高导电性原油电脱盐工艺研究

南阳原油中金属含量较高,掺有部分3次采油采出原油,加工时易造成电脱盐装置原油乳化,电导率高,脱盐难度较大。装置投产十几年来脱后含盐一直不合格,经过改造仍然超标,常压塔顶腐蚀严重。为此,对原油进行了电脱盐工艺条件及破乳剂研究,研制出了高效电脱盐设备和生物复合脱盐剂及降电流剂,采用平流弓形电极进行改造,解决了该原油的电脱盐问题,使脱后含盐达到3 mg/L。     

微晶合金在电流互感器中的应用

从微晶合金的性能特点出发，分析了其在电流互感器中的应用前景。     

Prediction of processing-induced distortion of curved flanged composite laminates

It is well known that angles in composite parts contract as they are cooled down from the curing temperature, this is often referred to as spring-in. It is caused mainly by the significantly different thermal contractions and cure shrinkage's experienced between the fibre direction and the through-thickness direction during the manufacturing process. A number of works have reported on the spring-in of straight angle composite parts. However, little has been done to investigate the distortion of curved flanged composite parts, which will distort differently owing to the introduction of the additional curvature, thus constraint.

In the present work, the distortion of the circularly curved flanged laminates is studied numerically. The finite element method is used to predict the processing-induced distortion of the part with two different approaches. In the first approach, the shear angles of the composite plies are predicted by a draping analysis. The effect of the fibre shearing on the mechanical properties of the laminates is considered in the model used to predict the distortion. The second simplified approach assumes that the in-plane properties of the laminates are isotropic. The results obtained by these two approaches are compared with those obtained experimentally.     

大型对开组合齿圈工艺设计分析及其最优化

本文论述了大型齿圈的结构特征及其现行工艺的合理性；在建立工艺关键环节概念的基础上提出工艺优化方案。并从理论上论证了实现最优化的充分可能性。     

Pulse-Width Dependence in Current-Driven Magnetization Reversal Using GaMnAs-Based Double-Barrier Magnetic Tunnel Junction

We have investigated the current pulse width dependence on current-driven magnetization reversal in double-barrier structures using GaMnAs-based magnetic tunneling junctions (MTJ) in order to clarify the origin of low threshold current density for current-driven magnetization reversal. Comparing with the case of single-barrier MTJ, the pulse-width dependence reveals that threshold current density is reduced by double-barrier MTJ. We confirmed that the threshold current density in the order of 10⁴ A/cm² is estimated considering the effect of current pulse width.     

An analysis of the electrical conductivity in BaSO4-added Ag2SO4 solid electrolyte system

The compositions (1 −x)Ag₂SO₄−(x)BaSO₄, wherex=0·01 to 0·6, were prepared by slow cooling of the melt. The extent of the solid solubility of Ba²⁺ in Ag₂SO₄ was determined by X-ray powder diffraction and scanning electron microscopy. The bulk conductivity of each sample was obtained using a detailed impedance analysis. The partial substitution of Ba²⁺ results in the enhancement of conductivity in compliance with the classical aliovalent doping theory. A simplistic model based on lattice distortion (expansion) due to partial substitution of Ag⁺ by the bigger Ba²⁺ has been considered to explain enhanced conductivity. Beyond solid-solubility limit (5·27 mole%) the BaSO₄-dispersed Ag₂SO₄ conductivity follows the usual trend seen in binary systems. An increase in conductivity in this case is discussed in the light of interfacial reactions and surface defect chemistry. The maximum conductivity in 20 mole% BaSO₄ dispersed Ag₂SO₄ is due to percolation threshold.     

褶积与逆褶积技术在核物理测量中的应用

讨论了褶积与逆褶积技术在核物理测量,主要是波形和能谱测量中的应用。还介绍了褶积与逆褶积的数值计算方法,给出了计算公式。     

轻便型γ能谱测井仪几个关键技术问题的探讨

为研制性能好，功能强，微机化学程度高的轻便型γ能谱测井仪，针对非油气测井工作的井口径小（〈φ６０ｍｍ）井身浅（〈１０００ｍ）等特点，探讨了γ能谱测井仪的轻便化，测量精度，信号传输技术，稳谱技术及微机化等关键技术问题。     

0.5级电子式电能表的设计与实现

本文论述了一种普及型电子式电能表的设计原理和实现方法，具体讨论了时分割乘法器和电流互感器的组成和误差分析，最后给出测试结果。     

多功能半导体激光医疗仪电源的研制

根据“多功能半导体激光医疗仪”整机的要求,采用同一电源对667nm和808nm半导体激光器实施供电。为避免电源在开、关机时对半导体激光管产生浪涌冲击,电源在设计中采用了适当的逻辑功能。并可保证对667nm激光器供电时,即使打开808nm激光器供电开关,也不对808nm半导体激光器供电,反之亦然。电源设有手动、计算机两种控制方法,及恒定功率、电流两种工作方式。