓｓ－ｂａｕｅｒ谱和Ｂ－Ｈ仪等手段，研究了它的结构和磁性能。实验表明，酞青钴以薄层形式包覆在Ｆｅ＿３Ｏ＿４的表面，封闭了Ｆｅ＿３Ｏ＿４的表面孔洞，稳定了Ｆｅ＿３Ｏ＿４的物相，增强了磁性能。     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

Influence of the oxygen content of low-rank coals on the development of porosity during carbonization

The development of porosity in the course of carbonization of a flame coal, original and pre-oxidized, was studied by means of the adsorption of benzene and carbon dioxide. The results were compared with corresponding data for cokes from a xylitic brown coal. The influence of coal oxygen content on the formation of coke porosity and its thermal dependence is discussed.