Corrosion of structural constituents of 2017 aluminium alloy in acidic solutions containing inhibitors

The objective of this study is to establish the corrosion behaviour of the most important structural constituents of the aluminium alloy 2017 in orthophosphoric acid solutions containing heteropolyoxomolybdate, tungstate and vanadate. These are potential candidates for replacing toxic hexavalent chromium species in stripping solution for anodic coatings. The corrosion rate of the alloy is estimated with linear polarisation method. It decreases from 0.58 mA cm⁻² in uninhibited solution to 0.10 mA cm⁻² in a solution containing heteropolyoxomolybdate species. Microscopic studies reveal that heteropolyoxomolybdate species inhibit corrosion of the matrix and intermetallic Al₁₅(Fe,Mn)₃(Si,Cu)₂ but not Mg₂Si. Intermetallic Al₂Cu remains not corroded. Heteropolyoxotungstate species virtually do not inhibit the corrosion of the alloy. The solution containing vanadium species is not stable with time and the corrosion rate is not determined. Nevertheless, corrosion of the matrix is inhibited, but intermetallics Al₁₅(Fe,Mn)₃(Si,Cu)₂ together with Mg₂Si are dissolved. X-ray photoelectron spectroscopy is used for examination of a corrosion product precipitated on the surface.     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Investigation of the influence of iron-containing abrasives on the corrosion behaviour of the aluminium alloy AlSi1.2Mg0.4

The corrosion resistance of aluminium surfaces is closely linked to the surface state after a grinding process. For years, iron-containing abrasive materials were suspected to lead to increased corrosion susceptibility after processing of aluminium surfaces. To prove a possible correlation between the iron content of an abrasive and the corrosion behaviour of aluminium components, scientific investigations and experimentally practical corrosion tests are necessary. For the current investigation, specimens of a technical Al-Si alloy from the same batch were used. The test specimens were mechanically ground with various resin-bonded model abrasives containing different iron contents. The performed corrosion tests did not reveal a negative influence of the different iron-containing abrasives on the corrosion behaviour of the Al–Si alloy. However, the most sensitive measuring method (electrochemical noise) showed differences in the surface activity depending on the type of abrasive.     

Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

不同方法发酵的酸豆角品质对比分析

本文将研究不同方法发酵的酸豆角品质对比分析。选取质地嫩脆、条形均匀、无病虫害的新鲜豆角为泡制原料。采用自然干法发酵、自然湿法发酵与纯种湿法发酵的发酵方法制作酸豆角。检测发酵过程中，pH值、还原糖含量、总酸含量、总糖含量、亚硝酸盐含量以及氨基酸态氮含量，分析纯种湿法发酵与自然湿法发酵对酸豆角品质的影响。结果表明：纯种湿法发酵25 d后，其pH值和还原糖含量分别为3.92、0.03%，均高于自然湿法发酵；总酸、总糖、亚硝酸盐含量、氨基酸态氮含量分别为0.25%、0.04%、0.01 mg/kg和0.01%，均低于自然湿法发酵。另外，纯种湿法发酵酸豆角的甲氧基乙酸含量为0.37%，乙酸乙酯为0.51%，含水量为81.15%，感官评分为45.52，均高于自然干法发酵。纯种湿法发酵对酸豆角品质的效果最好，亚硝酸盐的含量在发酵后期显著降低，感官评分较高，对豆角工业化生产提供了较好的参考价值。     

New empirical correlation for estimation of vaporization enthalpy of algerian saharan blend petroleum fractions

A Real-coded Genetic Algorithm has been used to develop a new correlation to estimate the enthalpy of vaporization for pure compounds and petroleum fractions as a function of the normal boiling point and specific gravity. In developing the correlation 80% of the data was used and the remaining are used for validation. The results of the proposed correlations are compared to others in literature. The comparison indicates that the proposed model is simple to use and more accurate than the most common correlations for predicting the enthalpy of vaporization of pure compounds and petroleum fractions.     

Adaptive neural network command filtered backstepping control of pure‐feedback systems in presence of full state constraints

An adaptive neural network (NN) command filtered backstepping control is proposed for the pure‐feedback system subjected to time‐varying output/stated constraints. By introducing a one‐to‐one nonlinear mapping, the obstacle caused by full stated constraints is conquered. The adaptive control law is constructed by command filtered backstepping technology and radial basis function NNs, where only one learning parameter needs to be updated online. The stability analysis via nonlinear small‐gain theorem shows that all the signals in closed‐loop system are semiglobal uniformly ultimately bounded. The simulation examples demonstrate the effectiveness of the proposed control scheme.     

Extraction equilibrium conditions of beryllium and aluminium from a beryl ore for optimal industrial beryllium compound production

This study examines the extraction of beryllium and aluminium from a Nigerian beryl ore using Cyanex®272 in kerosene from an aqueous sulphate pregnant solution. Parameters such as extractant concentration and equilibrium pH that dictates the extraction yield were studied. Under the following conditions: temperature 27?±?2°C, phase ratio 1?1, about 45.50 and 46.76% of beryllium and aluminium were extracted by 0.15?mol?L^?1 Cyanex®272 concentration within 30?min. However, the extraction yield of beryllium and aluminium was increased to 91.68% and 97.89% at equilibrium pH of 3 and 4, respectively, for beryllium and aluminium at 27?±?2°C. A 0.05?mol?L^?1 H₂SO₄ solution was found to be adequate for the stripping of about 99.00% Be and 95.40% Al from the loaded organic phase. The pure solutions containing metal ions were accordingly beneficiated to obtain beryllium and aluminium compounds of industrial values.     

A new cladding technology to bond aluminium on magnesium

ABSTRACT

An in situ hot press bonding technology has been developed to clad aluminium on magnesium. Followed by regular hot rolling, magnesium sheets, covered by ductile and corrosion-resistant aluminium without detectable oxides in the interface, are produced. The new technology requires no welding, vacuum, protective atmosphere or barrier layer, and it makes good interfacial strength and rollability. Aluminium–magnesium intermetallic phases are formed along the clad–core interface at elevated temperatures. They are not detrimental under compression but may cause clad-core delamination in tensile strain. However, the tensile failure is more dependent on the formability of magnesium core than on the strength of interface.     

Corrosion behaviour and mechanism of 6082 aluminium alloy in NaCl and Na2SO4 etchants

The corrosion behaviour of 6082 aluminium alloy was studied by measuring the electrochemical impedance spectra and electrode polarization curves. After the electrochemical tests, a microstructural analysis of the samples was conducted by using optical microscopy and electron scanning microscopy techniques to determine the corrosion mechanism. The results show that the Nyquist plot of the electrochemical impedance data in the NaCl solution consists of high- and low-frequency capacitive impedance loops. When ions are added to the NaCl etchant, the Nyquist plots of the electrochemical impedance data are composed of two different curves: a high-frequency capacitive impedance loop and a low-frequency inductive impedance loop. The corrosion current density increases with increasing concentration, and as a result, the corrosion resistance of the aluminium alloy decreases. The microstructures of 6082 aluminium alloy consist of Mg₂Si secondary particles in a large α-Al matrix. Pitting corrosion initially occurs at the boundary between the matrix and secondary particles because the electrode potentials of the matrix and secondary particles are different. Then, corrosion paths develop along the network-like grain boundaries, and finally, massive network-like corrosion occurs throughout the entire alloy.