Morphology-controlled fabrication of nanostructured WO3 thin films by magnetron sputtering with glancing angle deposition for enhanced efficiency photo-electrochemical water splitting

Herein, the tungsten trioxide (WO₃) nanostructure thin films with different morphologies are firstly fabricated by magnetron sputtering with glancing angle deposition technique (MS-GLAD), followed by the post annealed treatment process in air ambient for 2 h. It is demonstrated that the geometry of MS-GLAD setup, mainly substrate position, played a crucial role in determining the morphology, crystallinity, optical transmittance, and photo-electrochemical (PEC) performance of the WO₃ nanostructured thin film. With the different substrate positions in the MS-GLAD system, the WO₃ nanorod film layer could be precisely changed to combine an underlying dense layer with a nanorod layer and then nanocolumnar film. Moreover, the prepared samples' chemical composition and work function are studied by X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS), respectively. The combining WO₃ nanostructure produced high PEC efficiency compared to the single layer of the WO₃ nanorods sample and the dense WO₃ thin film sample. Thus, morphology-controlled nanostructure film based on the MS-GLAD technique in our study provides a simple approach to enhance the photo-anode for PEC water splitting application.     

Sputtered Fe1·5CoNi0.5 coating: An improved protective coating for SOFC interconnect applications

In an attempt to optimize the properties of FeCoNi coating for planar solid oxide fuel cell (SOFC) interconnect application, the coating composition is modified by increasing the ratio of Fe/Ni. An Fe_1·5CoNi_0.5 (Fe:Co:Ni = 1.5:1:0.5, atomic ratio) metallic coating is fabricated on SUS 430 stainless steel by magnetron sputtering, followed by oxidation in air at 800°C. The Fe_1·5CoNi_0.5 coating is thermally converted to (Fe,Co,Ni)₃O₄ and (Fe,Co,Mn,Ni)₃O₄ without (Ni,Co)O particles. After oxidation for 1680 h, no further migration of Cr is detected in the thermally converted coating region. A low oxidation rate of 5.9 × 10^?14 g² cm^?4 s^?1 and area specific resistance of 12.64 mΩ·cm² is obtained for Fe_1·5CoNi_0.5 coated steels.     

Sputtered Ir–Ru based catalysts for oxygen evolution reaction: Study of iridium effect on stability

Magnetron sputtered low-loading iridium-ruthenium thin films are investigated as catalysts for the Oxygen Evolution Reaction at the anode of the Proton Exchange Membrane Water Electrolyzer. Electrochemical performance of 50 nm thin catalysts (Ir pure, Ir–Ru 1:1, Ir–Ru 1:3, Ru pure) is tested in a Rotating Disk Electrode. Corresponding Tafel slopes are measured before and after the CV-based procedure to compare the activity and stability of prepared compounds. Calculated activities prior to the procedure confirm higher activity of ruthenium-containing catalysts (Ru pure > Ir–Ru 1:3 > Ir–Ru 1:1 > Ir pure). However, after the procedure a higher activity and less degradation of Ir–Ru 1:3 is observed, compared to Ir–Ru 1:1, i.e. the sample with a higher amount of unstable ruthenium performs better. This contradicts the expected behavior of the catalyst. The comprehensive chemical and structural analysis unravels that the stability of Ir–Ru 1:3 sample is connected to RuO₂ chemical state and hcp structure. Obtained results are confirmed by measuring current densities in a single cell.     

Complex study of protective Cr3C2–NiAl coatings deposited by vacuum electro-spark alloying,pulsed cathodic arc evaporation,magnetron sputtering,and hybrid technology

Coatings were obtained by vacuum electro-spark alloying (VESA), pulsed cathodic arc evaporation (PCAE), magnetron sputtering (MS) techniques and VESA-PCAE-MS hybrid technology using Cr₃C₂–NiAl electrodes. The structure of the coatings was analyzed using scanning and transmission electron microscopy, X-ray diffraction and energy-dispersive spectroscopy. Mechanical properties were determined by nanoindentation, while tribological properties were assessed using pin-on-disk tribometer. Corrosion resistance was estimated by voltammetry in 1 N H₂SO₄ and 3.5%NaCl solutions. Oxidation resistance tests were performed at 800°С in air. The VESA coating had the highest thickness, low friction coefficient and high wear resistance. PCAE coating demonstrated the highest hardness (24 GPa) and elastic recovery (59%), oxidation resistance and superior corrosion resistance both in 1 N H₂SO₄ (i_corr = 70 μА/cm²) and 3.5%NaCl (i_corr = 0.74 μА/cm²) solutions. The MS coating had average mechanical properties and low corrosion current density (71 μА/cm²) in 1 N H₂SO₄. Deposition of coatings using VESA-PCAE-MS hybrid technology led to an increase in corrosion and oxidation resistance at least by 1.5 times in comparison with the VESA coating.     

Magnetron sputtered LSC-GDC composite cathode interlayer for intermediate-temperature solid oxide fuel cells

The paper investigates the influence of the La_0.6Sr_0.4CoO_3-δ-Gd_0.1Ce_0.9O_1.95 (LSC-GDC) composite cathode interlayer on the operation of solid oxide fuel cells (SOFCs). Thin composite layers with the different GDC content are obtained by the reactive magnetron sputtering. The impact of the high-temperature annealing on the LSC-GDC phase composition is studied by the X-ray diffraction instrument using additionally a synchrotron radiation. The NiO-YSZ anodes with the YSZ electrolyte thin film and GDC barrier layer are used for the SOFC fabrication. The current-voltage curves and impedance spectra of SOFCs are obtained in the temperature range of 700–800°С. It is shown that not annealed composite layers with ～50 vol% GDC content possess the most efficient electrochemical activity. The maximum power density of the SOFC with the LSC-GDC interlayer is 1322, 1041 and 796 mW/cm² at 800, 750 and 700 °C, respectively, which is 20–35% higher than that of the cell without cathode interlayer.     

Optical and electrical properties of ITO film on flexible fluorphlogopite substrate

Indium Tin Oxide (ITO) films were prepared, at room temperature, on a fluorphlogopite substrate using magnetron sputtering technology. At various temperatures of 500 °C, 600 °C, 700 °C, 800 °C, and 900 °C, the samples were (had) annealed for 2 h (a 2-h duration). The results showed improvement in the crystalline performance of ITO film at selected annealing temperatures, with a significant reduction in resistivity at 800 °C. The lowest resistivity is 4.08 × 10^?4 Ω-cm, which is nearly an order of magnitude lower than the unannealed sample. All samples have an average light transmittance above 85% in the visible light range (400–800 nm), and with increasing annealing temperature, the average light transmittance tends to decrease. Besides, at the sensitive wavelength of 550 nm, the light transmittance is as high as 93.74%. The sheet resistance testing of the sample was through the number of bending times, which revealed that with the increase of the number of bending, the sheet resistance increases. However, after 1200 bending times, the change rate of the sheet resistance remains below 5%. Thus, the ITO film prepared on the flexible fluorphlogopite substrate revealed excellent optical and electrical properties, good flexibility, and improved stability after high-temperature annealing, which guarantees successful application in flexible electronic devices.     

Effect of the thicknesses of the Al2SiO5 ion conductor on the opto-electrical properties for all-solid electrochromic devices

In this study, an all-solid-state electrochromic device (ECD) with the structure of ITO/WO₃/Al₂SiO₅/NiO_x/ITO was prepared, and the effect of the Al₂SiO₅ solid electrolyte thicknesses on the opto-electrical performance was investigated. The microstructure and surface morphology were characterized using XRD, SEM and AFM, and the surface morphology and degree of surface looseness demonstrate a significant influence on the opto-electrical properties of ECDs. The charge transfer dynamics at the solid-solid interface were characterized using EIS to obtain an ionic conductivity of 4.637 × 10^-8 S/cm. CV, CA and UV–Visible spectra were employed to record the in situ electrochemical and optical properties. The results revealed that the highest optical modulation was 44.58%, the coloring and bleaching times were 14.8 s and 3.7 s, and the highest coloring efficiency was 98.17 cm²/C, which indicates that excellent opto-electrical properties were obtained. When the thickness increases, the degree of surface dense morphology transforms, and the loose morphology is more favorable for ion conductivity, which improves the opto-electrical properties. The results in this study provide insights into the understanding of Al³⁺-based all-solid-state ECDs, which promote the exploration of new types of Al³⁺ ionic conductors for all-solid-state ECDs.     

Recrystallization behavior,oxygen vacancy and photoluminescence performance of sputter-deposited Ga2O3 films via high-vacuum in situ annealing

Ga₂O₃ films were deposited on Si substrates through radio-frequency magnetron sputtering at room temperature and were annealed in situ in a high-vacuum environment. The as-deposited Ga₂O₃ film exhibited an island-like surface morphology and had an amorphous microstructure, with a few nanocrystalline grains embedded in it. After high-temperature in situ annealing, the films recrystallized and exhibited coalesced surfaces. Because of the thermally driven diffusion of Ga, the interfacial layer between Si and Ga₂O₃ was composed of SiGaO_x. Compared with ex situ annealing in air, in situ annealing in high vacuum is more advantageous because it enhances surface mobility and improves the crystallinity of the Ga₂O₃ films. The higher oxygen vacancy concentration of in situ annealed films revealed that oxygen atoms were easily released from the Ga₂O₃ lattice during high-vacuum annealing. Photoluminescence (PL) spectra exhibited four emission peaks centered in ultraviolet, blue, and green regions, and the peak intensities were significantly enhanced by thermal annealing at >600 °C. This work elucidates the effect of the in situ annealing treatment on the recrystallization behavior, interfacial microstructure, oxygen vacancy concentration, and PL performance of the Ga₂O₃ films, making it significant and instructional for the further development of Ga₂O₃-based devices.     

计及风险规避的电力零售商平衡市场交易模型

由于新能源出力以及终端负荷需求的不确定性,电力零售商在日前市场的竞标电量与实时市场的购买电量之间存在不平衡而产生惩罚成本风险。引入用户侧可控负荷作为平衡资源参与市场交易,提出了一种风险规避程度指标,以此来度量交易前后电量偏差程度,以信息熵度量残差序列离散程度计算风险规避程度指标。以电力零售商运行收益、用户需求响应满意度以及风险规避程度最大为目标建立多目标风险规避模型,采用自适应权重粒子群算法进行模型求解。通过算例表明,所提出的模型从电网-电力零售商-用户多个角度去考虑电力零售商参与平衡市场交易策略,能够有效提高电力零售商的运行效益以及用户满意度,同时可以提高电力市场管理的可靠性与安全性。