控制爆破法处理卡钻事故

介绍了在包头市某工程实施管道穿越黄河施工中,采用爆破法处理卡钻的经验。针对深水环境条件及钻杆内径小不宜采用集团装药的条件,确定采用"小直径爆破筒,钻杆内部装药"的爆破方案,阐述了爆破设计及施工注意事项。可供类似工程参考。     

Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.     

Importance of optical homogeneity for high-quality transparent ceramics

Two types of transparent Y₂O₃ ceramics without including large scattering sources such as residual pores, one with very high optical homogeneity (type A) and another one with slightly insufficient optical homogeneity (type B), are purposely prepared, and their optical properties are investigated and compared qualitatively and quantitatively. Type A ceramic exhibits transmittance characteristics with very low internal loss in the visible to infrared wavelength region, while type B ceramic is inferior in various optical performances especially in the short (visible) wavelength region. In type B ceramic, birefringence occurs due to optical inhomogeneity in the visible region, resulting in a decrease in the extinction ratio. Non-uniform refractive index distribution is also observed in the Schlieren image of type B ceramic, hence the laser beam quality through that material is degraded. This study proved the importance of optical homogeneity of transparent ceramics and clarified the problems in actual applications.     

A 6-DOF humanoid wall-climbing robot with flexible adsorption feet based on negative pressure suction

A wide range of dangerous and special tasks have witnessed the applications of wall-climbing robots, but they still cannot adapt well torough or sloping walls. This paper proposes a 6-DOF (degree of freedom) humanoid wall-climbing robot (HWCR) based on the principle of negative pressure suction. HWCR has the advantages of flexible adsorption feet, strong adaptability, strong anti-subversion performance, and high friction to the wall. We deduce mechanics formulas and carry out a parametric design of the foot structure so that it can meet the requirement of robot wall climbing. We use Fluent to analyze the flow field of the adsorption foot and determine the motor speed that can provide a reliable adsorption force. Using the D-H matrix to plan gait, we also design a compound cycloid-based foot trajectory to reduce the impact between the HWCR and the wall. Experiments on the uneven wall and sloping wall show that the vehicle can walk with an ideal gait, and the resistance value of the servo on each joint is much lower than the critical value, which ensures the smooth movement of the HWCR.     

Structural,electrical, and linear/nonlinear optical characteristics of thermally evaporated molybdenum oxide thin films

Homogeneous thin films of Molybdenum oxide (MoO₃) were grown on quartz and glass substrates using the thermal evaporation method. XRD results showed that the MoO₃ powder has a polycrystalline structure with an orthorhombic crystal system whereas the MoO₃ thin films have amorphous nature. SEM images showed that the MoO₃ thin films have a nearly uniform surfaces with worm-like shape grains. The film thickness influences on the linear and nonlinear optical characteristics of MoO₃ thin films that were examined using spectrophotometric measurements and from which, the linear optical constants of the MoO₃ thin films were estimated. The electronic transition type was determined as a direct allowed one. The values of the optical band gap were obtained to be in the range of 3.88–3.72 eV. The dispersion parameters, third-order nonlinear optical susceptibility, and the nonlinear refractive index of the MoO₃ thin films were determined and interpreted in the light of the single oscillator model. The temperature dependence of the DC electrical conductivity and the corresponding conduction mechanism for the MoO₃ films were investigated at temperatures ranging from 303 to 463 K.     

Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

Controlled growth of Bi-Functional La doped CeO2 nanorods for photocatalytic H2 production and supercapacitor applications

The rapid increase in energy consumption has severely rehabilitated human life urging to develop reliable and environmental friendly energy storage devices. Target oriented, systematic approach has been adopted to synthesis La doped CeO₂ nanostructures with percentage as La_xCe_1-xO₂ (X = 0,1,3,5,7) for potential super capacitors applications. Morphological doping impact on H₂ production, electrochemical and optical properties are thoroughly investigated. XRD studies revealed the crystalline phase purity and attained approximately 35 nm average crystallite size. The SEM images exposed that primary morphology nano-particles has been tuned into nanorods by increasing the La concentration in CeO₂ with size range 40～60 nm. CV graphs depicted that the prepared electrodes obey the pseudo capacitive faradaic reactions behavior in nature. Maximum capacitance (925 F g^-1) has been achieved by La_0·05Ce_0·95O₂ which is better than numerous reported materials. The La_0·05Ce_0·95O₂ also exhibited excellent GCD stability with 87.8% retention exhibiting it suitability for supercapacitor applications. Furthermore, the La_0·05Ce_0·95O₂ showed the significantly higher H₂ (9 μmol h^?1g^?1) production rate as compared to undoped CeO₂ and La_0·01Ce_0·99O_2, La_0·03Ce_0·97O₂ samples. This higher production is attributed to the recombination rate and have strong substantial correlation with optical characteristics.     

Novel one- and two-dimensional InSbS3 semiconductors for photocatalytic water splitting: The role of edge electron states

Photocatalytic water splitting has become a promising technology to solve environmental pollution and energy shortage. Exploring stable and efficient photocatalysts are highly desired. Herein, we propose novel low-dimensional InSbS₃ semiconductors with good stability based on density functional theory. Such InSbS₃ structures could be obtained from their bulk crystal by suitable exfoliation methods. Our calculations indicate that two-dimensional (2D) and one-dimensional (1D) InSbS₃ nanostructures have moderate band gaps (2.54 and 1.97 eV, respectively) and suitable band edge alignments, which represents sufficient redox capacity for photocatalytic water splitting. 2D InSbS₃ monolayer possesses oxygen evolution reaction (OER) activity and 1D InSbS₃ single-nanochain possesses hydrogen evolution reaction (HER) activity under acidic conditions. Interestingly, two edge electron states can be introduced when the dimension of InSbS₃ is reduced from 2D to 1D and the new electron states can exist in arbitrary-width nanoribbons, which can effectively promote the process of HER. Moreover, InSbS₃ monolayer and single-nanochain also exhibit large solar-to-hydrogen efficiency, high carrier mobility, and excellent optical absorption properties, which can facilitate the process of photocatalytic reactions. Our findings can stimulate the synthesis and applications of low-dimensional InSbS₃ semiconductors for overall water splitting.     

Anchor plate bearing capacity in flexible mesh facings

This work addresses the problem of the loading capacity of an anchor plate coupled with a steel wire mesh in soil retaining applications. The interaction mechanism between the flexible mesh facing, the underlying soil layer and the plate is studied starting from the results of several laboratory punch tests involving both the plate and the mesh only, and the whole soil-mesh-plate system. The experimental tests have been reproduced by adopting a 3D discrete element model where also the wire mesh is discretized as an assembly of interconnected nodal particles. The interaction between these particles is ruled by elasto-plastic tensile force–displacement laws in which a distortion is introduced in a stochastic manner to account for the wires’ geometrical irregularities. The mesh model is then validated with reference to a set of punch tests in which the shape and size of the punching element as well as the nominal wire diameter were varied. Subsequently, the model is extended to a punch against soil test configuration permitting an insight into the nontrivial local mechanism between the mesh facing and the underlying granular layer. The good agreement between the numerical predictions and the experimental observations at the laboratory scale allowed us to extend the model towards more realistic field conditions for which the role of the mesh panel boundary conditions, the mesh mechanical properties, the soil mechanical properties and the anchor plate geometry is investigated.     

Upconversion nanoparticles: Recent strategies and mechanism based applications

Upconversion nanoparticles (UCNPs) doped with lanthanides can convert near-infrared excitation into UV and visible emissions. Because of their relatively high emission efficiency, UCNPs are appealing materials for use in a variety of sectors. UCNPs are known for low auto-fluorescence, excellent chemical and thermal photo-stability, deep tissue penetration, exceptional biocompatibility, low toxicity, color purity, and ease of surface functionalization. In this review, we explain a few recent strategies to boost the efficiency and luminescence of upconversion nanoparticles and minimize quenching by fabricating them as core/shell, nanofibers, or heavily doped lanthanides. Applications of UCNPs in drug delivery, Photodynamic therapy (PDT), biosensors, bioimaging, and optogenetics are also discussed along with their mechanism of action. Our motivation for this review is to understand the working mechanism of UCNPs and their applications in various fields.