储层应力敏感性影响因素研究

全面分析储层应力敏感性产生的机理认为，外部因素的改变会引起储层产生应力敏感性．而储层岩石物性等内部因素对应力敏感性的强弱起决定性作用。室内岩心应力敏感性评价时．仪器与设备的精度、加载与卸载方式、实验用流体类型以及各种人为因素等都会对评价结果产生影响，其中岩心密封套在高压、高温条件下的密闭性会对实验结果产生较大影响。所以储层应力敏感性不应该从孔隙度和渗透率的高低进行简单评价，中、高渗储层和低渗储层在生产过程也都可能表现出较强的应力敏感性现象。     

Effects of genotype and treatment on the antioxidant activity of sweet potato in Taiwan

Six genotypes of sweet potato commercially available in Taiwan, including TNG57, TNG66, TNG68, TYY1, RP and WP, were used as samples in this study of the effects of steaming and kneading with pre-steaming treatments on the antioxidant components and antioxidant properties of methanolic extracts. Steam treatment increased the total phenols contents of all genotypes (2–13 times), flavonoids content of RP (1.3 times) and anthocyanins contents of RP and WP (5–6 times). Steam treatment also increased the reducing power and scavenging DPPH radical effect of sweet potato flours. For the methanolic extracts of steamed and kneaded flours, reducing powers were 0.02–1.70 at 5.0 mg ml⁻¹ and the scavenging effects on DPPH radicals were 19–92% at 2.5 mg ml⁻¹. Both showed the order of RP > WP > TYY1 and TNG66 > TNG57 and TNG68. However, the chelating effect of the six genotypes at 1.0 mg ml⁻¹ ranged from 50% to 73%. Contents of total phenols, flavonoids, and anthocyanins of sweet potato flours were significantly positively correlated with the reducing power and scavenging DPPH radical effects. After steaming and kneading treatments, RP showed the highest increase in the contents of total phenols, flavonoids and anthocyanins among the six genotypes studied.     

Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

秸杆材料用作草皮栽培基质的研究

本文介绍了秸杆毡的成型工艺 ,通过植物所需的水、肥料和空气三种因素对秸杆毡的化学和物理性能进行了研究 ,该材料可被用作草皮栽培基质     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

可循环泡沫钻井液在宝302井欠平衡井段的应用

介绍了可循环泡沫钻井液的配方，性能及在宝302井欠平衡井段中的应用情况，结果表明该体系悬浮和携岩能力强，抗高温，抗污染效果好，能够满足宝南区块深井欠平衡压力钻井的需要，且保护油气层效果好，同时，这也是国内首次将可循环泡沫钻井液成功应用于井泥岩及煤层井，拓宽了泡沫钻井液的应用范围。     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.